FSG446RHS0 Frigidaire Dryer - Instructions

As others have described in more detail... I lifted the top, removed the 2 screws holding the front panel (one on each side, inside the control panel on either side - not the easiest to get at, but not too bad), popped the clips holding the front panel in place and removed it. With the front panel off, the location of the coils is obvious (lower left side). The only challenging aspect of this repair is that the 2 screws holding the coils in place are really torqued in so it was crucial to use the exactly correct size screwdriver and not let the screwdriver slip while unscrewing those screws. Actually swapping out the coils took seconds, of course they have to go in exactly the same way as the old ones. I did take a few minutes extra to vacuum out years of lint from the inside of the dryer. Overall, much easier and cheaper than I was expecting and now I know where everything is inside the cabinet.

Thanks to Justin in Customer Service I was able to get the correct replacement knob. It arrived and I installed it in seconds flat. It works great and you'd never know it wasn't original.

Thanks.

1. unpluged the dryer and turned off the gas.
2. pulled dryer out so i'd have ample room to work on it.
3. used large flat blade screwdriver in the front between the top lid and dryer face to gently pop-up the lid.
4. removed 4 screws from inside, that hold the face to the main box leaving the wires all intact.
Found the coils on the lower left, held in place by two screws and plate.
5. took a good look at thier orientation before unpluging old and installing new, I recommend one at a time.
6. Vacuumm any exceess lint and check foam seal between lint trap and exhuast duc, the glue came undone on mine causing extra lint dust that is potentially flamable.
6. screw dryer front back on to main box, make sure to check wiring harness and that all electrical blade connectors are still pluged in to their componants.
7. At this point plug in, turn on gas and do a test run.
8.if everything checks out good then lower top make sure flexable exhuast hose is still connected on hte back of the dryer.
9. Tell your wife or girlfriend or husband or boy friend they can now finish your laundry :)

There was a lot of screws. And I cleaned everything well. The one part was bad so I replaced them all to make sure it'll last.

Main problem was the bearing, replaced the belt and felt seal as well
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again

The conversion kit had everything needed, However the instructions were lacking in description on how to assemble everything, this kit includes the new style burner, igniter, igniter mount, air shutter and propane orifices. A detailed picture would help.
The hot surface igniter was broken in the box, luckily the dryer had the same style igniter already installed. I just had to reposition the original igniter to light properly. No special tools needed. Read the instructions before installing.

followed the instructions video on the site had no problems just took about 2 hrs to complete

Once I found this site, with everybody's description of the problem & fix, it was pretty easy.
Pry the front of the top up using a flat screwdriver at each side. Then disconnected the dryer-controls wire bundle (dryer unplugged of course) at the connector, and unscrewed 1 screw on each side of the front panel close to the top (under the controls, back-side of the panel), in order to pry the front panel off - top 1st.
With everything opened up, just unscrew the two screws on top of the burner coil. the pull off the plate, slip off the 2 coils, disconnect the wires, and install the new coils in reverse. Put it all back together and you're good!
(I replaced the drum glides too, while I was in there - just in time!)

Just pressed the knob on.

It was very easy, looked and found the right match and pulled off the broken one and pushed on the new one

Just put on the new knob! Supper easy and it works great!

All I had to do was line the "D" shaft up with the "D" metal shaft on the Dryer and push the knob on. I made sure it would turn properly, and turned the Dryer on the make sure it worked. All is good.

Took it out of the bag and put it on.

Simply popped it back into place, careful not to break the new handle.

Unplug from electric outlet. Use putty knife to press on two brackets holding the top cover. Raise top cover. Unscrew two screws holding the front panel. Raise front panel up and move to the right (careful with the wires). Disconnect wires from coils. Unscrew two screws holding a small bracket holding the coils. Replace coils and reassemble everything. (HINT: make sure you drum is empty. Mine contained dump clothes, and it turned out front panel actually provides support to the drum, so mine was hanging there with some weight in it - probably not good).