DWXR485EB2CC General Electric Dryer - Instructions

took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal

I pulled the panel off of the dryer, screwed the part back on the correct wires, replaced the panel.

First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.

I took out a whooping four (4) screws, two that held down the top to the front panel then two screws that attached the side panels (at the top) to the front panel, raised the drum from the inside, leaned the front panel foreword, popped out the old slide (there was only one left), installed the four new slides & put it back together. That's pretty much all there was to it, vary simple.

Looked up the problem and solution on the web and,ah-ha, drum slides should be the cure. Easy to install, . Back to the internet to discover that after the slides, the bearing and felt liner were the next likely culprits. Again easy install, but to no avail. Calling in the pros.

remove move 2 screws holding top of dryer down.then remove two top screw holding front panel on so i could get to were my slide bearing where at poped them out and slide in new ones then put it all back together that was it

todd e line eaton ohio usa

Imagine that!! Move 3000 miles from home to home and after 90 days in storage, we finally get our things. First the washer, then the dryer. Test, no water, okay...Open valves. It's like magic. Hmmm. Plug the dryer in. No sound, not a peep. Turn the start switch one more time, crack-crack, the knob falls in my hand. Ordered the part and got in 2 days. A few star bolts to remove, unplug 3 wires and presto, it works like magic. Thanks!!!

Pulled power plug. Removed the "Start/Stop knob" Removed 4 starbit screws across the top of the control panel. Flipped control panel down(toward front of dryer)to expose swithes. Aligned the new switch next to the switch being replaced, removed a wire and re-installed on the new switch. I did for each wire. To remove old switch, rotate counter-clockwise and lift out. Line up slots on new switch to panel slots, push down and rotate clockwise to lock in place. Re assemble panel, line up slot on switch knob to switch shaft and press on.

I took off the dryer top and saw it was the slides went on line found PartsSelect, found my dryer, ordered the parts and had them within two days and it took me about 15 minutes to fix the dryer which will add about 3-4 years more life on it. Thank You PartsSelect My wife is even happier

snap in snap out

Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.

i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.

Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.

Verified start switch was defective by jumping around switch to confirm the unit operated. replaced the switch.

Just like the other stories, remove the top and front of the dryer, replace the bearing and slides (or slides only if needed). I ordered only the slides, but also needed the bearing because I didn't realize the drum had worn through the bearing already.