40648127 General Electric Dishwasher - Instructions

Unscrewed 2 screws from under the counter, pulled out dishwasher. Saw where it was leaking. Took wires loose, took the rack out, unscrew the white mesh, took out the dishwasher sump housing product saw a crack and ordered the piece. For anyone out there make sure you turn the electric power switch off before you attempt to fix anything!!!!!!

After disconnecting the supply and drain hoses I unscrewed the security screws and slid the unit out of it's space under the counter. I tipped the machine about 30-45 degrees to one side and examined the underside. I noticed a solenoid that appeared to control a valve leading to the drain tube. I cycled the washer through a wash cycle and noticed that the solenoid never activated. I removed the solenoid and found it filled with debris. I cleaned it out and reinstalled it, but it still did not function. I ordered the part from PartSelect.com because they had the clearest description of the part I needed. Delivery was quick and installation took only a few minutes. After hooking everything back up and sliding the machine back in place, it works like new.

It was tricky to get the old rack off. Usually you can unclip the clips closest to the front wheels to pull the rack out. However, there is an area behind one of the wheels that you can kind of release and than pull the rack out. You then have to slide out the funnel/fan piece from the middle. That piece slides/ snaps in the middle of the the new rack. Then slide the new rack in place, re attach the release used to slide oldrack out.
That is it !!

unscrewed bracket unplugged solenoid , pried off spring clip pulled nylon arm off and took off old push on nut. I had to squeeze the push on nut together with pliers from two angles to get it loose

Took off the lower faceplates. Removed the old eyelet assemblies (one broken, one not) and replaced both with new ones. Very easy to repair.

The leak was coming from the drain valve shaft and I found the tips to replace the seal from this website. I was able to reach everything without removing the dishwasher from the cabinet. Once I got the cam lifter off the old push on nut was corroded so it was easy to get off. The old seal was recessed so I used the point of an ice pick to gently pry it out. The new seal was easy to push in place but the push on nut was a bear. I saw other comments about using a deep socket to push it on but I didn't have one the right size. I was able to hold the end of the shaft with pliers and pushed the nut in place using a screwdriver. Ran a short cycle and no more leak. Thank goodness for this website. Found the part easily and the other written comments were very helpful.

Replaced with a new rinse aid fill cap.

Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff

Replaced all ordered parts.

Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell

Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed

I watched the video and did exactly what he did. I am a novice when it comes to repairs. I learn as I go. This repair went flawlessly. Ordering was quick and easy. The part arrived quickly. The repair took less time than expected. The part was what I needed and nothing else broke or went wrong when repairing the original problem. It was a 100% success.

Removed 4 screws, took off basket covering, put new part in one turn, then replaced covering. Plumber had come out, I watched what he did, he had to order part and come back. I asked how much he didn't know but said cheaper than buying a new dishwasher. When he left I started calling around about the little plastic part that I needed. Part was $15.50. They called and said it would be $110.00. Needless to say I called them out and ordered the part myself and put it in. Took me like 6 minutes and cost $21.69. I was so mad about this situation that I even got my service call money back that I had already paid.

Old baffles lift out and new ones installed - very easy

I simply removed the front toe kick panels.
The solonoid is staring you in the face.
I removed the small nuts on back side of the solonoid bracket and removed the retaining clip and springs.
I installed the new solonoid and was very surprised how easy it was.

I DID turn the power OFF at the breaker panel prior to starting the repair.