All Installation Instructions for Frigidaire Range CFES355EB1

Surface element shorted out

Tilted the surface unit and proped it up with the metal arm then I unpluged the old 8"-surface element and replaced it with the new 8"-surface element that I purchased from PartSelect.com. I then lowered the surface unit turned the burner knob on and everything worked fine. Thanks PartSelect.com.

Parts Used:

Surface Element - 8 Inch - 2600W

Claude from Baton Rouge, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Renewed drip pans

Replace the old ones with the new ones. Was VERY impressed with the quick delivery!!

Parts Used:

Drip Bowl - 8"

Chrome Drip Bowl - 6"

Frank from Winter Garden, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 6 people found this instruction helpful.

Was this instruction helpful to you?

heating elements not working

prepared the parts as directions displayed, removed the heating coils and popped the hood on the range, simple curcit 2 wires in to the main harness for each coil. snip, plug and twist add heat wrap to seal the new conections and done very simple fix saved me buying another oven....for now

Parts Used:

Terminal Block Kit

christopher from cincinnati, OH
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Control will not work - only clock blinks

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Parts Used:

Main Terminal Block Kit

Sue from Lampasas, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

0 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Broken globe in oven and burnt out light bulb

Easy as 1-2-3

Parts Used:

LENS

Light Bulb

Sharon from Foley, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 5 people found this instruction helpful.

Was this instruction helpful to you?

8" left front surface element would no longer heat properly

I ordered the exact replacement element, and after unpacking it, it took about 5 minutes (actually,less; didn't time it), and the new element was installed and working fine.Thank you very much.

Parts Used:

Surface Element - 8 Inch - 2600W

Robert from Greencastle, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

drip bowls on stove rusty

they were for my 90 year old mom. she dropped them in by herself, perfect fit....thanks very much

Parts Used:

Chrome Drip Bowl - 6"

Drip Bowl - 8"

Kenneth from Osseo, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Oven was not heating up to the set temperature. Stopped around 180-200F.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Parts Used:

Temperature Sensor

Robert from Glasgow, MT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Stove door switch was broken

used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..

Parts Used:

Door Switch

James from Milford, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

stove top element burned out & drip pans needed replacing

was very easy to replace the element, just pulled the old element out and eased the replacement in. was happy to find partselect.com to order what i needed. the order was filled correctly & delivered in a few day. it was good to be able to review how other problems could be solved & what parts to order

Parts Used:

Surface Element - 8 Inch - 2600W

Chrome Drip Bowl - 6"

Drip Bowl - 8"

genese from brantely, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Replaced burner block

Looked at the instructions and cut the wires, put the new wires in the block, attached the block to the range, put the new wires to the range wires using the wire nuts. I plugged the element into the block turned on the power, tried the element and it worked. It was really a easy repair.

Parts Used:

Terminal Block Kit

Glenn from Fossil, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

heating element didn't work

I did the repair in less then 5 minutes. I took out old element and put in new one and turned it on and I had heat. Works great Thanks the part came in 2 days what a wonderful suprise that was.

Parts Used: