110C60242510 Kenmore Dryer - Instructions

It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.

We had to pop open the top. Unscrew front of dryer from sides. Disconnecting the wires was a bit more difficult than expected. We had to use a tiny screwdriver to slide into the sides of the white wire connector on each side before pulling apart. Front drum falls when front of dryer is removed. It took two of us to reassemble - one to hold the drum while the other put the front on. Our problem turned out to be one wheel. We replaced both wheels and saved the rest of the parts. Hums along just fine.

I attempted to take the back panel off the dryer only to discover all I had to do (after removing 10 or so screws) is remove the lower base plate in the front of the dryer. I also had removed the door which turned out to be unnecessary. After removing a guard in front of the heating element (2 screws) I yanked the the element housing that contained the heating element and then disconnected the 6 wires. Using my first ever, newly bought multi meter for only $9.99 from Radio Shack, I turned the dial to the infinity section and check the element for continuency. I did this by touching the meter's two probes to the element's terminals were the wires connect. The element was fine. Then I checked the two sensors the same way. The sensor furtherest away from the element's terminals didn't have a constant signal so I assumed that that sensor was bad. Well, come to find out, one sensor is open and the other in closed... only when the temp. changes do they operate by opening and closing the current. By this time I had already ordered the part so it was too late. Surprisingly, the part came in 2 days. I ordered it Sunday night and i figured it would be sent out Monday but it was already in the air Monday morning... Great service! I replaced both sensors and the dryer works like it did when I first got it.

Ignor installation video. it is for a different model dryer. The part is not accessed from rear. It is accessed from the front panel. Disconnect power. Remove two screws below front panel with cross head screwdriver. Swing panel up until it releases. No need to disconnect wires just put front panel down beside the dryer. Thermostat located right in front on duct easy to identify since it has four leads. Remove wires with needle nose pliers. Remove thermostat with nut driver. Contacts are labeled but hard to read. Hold thermostat so the lead number 3 (the 3 will be upside down) is on the left. Connect blue wire. White wire to top. Purple wires to bottom and right. Reverse removal procedure and you are done.

just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!

pulled dryer away from wall took screws out of lint screen lift top removed 2 screws one on each side of front at top and removed front panel. pulled belt off drum removed drum rollers tension pulley and while i was at it pulled back cover off of heating element and blower blew everything out with air hose did a total cleaning installed everything in reverse. i was amazed how fast the parts came the dryer was only down 2 days and it runs like new even if it is 20 years old i highly recommend parts slect and i will use them in the future

unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mounted new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).

I followed disassembly directions found on youtube and replaced th two-piece ring bearing that was identified by a parts diagra fron PartSelect. The repair was easy. Fix time was about thirty mionutes.

removed the back housing of the dryer and located the thermal switch. unscrewed the old one, popped in the new one and whala! I was back in business!

put the back cover back on the dryer and pushed it back into place.

put the high limit in , plus the temperature , plus the exhaust switches

first i removed the back cover by removing the six 1/4 inch screws then i removed the wires to the thermal switch there were three of them and using an ohm meter i checked each one for continuity until i found the one that had an open circuit. i removed the two 1/4 inch screws holding it in place and replaced it with the new one.

Followed the included instructions in the Maintenance kit. Very easy to understand & follow. Only advice is to have an extra set of hands to assist in re-installing drum w/ the new belt. Entire disassembly & reassembly could be done w/ basic hand tools but went alot quicker using a cordless drill w/ a set of nut/screw driver bits.

Took the two screws holding the lint trap to top. Used a putty knife to loose the clips holding the top of the dryer up so it could be hindged up for access. Used a nut driver to remove the four screws hold the front door on. Removed the lower dust panel, just clips holding in on. Pull the dryer drum out along with the broken belt and old belt tensioner. Took shop vac and cleaned lint and removed about $2.00 of loose change from the base. Installed the new drum supper wheels. Held belt around drum to put back in. Looped the belt through tensioner and around motor drive pulley as shown in instructions. Put front door on only to find the felt around the door had slipped making the drum hard to turn. Pulled the door back off and laid the dryer on it's back before putting the door back on , so you can run your hand around the door to make sure the felt go inside the drum. Put the four screws back in the door panel before uprighting the dryer. Sucess the drum turned freely. Put other remaining panel and srews in lint trap . Hook the dryer back up to vent, power and gas, and turned on the dryer. Runs like new!

Disassembled dryer, removed tumbler, replaced drum support rollers

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working