ALW680RAW (PALW680RAW) Amana Washer - Instructions

checked for unbalanced load. still banging. removed lower front panel by removing 2 screws. then removed front top panel- 2 more screws. turned unit on spin cycle to see what was going on. this is dangerous as many moving parts are exposed, so keep everything clear. banging was the tensioner slamming back and forth. unpluged washer from outlet and felt along the belt to find part of the 'v' shaped balt had come part, leaving a gap in the "v". ordered part.when i got the part, i removed 4 larger bolts that held the motor, pully, and pump. i unplugged the wires for the motor, and removed the belt from the bsket side pulley assembly by slipping it off and under the shaft. i removed the torx screws that held the pump on the motor and removed the belt. PAY ATTENTION to how the belt was in between the pully and pump assembly or you will have to remove and redo it. reassemble the pump over the belt, pully, motor, and put the belt on the drum side pully before bolting it to the washing machine. it is fairly heavy and tight, so you might need help. this was not hard and you do not need to take apart the washer except for the two front panels and the motor assembly. i just pulled the unit away from the wall and tipped it back to access the inside. take your time and pay attention, and make sure it is not plugged into the wall and you should be fine.

I had no problem replacing the triple lip seal and bearing. I cracked the plastic tub, which after 10 years was very britle and cracked in two places ON THE SIDE. To remove the bearing I had to improvise a bearing removal tool using a puller I had on hand and a 1 lb metal coffee can. It worked great! You need to use some type of pulling device to remove the bearing without damaging the tub.

Replacing the spin belt is like the others have said, but I'll add a couple of cautions. Don't try to separate the driven pulley on the water pump from the pump shaft. Instead, separate the water pump from the driven pulley. And, make sure you know the routing of the belt for reassembly, because it has to go between the correct legs that support the water pump. Get it wrong and you'll have to start all over. I pulled the machine away from the wall by about 18" and put a block of wood under the front of the machine to raise only the front to 9" or 10" off the floor which made it easier to do the work. Try and take a digital photo of the belt routing from a couple of angles before beginning. Don't forget to route the belt around the tensioner pulley.

Basically you have to remove the drive motor and pump (in that order). This allows you to get the belt around the drive motor pully wheel. It took me a few tries to get the belt routed right. I assume that if you know what you are doing you can complete this in under an hour. It took me about 4 hours, though - cause I didn't know what I was doing at first. Hehe.

Hope this helps.

Replaced the mixing value using the kit purchased from PartSelect. The instructions with the kit plus the installation tips found on their WEB Page were extremely helpful. Everything went as predicted except I had to cut and insert a new piece of wire on the white wire between the hot and cold electrical connections. I used two crimp connectors to lengthen the wire. This was a very simple job for a 73 year old man like me. Thank you for the tips and quick delivery of the mixer value kit.

removed both hot and cold fill lines and front of washer panel. removed screw holding mix valve plate t the back of the washer . Unpluged connections to mix valve and replaced valve. ( note removing the top of the washer is needed and can only be done by first removing the front by sliding a thin screw driver between the top and front panel to release the clips at the ends.)

Removed spring, then hoses and then belts. When all was removed we loosen the old washer pump and installed the new pump. Everything was re-installed and was put to wash. At first it leaked water that was already sitting there, but then it work like new. Oh I also read the instruction on this website, I recommend the site to everyone!!

Removed old hose by sqeezing clamps and sliding off of fittings. Placed clamps on new hose. Slid hose on fittings. Repositioned clamps over end of hose. Job done.

Followed video on PartsSelect website, they made it real easy.

Removed front lower panel, removed 4 bolts holding motor, removed water hoses draining water into a pot, unplugged electrical connector on motor, removed motor, removed water pump from motor (torex bit), separated pump from motor. installed belt reassembled washer in reverse order. To my surprise, it worked and was easy.

We promptly received the part and easily installed it with no tools. We had an excellent experience. We found the old fabric softener dispenser after installing the new one. Now, we have two.

First, I removed the screws, then removed the pump. I, then, installed a new pump.

disconnected valve replaced with new, real easy. I removed motor and belt ,4 bolts, than removed 3 star screws from pump, replaced pump and replaced unit. Worked great!!!
Delivery of parts was faster than promised, standard shipping.

I ordered my part on Monday. It was delivered on Tuesday, and by four o'clock we were in business. I highly reccomend PartSelect.

Remove 3 screws on Washer control top. Then 3 screws holding clear cover and removed. Remove 3 phillips screws holding face of panel on and tilted panel to get at wires. Marked the wire colors on eace of 4 terminals and removed them. Used plires to push the top on the switch near the knob and turned the switch counterclockwise. When the lugs lined up the switch slid out the back. Just reversed the above to reinstall following the proper colors on the wires to reinstall. Washer works fine now.