This element is a genuine OEM replacement part, has looped terminal ends, comes with a black medallion center, and fits most electric ranges. All burners are made of a heating wire that produces heat from electricity. Remove the non-functional burner element from the terminal block (or receptacle). Use a multi-meter to check for continuity. Check the end of the terminals for corrosion or heat damage. If there is corrosion or heat damage, replace the whole terminal block or receptacle at the same time you replace the damaged coil. Before you start this repair, make sure that the element is turned off and cool to the touch.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Frigidaire Range 6-Inch Coil Burner Element
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Nelda H - February 17, 2022
Verified Purchase
Sooo Easy Repair
Range burner is so easy to install. Just be sure you order the correct burner.
★★★★★
★★★★★
Linda J - November 27, 2021
Verified Purchase
Burner Replacements
I now have all four burners working properly. Easy to install.
★★★★★
★★★★★
Kathryn U - March 26, 2021
Verified Purchase
Functional and safe replacement for 30 year old range
The hardware store element did not fit. Soup Pans were not level and tilted. Now there’s no fear of pans sliding off the stove because the Parts Select heating element is a perfect replacement.
★★★★★
★★★★★
JANET W - July 25, 2020
Verified Purchase
Burner Elements
Parts arrived in good time and are working very well.
Thank you.
★★★★★
★★★★★
Robin P - July 10, 2020
Verified Purchase
Easy repair. Quick delivery
Thank you for the quick delivery.
★★★★★
★★★★★
Winnie C - May 12, 2020
Verified Purchase
great part - worked great
The replacement burner was exactly what I needed - I'm cooking again! Your website made it very easy to find the part I needed - thanks.
★★★★★
★★★★★
JAMES D - March 2, 2019
Verified Purchase
great part
came fast stove is back working
★★★★★
★★★★★
Russell W - December 4, 2018
Verified Purchase
Easy installation, but part is damaged.
Inner coil higher than outside coils which makes a pan tilt. Bottom of pans only gets heated on one side. How do I get a replacement?
December 4, 2018
Hello,
Thank you for leaving a review on the part ordered. I have sent you an email in regards to the order. Hope to hear from you!
★★★★★
★★★★★
Clay P - May 30, 2018
Verified Purchase
Easy
Unplugged the old one and plugged in the new one. Nothing to it.
★★★★★
★★★★★
Jackie O - March 24, 2018
Verified Purchase
Excelent quality.
The got in very fast and in good condition
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.5 / 5.0, 13 reviews.
What's this?
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Burner element failed
Plugged the new one in and it worked. I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
Robert from New Castle, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The right front burner element shorted also taking out the surface burner switch.
I determined that the failure was due to age and wear on the element. Therefore I thought it wise to replace all four burners as a preventative measure. First unplug from power! Replacing the burners was plug-and-play simple. Replacing the switch was easy: Remove the back panel, pull the control knob and remove the two screws securing the switch. Move the terminals to the new switch (one at a time) and mount it with the two screws and replace the back panel. NOTE: The foot bracket on the large burners were about 1/32" too stout and the burner element would not seat in the ring properly. I made a slight adjustment with my grinder and everything fits perfectly.
A stainless steel cover was over the burner when it was turned on.
I removed the old burner, drip pan, and burner terminal block. Cut and stripped the wires. I used wire nuts to connect the wires and used shrink tube to secure the nuts. Installed the drip pan and the burner. Hint: When turning the burner on use a vent fan or open windows or doors to get rid of smoke from the new burner.
An aluminum saucepan had overheated and melted onto the element.
Unplugged the element and the melted on pot. Plugged in the new element. I thought I might need a whole new cooktop but a new element was very easy to find online.
Alice from Batesville, AR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no power to element/no heat
removed burnt out terminal block, installed new- I soldered wires instead of using wire nuts, took a little extra time, but I feel it's a better connection. I later found that my rotary control must have burnt out too, I swapped it with one from another burner. I'll be ordering a couple rotary controls next from this company. All parts were nice quality. Received quickly.
went go use oven and need heard a pop and dust smoke coming out vent , found lower element blew apart, since only store around was sears they didn't have part,so my son found your web site. so odered it came in 2 days, while going to order oven element we knew that one of the stove burner wasn't he
just unplug stove and unscrewed element out of back wall cleaned up mess and reinstalled. stove top you just pull out bake element and push back in
I just plugged it into the receptacle on the stovetop and turned the thing on, and it worked! I'd been without the 4th burner for quite some time. Nice to have it back!
Janet from North Vernon, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced elements
pull the element out and slide the new element in.No tools needed,it's that easy.
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Harry
June 4, 2019
Is the right front burner coil 6" or 8", how do you measure it?
Hello Harry, thank you for writing. This is the front left and right rear 6" Burner Element for your model. When measuring a stove's element, you measure from the outside edge to the outside edge. We hope this helps.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Moshe
March 28, 2023
Hi, I am trying to replace all four stove burners and drip bowls. Which of the 2 drip pans I found on the first page of the "items" fit this model? And what coils do I order to make sure I have all 4 that I need?
Thank you!
For model number CFEF311GSA
Hello Moshe, thank you for contacting us. According to our research, you may need to buy two surface elements 8", part number PS2339242, and two coil burner elements 6", part number PS2368974. You may also need to buy two 8" drip bowls, part number PS437595, and two 6" drip bowls, part number PS437596. We hope this helps!
Is this element compatible with a Whirlpool stove model rf263lxtt?
For model number PS2368974
Hello Karen, Thank you for contacting us. We have researched the model you have provided and have found
the part you are looking for is PartSelect Number PS11743366. We hope this helps!
Is this burner element compatible with Whirlpool stove?
For model number PS2368974
Hello Karen, Thank you for your inquiry. In order to verify if this part will fit your model, may we have the model number of your stove? We look forward to hearing from you.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
