3LMVWC400YW3 Maytag Washer - Instructions

ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned it back up and got caught up on laundry. good day when the washer is fixed.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Easy, just followed the repair video. Recommend also ordering the drive belt. Bought one locally during my repair.

Changing the gear case is a basic R and R operation since the gear case is a complete assembly riveted together. It is a bit challenging though getting to it because you have to totally disassemble the entire washer nearly every nut, bolt and screw. Fortunately the washer is fairly easy to work on and I am very mechanically inclined, but I did cheat a bit by watching some U-tube videos first. I couldn't find the same exact model washer as mine on U-tube but there were enough similar units to obtain the basic procedure. A thing I do when disassembling things is to take pictures of the way it's put together before removing stuff. It goes without saying that you first have to disconnect the power, the water hoses and it helps to get the washer out away from the wall so you can work around it. You have to remove the top, back panels, and the inner and outer tubs first. After removing the inner and outer tubs I turned the washer upside down in order to gain access to the gear case so I wouldn't have to stand on my head or lay down. Remove everything attached to the gear case (take picture) and use a strap wrench (or a strong friend) to hold the large pulley while removing the retaining nut. To remove the condenser (large round thing in black plastic retainer) rotate it counter clockwise and lift out, it doesn't snap out. I was very happy to see that the new gear case came with the shaft seal already installed so with a small amount of liquid dish soap around the outside of the rubber it allowed a nice slip fit back into the outer tub. All the parts that were removed pretty much will only fit one way so you don't have to worry too much about how everything goes back together. After reassembly and hooking up the washer again be sure to perform the calibration procedure before you turn on the water. Instructions came in the box with the gear case. Here is a side bar: I am 76, my grandson and I replaced the gear case in just a few hours, It's no big deal. Now for the interesting part, when I ordered the replacement gear case by the old part number I was told it had been superseded by a new number so when the new unit arrived I discovered that the shaft and seal looked different so hopefully the water leaking into bearing won't happen again. I was going to drill the old gear case apart and replace the bad bearing so I am glad I didn't because the shaft and seal would continue to leak and ruin the bearing again so don't try that. One thing I would like to mention about this company from which I ordered the part was the amazing delivery, only 36 hours. I ordered the part Sunday evening late and Tuesday morning early it arrived. Wow, blew me away, also I live in California and apparently the company is in Nova Scotia, no sales tax, Woo Hoo.

DO NOT do this repair from the top. The only thing needed to be removed from the top of the machine is the agitator and retaining clip. After removing these items, lay the machine on its front, on a table if you have a friend who will help. Remove the back cover. Simply disconnect the wiring, remove the water pump, the tub locking mechanism, the belt, and motor. Remove the four bolts holding the gearcase. It should come out with little effort. Remove the old tub seal. There should be a new one on the replacement. Lubricate the new seal. Dishwashing liquid worked great. Move the drive wheel from the old gearcase to the replacement part. All the parts originally removed will only fit one way. Reverse all the removal steps and you be should be ready to go. My only problem with the replacement was there was no groove in the new part spline for the tub retaining clip. Seemed to be no problem since the agitator is bolted on so the tub is going nowhere.

slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Removed old striker ( 2 Phillips head screws ) replaced with new striker with the 2 screws and was done, easy fix...

The video you sent me was very helpful told me the exact tools I needed and how to do it.
Thank you

Removed center cap, loosened center nut, pry lightly up on center plate and tap center nut. Center plate comes loose, remove nut, remove center plate. Pry lock clip out and remove, remove screw with electric impact (screw drive will work, but slower), remove drive hub. Install new drive hub (be sure to check screw hole alignment), install and tighten screws (be sure to follow a skip pattern and bring it down even), install lock clip, install center plate, install and tighten nut, replace center cap. Done!

Replaced the suspension rods.
Must be done on its side as the rods only pull down. There is no slot.

Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.

Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicates the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.

screw driver and a rachet and socket took it off and put the new one on . no problem follow the direction that comes with it .

My spin cycle was running, but spinning slowly and not drying my clothes. The agitator spun quickly like normal, but the basket did not spin fast. It seemed like something was slipping. I checked the belt, but it seemed fine and it was less than a year old. I was afraid that the transmission was going, but there wasn't any grinding sound of gears. Luckily the hub part description said that this could fix the slow Spin cycle. Over all the repair was easy, but pulling the agitator off was very difficult. I've got a strong grip and patience and after about 10 - 15 mintues of yanking on the agitator it came off. Don't try to use pliers as it will damage the plastic agitator. Replacing the hub drive and reassembly went very smoothly. The old hub drive wore out because it is plastic and connects to the metal drive shaft from the transmission. After years of torque, the hub will eventually strip out. Sooner depending on your usage and heavy duty cycles. In case you don't know, your machine might have the service manual in it on the inside of the body taped to the side. Mine helped me run through some troubleshooting steps and component tests to pinpoint to problem. Thanks Parts Select!

Actually, I "Youtubed" it. I entered the info from the washer and found what was similar. What would help is when you tilt the washer (on back or front) so you can look at what you're going to work on to match (or closely match) what is on Youtube. It is SO easy, it's unbelievable.