4KAED4900FW0 Admiral Dryer - Overview

Sections of the 4KAED4900FW0

[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Multi Rib Belt - 92-1/4" – Part Number: 341241
Multi Rib Belt - 92-1/4"
★★★★★
★★★★★
(381)
PartSelect #: PS346995
Manufacturer #: 341241
This dryer drum belt (Whirlpool Dryer Belt, Drive Belt) has four ridges, three grooves and is 1/4" wide, and 92 1/4 inches in length. It comes in black and is made of rubber. The belt transfers the ro...
$17.17
  In Stock
Dryer High Limit Thermostat – Part Number: WP3977767
Dryer High Limit Thermostat
★★★★★
★★★★★
(28)
PartSelect #: PS11742185
Manufacturer #: WP3977767
A dryer high-limit thermostat (High Limit Thermostat, Hi-Limit Thermostat, Dryer High-Limit Thermostat) is a switch that is actuated by temperature change. This high limit thermostat acts as a safety ...
$23.49
  In Stock
Dryer Door Handle - White – Part Number: W10861225
Dryer Door Handle - White
★★★★★
★★★★★
(317)
PartSelect #: PS11731583
Manufacturer #: W10861225
This white OEM dryer door handle is used to open and close the dryer's door. Comprised of plastic and 6-by-2-inches in dimension, the handle is sold individually and attaches to the dryer door. Your d...
$38.55
  In Stock
Roller Support Tri-Ring – Part Number: WPW10512946
Roller Support Tri-Ring
★★★★★
★★★★★
(5)
PartSelect #: PS11755850
Manufacturer #: WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
$13.41
  In Stock
Leveling Foot – Part Number: 49621
Leveling Foot
★★★★★
★★★★★
(13)
PartSelect #: PS1609293
Manufacturer #: 49621
If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so...
$11.37
  In Stock
Dryer Lint Screen Filter – Part Number: WPW10717210
Dryer Lint Screen Filter
★★★★★
★★★★★
(145)
PartSelect #: PS11757278
Manufacturer #: WPW10717210
This manufacturer-certified dryer lint filter is used to collect lint during the dryer cycle, to prevent damage to the machine and to prevent lint from sticking to clothes. This model comes in white a...
$46.46
  In Stock
Heating Element Connection Wire Kit – Part Number: 279457
Heating Element Connection Wire Kit
★★★★★
★★★★★
(3)
PartSelect #: PS334206
Manufacturer #: 279457
This kit is used for electric clothes dryers, and it comes with a yellow wire nut.
$11.05
  In Stock
Screw, 8/18 x 3/8 – Part Number: WP90767
Screw, 8/18 x 3/8
★★★★★
★★★★★
(2)
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.41
  In Stock
Dryer Blower wheel – Part Number: WP694089
Dryer Blower wheel
★★★★★
★★★★★
(18)
PartSelect #: PS11743785
Manufacturer #: WP694089
The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance. The blower wheel spins on the motor shaft to blow air through the dryer drum and out through the exhaust.
$36.60
  In Stock
Timer – Part Number: WPW10185982
Timer
★★★★★
★★★★★
(36)
PartSelect #: PS11749831
Manufacturer #: WPW10185982
This dryer timer is used to control the unit's cycles by regulating the length of time that power is directed to each setting.
$113.19
  In Stock
Lint Trap Housing Seal – Part Number: WP339956
Lint Trap Housing Seal
★★★★★
★★★★★
(8)
PartSelect #: PS11741506
Manufacturer #: WP339956
This is foam seal for your dryer. It forms a seal to prevent air from escaping the rear of the dryer drum and the lint duct. This model comes with adhesive backing and is located in between the lint c...
$9.75
  In Stock
Two-Piece Split Ring Bearing – Part Number: 279441
Two-Piece Split Ring Bearing
★★★★★
★★★★★
(10)
PartSelect #: PS334199
Manufacturer #: 279441
This is a replacement bearing ring kit for your dryer. The bearing rings are found on the top and bottom lips of the dryer drum. If your dryer is unusually noisy, or the drum will not turn during oper...
$58.67
  In Stock

Questions And Answers for 4KAED4900FW0

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the 4KAED4900FW0

[Viewing 11 of 11]
Noisy
Fixed by
these parts
Fixing Fixing Fixing
Show All
Drum Not Spinning
Fixed by
these parts
Fixing
Show All
Door won’t close
Fixed by
these parts
Fixing Fixing Fixing
Show All
Too hot
Fixed by
these parts
Fixing Fixing Fixing
Show All
Not Heating
Fixed by
these parts
Fixing Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing Fixing Fixing
Show All
Timer Not Working
Fixed by
these parts
Fixing
Show All
Heat stays on after drum has stopped
Fixed by
these parts
Fixing
Show All
Leaking
Fixed by
these parts
Fixing
Show All
Won’t Start
Fixed by
these parts
Fixing
Show All
Touchpad does not respond
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broken tumbler belt
1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall when it loses support)
6. Removed broken belt and lint from interior parts; removed tensioner (which had fallen out of place). Note: The newer models have a tensioner pulley; my older model had a smooth semicircle that was confusing at first glance
7. Flipped dryer onto its back (for easier reinsertion of new belt and tumbler)
8. Placed new belt on tumbler; reinserted tumbler
9. Inserted new belt through tensioner, inserted tensioner "legs" into grooves on floor. Note: The belt will pull the tensioner upright when it's inserted properly (which isn't obvious at first)
10. Made sure belt and tumbler seal were properly installed
11. Replaced parts in reverse order
The process took over an hour because I couldn't figure out how to insert the belt through the tensioner. The trick is to insert the folded belt through the tensioner and onto the motor pulley. If I had to do it again, it would take about 30 minutes (including cleaning lint)
Parts Used:
Multi Rib Belt - 92-1/4"
  • Michael from San Antonio, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench set
138 of 158 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bought motor, then bought blower wheel also
couldn't get blower wheel off of the motor. really tight. rounded off the wheel's square hub while trying to hold it still as I turned the motor shaft out. No, I wasn't turning it the wrong way :) I ended up going to the back of the dryer and using the multimax to quickly cut the wheel away from the hub. I love that oscillating saw! Just for fun, I put the motor in a bench vise and got the wheel hub off (in pieces). VERY tight! Ordered new wheel, and the job was smooth sailing from there on. I am guessing that experienced repair people automatically order the motor and blower wheel at the same time(?) BTW both parts were perfect matches for the originals. Not surprised; this has always been my experience with partselect.com!
Parts Used:
Dryer Blower wheel
  • Daniel from Coatesville, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
94 of 110 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken belt - drum would not turn
Started out taking the back off, then found online that access is from the front and much easier to get to. Simply pop the hinges in the back of the top panel and then the front of the top is popped off. From there, it is easy to remove the old belt, clean the innards (found 31 cents) and replace the new belt. It was a little disconcerting to see the idler pulley laying loose inside, but the diagram showed exactly how to put it back in place, with the new belt keeping it in place.
Parts Used:
Multi Rib Belt - 92-1/4"
  • Gary from Oakland, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
82 of 96 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!