BES384EC4 Crosley Range - Instructions

Simply took oven out of wall, removed back plate, unplugged old sensor, went in the front and unscrewed old sensor, put in new sensor, went in back and plugged in new sensor, put on back plate, push oven in wall. Turn on power

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

1 Turned off the oven breaker.

2. Removed the oven racks.

3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.

4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.

5. Installed the new sensor and now oven holds temperature steady.

Easy order, quick delivery and easy installation, happy wife.

Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

Pulled stove out and unplugged it.
Used a Phillips screwdriver to take the back cover off of the control panel.
Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control panel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others.
Replace back cover.
Plug stove back in and slide back into place.
There are you tube videos out there to help you.

With no install instructions (NOT good for diy-ers), looked through reviews and watched video for help. Replacement part - not same as original. Had to use magnifying glass to id the terminals / take a picture before disassembly. reassembled - found out terminals are different & black wire is too short. Took off element - rotated the clips one number counter clockwise, reassembled - removed black wire from harness for extra reach. Hooked up, lowered top for test. power on - everything OK. Power off - complete assembly. Power on - test. Seems to be good. When I called customer service for assistance because there was no instruction, they told me I should contact a local appliance repair person. (big joke).

Pulled range out from cabinet, removed back plate, two screws inside oven attaching the temp sensor. Then pulled the sensor and wire through from back. Reverse to replace about Ten minutes
OEM parts plug in same, works great

2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Phillips screwdriver used to remove 2 screws at top left in oven. Pulled thermostat out until I could get to the connector. Used pliers to hold wire, reconnected new plug , threaded it back into back of oven and reattached the two screws.
Saved $150 on a service repair call.

Googled the problem and found Oven Temperature Sensor and Main Terminal Block to be the most likely problems. Turned out to be neither. No parts were needed. Oven has a thermal overload switch on the rear upper left. Thermal overload needed re-set. To do so you have to remove the oven, remove the back and press the red button on thermal overload. Biggest challenge was figuring out how to remove the oven. Even with the installation manual it was not easy to fgure out. The instructions are misleading. You need a special tool. I used two hacksaw blades as a substitute, and slid them in to release the clips. Once you figure out how to get the oven out the rest is simple.

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.

removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,