6359 Maytag Washer - Instructions

Washer originally purchased from Sears. Called Sears for repair. $65.00 to show up. Diagnosed the problem as a Bad belt and pump. Asked for approx. $250 to repair. I declined and ordered a belt and pump from PartSelect.com for half the cost. Took 10-15 minutes to install. Turned the washer on and put it through a drain cycle, it leaked all over the floor. Turns out the only problem was a cracked Outer Tub to Pump Hose. It took about 10 minutes to install. Whala, no leak. Now while I purchased an un-needed pump and belt from PartSelect.com, not their problem. Even though I purchased two items that were not required, the cost was still half of what Sears wanted to charge me for a repair that would not have fixed the problem. I will certainly continue to use and recommend PartSelect.com.

Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, began pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.

Our Maytag (A308) washer is now about 29 yrs old. I put in a PartSelect water valve 3 yrs ago. When it started leaking recently I found the cuplrit to be a flexible hose to the outer basis. The front came off easily (two screws at the bottom) and the hose clamps required some cleaning. I recommend purchasing new clamps. Under 30 minutes to get it running again.

My husband took the old water inlet valve off, and put the new one on, and it works great. Very easy to replace.

Unplug from electrical outlet.Unscrewed control panel and laid it open. The switch is in 2 parts. Removed wires and unscrewed each switch. Put wires back on and tightened switch back to mounting plate. No brainer. Tried washer and worked perfectly. Two tips: Check fuse on plate to make sure it isn't burned out before ordering any parts. Secondly when installing if you have older model washer there is a nib that sticks up on mounting plate that keeps the switch from installing correctly. Cut this nib off with a wire cutter and then install. The directions don't mention that.

First closed hot & cold water faucets feeding the two washer water hoses, then turned the machine on fill momentarily to bleed off water pressure in hoses, and unplugged power cord. Used pliers to help break seal on brass hose ends, removed old hoses. Removed 1/4 & 5/16 sheet metal screws, replaced leaky valves. New assembly was EATON Made in USA, high quality. Replaced rusted outlet hose spring clamp with "IDEAL" stainless screw clamp. Replaced unit in machine, installed new hoses, runs fine.

opened front of washer, removed motor, replaced glides and springs, installed motor and replaced belts. Installed new hoses and vacuum breaker. Its been a week now and no leaks or other problems.

Removed top. Removed agitator and tubs . Replaced seals and reassembled.

Easily

I removed the lid switch assembly and replaced it with the new lid switch assembly. The assembly included the lid switch, lid. check switch, and fuse. It came as one complete part.

I removed the top cover that has the controls .Then started to voltage check the circuit (diagram was inside top cover) starting from L1 (had power cord pluged in) noted power was not going through the Check switch after tapping on the switch it started to work. the switch was intermitent so replaced with a new one from your company. works good now .Greg Gran

Removed tubs per prescribed videos. Removed transmission per video. Disassembled transmission per video. Used heat and penetrating oil to free top shaft. Lubricated top shaft and bushings with grease and reinstalled. Reassembled washer with replacement parts from partselect. Problem solved. My wife loves this washer. It lasted 30 years before I had issues, many of the internals looked brand new. They dont make' m like this anymore. With the self- help videos, and OEM parts from partselect, I'll get another 30, Thank you so much.

Had to look up how to pop the front panel off the washing machine - that was the hardest part. Once that was off, the top unbolted and the cover came off the back of the control panel with a few screws. Tilting the washer-top back, I was able to clip the new upper and lower injector (attached to each other in advance) to the washing machine. Then I realized that I needed to clamp the water line to the injector FIRST - so I found a small screw clamp and attached the water line. One screw and one plastic tab hold the injector in place. Everything went back together fine and worked great! Maytag washer keeps on truckin for another ten years!

well i first put on 2 new belts because they were worn and smoking. the new belts did not fix the problem. you suggested putting in a new pulley. it went against my better judgement that the pulley was defective. well i put in the new pulley and now the real problem has surfaced. the transmission is not working. now i want to order a new tranny and low and behold it is no longer available. well why did you sell me a $99 pulley when that was not the next part to change after the belts were replaced. now i have a new pulley on a washer that is going to the recycle center as metal trash. well on my part i will reward maytag by buying a ge washer now. plus i will not count on using you as my parts supplier.

Remove the power cord and water hoses. Lay the machine on the floor. Remove two belts (washing and pumping). Unlock the screw of pulley using a hex key. Remove the broken pulley from the motor. Place in the new pulley. Lock the screw of the pulley. Install two belts. Turn the machine vertically. Plug in water hoses and power cord. Level the machine.