All Installation Instructions for Roper Range FES325RQ2

Burner wouldn't regulate temperature

Turned off power to range. Took back panel off to reveal all controls. Pulled off knob of bad control. Removed 2 screws from the front of the control. Pulled off wiring from back of old control. Took new control reversed procedure. Reinstalled back panel turned power on and tested new control. Total time about 20 minutes

Parts Used:

Surface Burner Element Switch, Large Burner

Michael from THE VILLAGES, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken drawer glide

Used a phillips head screwdriver to remove the single screw holding the part in place and put the new one on. Finding the part on this site was a breeze and it arrived quickly. A first rate experience all around.

Parts Used:

Range Rear Drawer Glide

karen from Thornton, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Worn/Bulb Socket

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Parts Used:

SOCKT-LITE

JOSEPH from COON RAPIDS, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

2 Service Elements Didn't Work (Didn't heat up)

Unplugged old elements and plugged in new ones

Parts Used:

Range Surface Element

Standard Y-Frame Range Surface Burner

Roseann from MEADVILLE, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven heating coil snapped and would no longer heat.

It was so easy to change this out. Unplugged the stove and removed a couple of screws on mounting plate and pulled out the old heating element. Plugged in the new one and replaced the screws. Problem solved!

Parts Used:

Range Receptacle Kit

Diane from Gillett, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Removing an heating element that burnt into .

Unplugged oven , removed screws ,pulled wires out, removed old element , just hooked wires up , screws .make sure it sits level plugged in. Works great

Parts Used:

Oven Bake Element

Jenny from GREENFIELD, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Old drip pans made to heating element un ever

Replaced drip pans and now everything is level.

Parts Used:

Drip Bowl - 8 Inch

William from DANBURY, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Rear drawer slide was broken.

Undid one screw. Removed the broken slide. Replaced with new slide an fastened with the existing screw. Problem solved.

Parts Used:

Range Rear Drawer Glide

David from Mauldin, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven Demon Possession

Our repair was extrodinarily easy. As my husband was taking out the old element and the oven was off, the element heated up and actually burned him. He readjusted it and it refused to heat again. We figured at that point that there must be a short, so we never even opened the box with the new element. A short time later we decided to use the top of the stove for soup and a small fire started in the oven. We turned off the braker at that point and ordered a new oven.

Parts Used:

Broil Element

Kevin from Greensboro, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The heating element on the left front burner was out

Pulled the old one out and plugged the new one in. It was that simple!

Parts Used:

Range Surface Element

Julie from Salt Lake City, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

baking element non operational

removed two screws to faceplate at rear of oven. Disconntected contact wires, installed bake element reconnected contact wires, attached faceplate turned on oven holy hell it works just saved some money on service call thanks!!!

Parts Used:

Oven Bake Element

GARY from JACKSON, WY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

slides on lower drawer were broken

I used a phillips screwdriver and replaced the part with one screw.Very easy and replaced my lower drawer under my oven,it tool about three to five minutes at the most and my drawer works fine now.Thanks for the instruction video on line, it really helped.

Parts Used:

Range Rear Drawer Glide