110C60242510 Kenmore Dryer - Instructions

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

I use the manentance kit that was not the problem. I end buying the drive motor and that was it. I was happy with the service I got from part select, overnight mail what more could I ask for? I am also glad I replace everthing with mainentance kit. Thank you for your help john degnan

After identfying that the problem was due to a damaged drum support roller, I decided to replace the bad roller instead of replacing the dyer itself.

The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing the belt from the motor pulley and tensioner, and then pulling the drum straight out.

At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.

Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.

(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)

just remove 4 screws removed the drum and put the affected part and that's it

I thought I had checked the arm piece of the rack real good for a product number on my original part but I missed the number till the 2nd box came in, and a looked real careful and realized it was the same as the order I thought was bad.
Put the spring arm in first and the rack will fit in the front groove.
It would have been good if there had been a picture of the dryer arm attached to the dryer.
So I have 2 good racks and will return one if you tell me where to send it.
Keith Walden..

I watched the video then called them to order parts. They were VERY helpful & NICE. I had the parts the NEXT day. I followed the video instructions & it worked. They made my day! THANK YOU JoAnn & Teresa!

Followed the instructions found online. Only thing I would add is that the clips are easier to work with if you warm them up a little before you try to install them.

Took dryer apart. Should've started with You tube videos so I took more apart than I needed.

Got all the parts I needed from Parts select.

Fixed it and works great.

Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.

The repair video provided for this model 110.97584810 gave erroneous info. It says to remove the back vent cover. The back on this model is not removable. I wasted an hour trying to remove back and top of dryer before discovering that the bottom front panel below the door pops off. Then the cover of the blower must be removed by removing two screws. The thermostat part can then be accessed and replaced as shown in the video. You'll need a 1/4" rachet to remove the screws as there isn't space to use a nut driver. Note that the statement in the video "This repair is done all from the back" is completely wrong. It is done entirely from the front. It can be done without even moving the dryer.

Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,

Your great service is very hard to find.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

I shorted the thermal cutout after removing the back.
I then ordered the thermal Cut-Off Kit from PartSelect.
While this was not my first order from them, I was still impressed with the ease and by how soon I received the part without any hassles or glitches. PartSelect will be my primary parts supplier from now on.

i took a stab that it was the thermostat,but it wasn't.after finding out it was the coils i purchased them and lifted the top of the dryer and undid two screws in the upper front of the dryer and lifted the front off all while holding the tub in place.The coils are located in the very front left of the dryer,i took the holder bracket off,disconnected the wires and replaced the coils(they just sit on a rod)dryer works like new and thanks to the new thermostat also gets hotter,i'm guessing that was next.

Replaced thermostat on back of dryer, very easy to do, took about 15 minutes after watching video . doe's not require rocket scientist to do.