Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Very loud squeek in rear of dryer
The part arrived in only 3 days and I didn't even pay for express shipping!
Once I popped the top lid off, and removed the two screws holding the front on it was a breeze from there. Simply take the drive belt off by loosening the spring loaded tensioner on the bottom, lift entire drum slightly up and then out. Remove the screws to replace bearing on rear of drum (4) and the screws that hold the bushing assembly in place (2). Reverse the process and you will be up and running in no time at all.
I was about to buy an ew washer and dryer set, but thanks to PartSelect.com, i saved over $1000!
Searched dryer model on Google, found partselect.com. Searched for Dryer model and a diagram of the dryer with all its parts appeared. Selected the timer knob on the diagram and it took me to the part, ordered it. All steps took less than 10 minutes, and I had the new knob in my hands the next day and installed in about 3 minutes. You saved a few dollars, plus not having to miss time from work waiting for a repair man. Thank you! Rocio
Removed front and top panals to dryer. Installed belt over the drum. opened back air vent panal and installed belt to pully. Reinstalled back top and front panals. Done.
First of all I am NOT a do-it-yourself handyman. I unscrewed the panel where the start knob was diagnosed I needed an electrical switch that went behind the panel and a new start knob. PartSelect was great. just plugged in my model number, found the drawings of the model. I selected and ordered both parts for $40. Shipped normal delivery and they arrived in 5 days. I had the parts replaced, the panel screwed back on and the dryer working in 10 minutes. I highly recommend PartSelect for honesty, speed and helpful drawings that allow you to select the correct part. 110% satisfied.
Dryer was squeeking for a while, and then eventually just quit working.
Took the top and the front panel off (took me a while to figure this out without breaking stuff). Took off belt, pulled out drum, replaced bearing, and then I also had to replace the ball (attached to rear of drum, which slides inside the bearing).
My husband replaced the rotary start switch that we bought. However, the dryer still would not start. He then tested each remaining switch/dial (before we spent more money on parts) to see if the dryer would start if the electrical connection by-passed that part. None of the top panel switches was the culprit. Then he pulled the door switch. The dryer worked with the switch out, but still connected. He reset each wire, put the door switch back in place, and it failed again. He pulled the switch, added electrical tape to all the connections, and put it back. The dryer works fine now.
Two tips after you watch the videos (and video link)
Watch the videos for replacing the belt. The one by Kenmore is the most accurate even though it isn't GE -- the mechanisms are the same. Here is the link to the one I found most helpful: https://www.youtube.com/watch?v=G2wTmfurT5o
First: You don't need to pull the washer/dryer out at all. Leave it in place. You can put the belt around the drive shaft and get the tension pully in place by feel and inspect your work with a flasklight,
Second: There is absolutely no reason to spend $70 on a rubber belt. Other places sell it as cheaply as 10 dollars. Shop around -- the actual part is not at all impressive and should not be priced this high.
took the top off, then the front,there 2 screws that hold the front on. there's a yellow thing on the front took that off, it is held on with one screw. on the back of the dryer on the bottom is a metal plate take that off, to get to the belt take that off. then there' 3 screws in the drum, take them off ,then you can slid the drum out. then take 2 screws off the bearing bracket, that's it. easy
Had been broken off due to "plier" uasage.....duh!
Opened panel, bent retainer tab, took off wires. Took out switch, put in new switch, replaced wires and knob and plugged it in. Off she goes. PS, how the hell did you get that part to me in less than 24 hours??? Thanks guys.
Simply replaced it. I have ordered from Parts Select several times. Excellent customer service. They always have the parts that I need and ship them to me promptly. Great company!
The control switch broke off flush from the start switch
My wife was attempting to start a load of laundry when the start knob came off in her hand. I figured the inside of the knob had broken loose and the stem from the rotary start switch would be sticking out, well the stem had broken off flush and the knob was fine. After ordering a replacement, I jerry rigged the broken one with a large screw driven into it and put it back in place, worked great, just had to put a screwdriver into the screw and turn it to get the dryer to start. I felt it was fine to stay that way but the wife insisted we install the new one to put the knob back in place. The new switch arrived very quickly and went into without a problem, just four screws to remove the panel, two wire connections and was working again.
I ordered a selector knob and it was delivered in a short amount of time. I wasn't sure if it was the right one when I ordered it, but my husband just put it right on the dryer. He said it was perfect. Thank you PartSelect!