All Installation Instructions for Jenn-Air Cooktop C202-C

Cartridge wire burned out

I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.

Parts Used:

Surface Burner Receptacle Kit

Robert from San Francisco, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set

Was this instruction helpful to you?

needed drip pans for burner

easy, drop in

Parts Used:

Drip Bowl - Chrome - 8 Inch

Drip Bowl - 6 Inch

Arva from Horsecape, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Heat Errosion

Wife installed them, they just snap into place on the Rock Grate.

Parts Used:

Rock Grate Support

Fred from Temple Terrace, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

burners would not come on without moving them around

took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing

Parts Used:

Surface Burner Receptacle Kit

Ronald E. from Marissa, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

heating coils would not work

Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.

Parts Used:

Surface Burner Receptacle Kit

Adam from Kempner, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Holes in the air filter of our Jenn-Air grill

Simply pulled the old filter out and put the new filter in.

Parts Used:

Range Grease Filter

Janice from Ocala, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Porcelan Electric Burner Plug broke

The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.

Parts Used:

Surface Burner Receptacle Kit

John J from Coatesville, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Filter worn out, exhasut fan kept going off

Old filter allowed too much air flow causing exhaust fan to go off....installed new filter in exhaust chamber...release clip on old filter and install new filter (at an angle) in the exhaust box....clamp down clip on edge of filter and job is complete

Parts Used:

Range Grease Filter

John from Cayce, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Broken switch

Turned off 50 amp breaker. Removed knob, unscrewed holding nut and unplugged each of five wires from broken switch and connected wires to new switch.

Parts Used:

Infinite Switch

Robert from Coral Springs, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

ugly old drip pans.

It was simple! The range looks so much better!

Parts Used:

Drip Bowl - Chrome - 8 Inch

Drip Bowl - 6 Inch

Cindy from Champaign, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

burner only work on high heat

Turn off circuit breaker to cooktop. Remove 2 screws that hold switch plate assembly.Remove tinnerman nut from old switch using adjustable wrench. Remove one wire at time from old switch to same location on new switch. Return shaft back through hole and replace nut, be careful to not overtighten. Replace control know, turn circuit breaker back on and test. Works like new. Neil

Parts Used:

Infinite Switch

neil from CONYERS, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench (Adjustable)

Was this instruction helpful to you?

The surface burner element burned out on my 20 year old Jenn Air electric stove.

It was so easy to order a new one from your company. And it arrived in less than a week! I slipped it into the electric outlet and it worked perfectly. THANKS. Wanda Major

Parts Used:

Surface Burner Element - 8 Inch

Wanda from Riverton, WY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Replacement

This down draft filter was just what I was looking for. The big box stores (Home Depot and Lowe's) do not carry this size filter. Thanks,

Parts Used:

Range Grease Filter

Barb from Holladay, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Burner receptacle had malfunctioned and been removed

10 Minutes for a stove my landlord thought was not fixable (repairman had already cut the wires to the element and capped them)! The delivery person handed me the package, I got out the single tool needed, installed the part, put away the tool, cleaned my hands, and put a pot of water on the stove to boil for pasta. 10 minutes!

Parts Used:

Surface Burner Receptacle Kit