59679543014 Kenmore Refrigerator - Instructions

Pretty simple, remove the pantry lid, drawers above glass pantry cover and then the glass cover and its metal supports.
Then the pantry tray from its metal slides.
Remove the slides then the broken end cap.
The slides and end caps are attached with 1/4 inch hex drive screws.
I did notice a small change in the new end caps which will improve the
strength of the problem tab. I do not expect the same problem again.

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now

Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.

I did exactly what the email I got said to do: remove the 2 crisper drawers, remove the glass directly above the crisper drawers, drop in the center rail. It worked just GREAT! Thanks a bunch!

the only thing easier than installing the part was finding it on this website.
10 minutes max start to finish.

Removed the 2 fruit & veggie drawers & deli drawer and glass top. Nut driver to remove the side end cap. Remove and replace the rails onto the replacement part and reattach. Simple.

It had been broken for months and I just kept putting off calling a serviceman. Boy am I glad I found your site. I don't even want to think about what this may have cost. When the kids break something else I'll be ready !!

Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

First I removed the two vegetable bins. I then removed the glas top shelf from the pantry and removed the pantry drawer. There were 3 screws that held the pantry end cap to the interior of the refrigerator. I removed the three screws. I then lifted up the front end of the end cap allowing it to snap free. I then snapped the new end cap in place and reinstalled the screws. The rest was just reversiing the drawer installations.

Removed three screws and removed endcap LH and screwed sliding shelf bar two new endcap and reinstalled end cap in ref.

replaced the part with a new part from partselect. No tools were required

Couldn't have been easier. The missus dropped a cabbage on the draw cover, that broke off the knob that holds the drawer cover in place. Doh, this is a fairly new fridge and having to live with a drawer, missing the cover, just didn't work for me. I went on line and found parts select. Withing 10 mins the part I needed was on order, 3 days later I had the part and 15 minutes after that it was installed and the fridge was back together. Couldn't have gone better!

Center rail, very easy to install. Be careful removing the glass shelf.

The right side deli bin track was pretty easy as well. Study the broken part to see how the slider fits on the track and the back side of the refrigerator. Best surprise was the prices. I thought these parts would be harder to find and more expensive.

removed the two veggie draws, then the glass top, then the pantry draw...remove three screws. remove the temp adjustment lever and install on new end cap. install end cap and draws etc...took about 15 min.

remove and replace....

remove meat drawer and both crispers, then the shelf below the crispers pull the 2 screws that hold the drawer slide . remove the 3 screws that hold the pantry end cap on, replace it and reverse the operation

First I bought the wrong size left end cap. Then I bought the correct one. Measure and check the size first, learn from my mistake! This is the french door Refrigerator with the freezer on the bottom. So first remove the lift up door and the slide out drawer that is held up by the left end cap. Then, take out the two drawers, the glass shelve and the two front and back brackets that hold up the glass shelf. Then remove the three screws and when they are removed put straight up on the front of the the end cap to release the slide on hold in the very front. When replacing insert the two back tabs and slide onto the hold in the front. Do not over tighten the 3 screws and then replace the two bars, the glass, and the two drawers.