Kenmore Washer Dryer Combo Motors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Kenmore Washer Dryer Combo Motors
Your Price
$21.45
In Stock
Kenmore Washer Dryer Combo Direct Drive Motor Coupling
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...
PartSelect Number PS1485646
Manufacturer Part Number 285753A
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft. It attaches to the direct-drive transmission and the motor shaft. If this part is defective it will affect the agitator in your washer because of its direct connection with the motor. Your washer may not agitate, spin slowly, or not spin at all. The coupling must be replaced when there is no longer a consistent connection between the transmission and the motor shaft. The coupling can wear over time because of its location between two major parts of the dryer. It is subject to material fatigue over time from normal use, or breakage caused by frequent overloading. The part measures approximately 2 inches in diameter, and is constructed of plastic and metal. This model comes in black/white.
Fixes these symptoms
- Burning smell
- Draining Issues
- Leaking
- See more...
Installation Instructions
Jeff from Wayne, NJ
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...
Your Price
$97.46
In Stock
Kenmore Washer Dryer Combo Drive Motor With Pulley
1) Removed back - 6 screws
2) Removed dryer vent - 2 screws on top, 3 on bottom
3) Popped the top open
4) Removed Front of dryer cabinet - 2 screws
5) Removed Belt
6) Removed Drum
7) Cleaned up all lint
8) Pop off motor retainers front and back
Here is the tricky part for me.
9) Removed vent fan on back of motor.
I did not know that the back of the fan was square, and you could put an open ended wrench on it to hold it while you also have a vice grip on the front motor shaft. Then its a simple left to loosey operation. I first tryed to turn the fan blade to take it off, but proved to be to tight.
10) Repeat backwards to reassemble
While I had it apart I also replaced the Drum support rollers & Installed a new belt. Not that diffucult of a repair Good Luck, was certainly better than buying a new one at + $300.00 at Black Friday rates. Read more...
PartSelect Number PS334304
Manufacturer Part Number 279827
This OEM drive motor is designed to operate the drum in electric and gas dryers by turning the drive belt, enabling proper rotation during drying cycles. Compatible with most Whirlpool-incorporated dryer brands manufactured before 1996, it includes a pre-attached pulley, which is not available separately. If the motor has shorted out or failed, the drum will no longer spin, and replacement is necessary to restore full functionality. Installation requires disconnecting the dryer from its power source before removing the old motor and installing the new one. This component is sold individually and meets original equipment standards for performance and reliability.
Fixes these symptoms
- Drum Not Spinning
- Noisy
- Will Not Start
- See more...
Installation Instructions
Mark from Fremont, NE
Wife told me Dryer would make a funny sound, then stop + had an a funny smell as well. The Electric motor that drove the unit was overheating and locking up, It was time to be replace.
The best part of my repair was I had everything back in service in 3 days. And one of these days was to consider just buying a new dryer. Had parts overnited and all parts fit and easy to replace.1) Removed back - 6 screws
2) Removed dryer vent - 2 screws on top, 3 on bottom
3) Popped the top open
4) Removed Front of dryer cabinet - 2 screws
5) Removed Belt
6) Removed Drum
7) Cleaned up all lint
8) Pop off motor retainers front and back
Here is the tricky part for me.
9) Removed vent fan on back of motor.
I did not know that the back of the fan was square, and you could put an open ended wrench on it to hold it while you also have a vice grip on the front motor shaft. Then its a simple left to loosey operation. I first tryed to turn the fan blade to take it off, but proved to be to tight.
10) Repeat backwards to reassemble
While I had it apart I also replaced the Drum support rollers & Installed a new belt. Not that diffucult of a repair Good Luck, was certainly better than buying a new one at + $300.00 at Black Friday rates. Read more...
Your Price
$158.79
In Stock
Kenmore Washer Dryer Combo Washer 2speed Drive Motor 60hz 120v
PartSelect Number PS11743427
Manufacturer Part Number WP661600
This is a 2-speed drive motor for your washing machine. The motor rotates the spin basket when the washing machine is in spin or tumbling mode. You will likely need to replace the motor if you are experiencing burning smells or your washer will not start. The tools you will need to make this repair include a number two Phillips screwdriver, a flat-blade screwdriver, and a 5/16 nut driver.
Fixes these symptoms
- Burning smell
- Spinning Issues
- Will not agitate
- See more...
Installation Instructions
Lowell from Dover, DE
Washer had water leak in lower front and would not drain.
Laid the washer on its back and found leak in water pump. Found out it was caused by vibration from motor with bad bearing. Removed pump and motor which were held on by clips. Both were removed and replaced without removing cabinet from machine.
Read more...
Your Price
$170.86
In Stock
Kenmore Washer Dryer Combo Drive Motor With Threaded Shaft - 120v 60hz
I input the number into the search box and there was the exact motor I needed.
The price was fair and the delivery quick so I figured I would give yuo guys a shot and see how it goes.
The part showed up on time and as expected. It was well packed and most importantly - it was the CORRECT part.
I disassembled the dryer which involved removing the lint trap, pulling out the blower fan and removing the motor cover. The motor was held in with 2 metal screws and wiring harness.
I took the belt off of the tensioner and pulled out the old motor. The motor was mounted with 2 clips which snapped off with ease. Reassembly was a breeze since the motor fit perfectly- the entire transplant operation took all of about 35 minutes.
I crossed my fingers, turned on the gas, plugged it in and........SUCCESS!
Since the dryer was down for over a week the backlog of laundry was piled pretty high. This replacement motor would immediately be put to the test.
It has been 5 days of non-stop drying and no squeeks, no squeels and nothing but dry clothes!
Thanks to Part Select for getting everything right the first time. It made a potentially very bad experience turn out as good as I could have ever hoped. Read more...
PartSelect Number PS334287
Manufacturer Part Number 279787
The blower shaft is 1-5/8 inches long, while the drive shaft is 1-1/4 inches long.
Fixes these symptoms
- Drum Not Spinning
- Noisy
- Won’t Start
- See more...
Installation Instructions
Kelly from Aptos, CA
Our dryer started squealing and would then stop running.
After determining that the dryer motor was the issue I wrote down the part number and logged on to partselect.com.I input the number into the search box and there was the exact motor I needed.
The price was fair and the delivery quick so I figured I would give yuo guys a shot and see how it goes.
The part showed up on time and as expected. It was well packed and most importantly - it was the CORRECT part.
I disassembled the dryer which involved removing the lint trap, pulling out the blower fan and removing the motor cover. The motor was held in with 2 metal screws and wiring harness.
I took the belt off of the tensioner and pulled out the old motor. The motor was mounted with 2 clips which snapped off with ease. Reassembly was a breeze since the motor fit perfectly- the entire transplant operation took all of about 35 minutes.
I crossed my fingers, turned on the gas, plugged it in and........SUCCESS!
Since the dryer was down for over a week the backlog of laundry was piled pretty high. This replacement motor would immediately be put to the test.
It has been 5 days of non-stop drying and no squeeks, no squeels and nothing but dry clothes!
Thanks to Part Select for getting everything right the first time. It made a potentially very bad experience turn out as good as I could have ever hoped. Read more...
Your Price
$166.33
Special Order
Kenmore Washer Dryer Combo Motor
PartSelect Number PS12584805
Manufacturer Part Number 134196602
This dryer drive motor is a key component in washer/dryer combo units, responsible for rotating both the drum and blower wheel to facilitate efficient drying. It features dual shafts—one driving the drum via a belt and the other powering the blower wheel to circulate air throughout the appliance. Designed for durability and consistent performance, this motor helps maintain proper airflow and tumbling action, ensuring clothes dry evenly. Common symptoms of a failing motor include a drum that won’t turn, poor drying results, or unusual noises during operation. Compatible with select Frigidaire, Electrolux, White Westinghouse, and Kenmore models, this genuine OEM part should be installed with the power disconnected to ensure safety.
Your Price
$173.86
In Stock
Kenmore Washer Dryer Combo Drive Motor And Pulley
PartSelect Number PS11699355
Manufacturer Part Number WE17X22217
Unleash the full power of your GE dryer with this highly efficient Drive Motor and Pulley. It's designed to ensure a consistent and smooth operation of your dryer drum. When replacing this motor, please be mindful to inspect for a non-operational door switch on gas dryers and a problematic thermal limiter device or door switch on electric dryers. The kit comes complete with a wiring harness, carefully encased in Styrofoam for protection, and an informative instruction sheet. Make the most out of your home appliances with quality parts from GE.
Installation Instructions
Darryl from FARR WEST, UT
Bad dryer motor
Replaced dryer motor which was a perfect fit thanks to your help. The process was helped by the internet videos available for the step by step procedure of taking the dryer apart and replacing the bad motor. I also was able to completely clean the inside of the dryer thoroughly, and reassemble it back together .
Read more...
Your Price
$192.07
In Stock
Kenmore Washer Dryer Combo Remote Style Pump With Motor
PartSelect Number PS417325
Manufacturer Part Number 131268401
Use this with either a top load or front load washer. This pump has an horizontal mount.
Fixes these symptoms
- Leaking
- Will not drain
- See more...
Installation Instructions
Thomas from Walpole, MA
Pump Motor Failed
First, remove the 2 screws that hold the lower front cover in place, remove the cover and disconnect the plug and the ground wires from the pump. Next attach the washing machine drain hose to a wet vac, since even if the machine is empty, there will still be water in the outer tub and the pump. Suck the whole thing dry, remove the 2 bolts that hold the cover onto the pump, use a pliers to remove the 2 hose clamps, remove the hoses (no mess because of the vacuum). Remove the 2 screws that hold the pump to the base of the washer and remove the pump. Save the mounting bracket from the bottom of the pump. Orient the outlet on the new pump to match your old one if needed, instructions to do this are included with the new pump. Install the mounting bracket onto the new pump. Mount the pump to the washing machine base, reconnect the hoses, the cover and the wiring. Put the drain hose back into your drain. Run the machine, check for function and leaks. If all is well, replace the lower cover. Don't forget to tell your wife that the job was a whole lot harder than it looked.
Read more...
Your Price
$218.85
In Stock
Kenmore Washer Dryer Combo Drive Motor With Switch
PartSelect Number PS334297
Manufacturer Part Number 279811
This drive motor is designed to power the drum in select dryer models, ensuring smooth rotation and consistent performance. If your dryer drum isn’t spinning or is making unusual noises, a faulty motor may be the cause. Replacing the motor can restore proper function and reduce noise during operation. This component is engineered for compatibility with specific units and should be installed with the appliance unplugged to ensure safety.
Your Price
$192.97
In Stock
Kenmore Washer Dryer Combo Motor Assembly
PartSelect Number PS12585125
Manufacturer Part Number 5304515840
This washer drive motor assembly is the primary power component responsible for the mechanical operation of the washing machine section in a stacked laundry unit. It drives both agitation during the wash cycle and high-speed rotation of the spin basket to extract water from clothing during the spin cycle. Constructed with durable metal and alloy steel components, the motor is designed to handle repeated loads and continuous operation while maintaining reliable performance. A failing drive motor may cause the washer to stop agitating, fail to spin, or experience a complete loss of drum movement during a cycle. Replacing the motor assembly can restore proper wash and spin function, helping return the washer to normal, efficient operation.
Your Price
$234.57
In Stock
Kenmore Washer Dryer Combo Drive Motor
PartSelect Number PS10061527
Manufacturer Part Number WH49X20495
Let's help get your refrigerator back to its top-notch cooling performance with the GE Condenser Fan Motor. This is a vital part of your refrigerator, designed to keep your food fresh and prevent spoilage by managing your appliance's cooling system. You might not notice it, but this mighty part is always working behind the scenes. It powers the fan blade that moves air across the condenser coil - this is what enables your refrigerator to maintain its cool interior temperature. When the motor is in tip-top shape, your refrigerator functions properly and efficiently. Important to note: before you start the replacement process, be sure to disconnect your refrigerator and safely store any perishables?safety comes first. And, while you're at it, put on a pair of work gloves to protect your hands. Choose the GE Condenser Fan Motor as your go-to solution for boosting your refrigerator's performance. It?s an investment for a happier, fresher kitchen. This motor is designed to work seamlessly with GE refrigerator, offering trusted quality, and assured compatibility. Experience the difference with the GE Condenser Fan Motor - for a refrigerator that works as good as new.
Related Kenmore Washer Dryer Combo Parts
- All Kenmore Washer Dryer Combo parts
- Kenmore Washer Dryer Combo Agitators
- Kenmore Washer Dryer Combo Bearings
- Kenmore Washer Dryer Combo Belts
- Kenmore Washer Dryer Combo Brackets and Flanges
- Kenmore Washer Dryer Combo Caps and Lids
- Kenmore Washer Dryer Combo Circuit Boards and Touch Pads
- Kenmore Washer Dryer Combo Dispensers
- Kenmore Washer Dryer Combo Doors
- Kenmore Washer Dryer Combo Drums and Tubs
- Kenmore Washer Dryer Combo Ducts and Vents
- Kenmore Washer Dryer Combo Elements and Burners
- Kenmore Washer Dryer Combo Filters
- Kenmore Washer Dryer Combo Fuses
- Kenmore Washer Dryer Combo Handles
- Kenmore Washer Dryer Combo Hardware
- Kenmore Washer Dryer Combo Hinges
- Kenmore Washer Dryer Combo Hoses and Tubes
- Kenmore Washer Dryer Combo Knobs
- Kenmore Washer Dryer Combo Latches
- Kenmore Washer Dryer Combo Legs and Feet
- Kenmore Washer Dryer Combo Lights and Bulbs
- Kenmore Washer Dryer Combo Panels
- Kenmore Washer Dryer Combo Pulleys
- Kenmore Washer Dryer Combo Seals and Gaskets
- Kenmore Washer Dryer Combo Sensors
- Kenmore Washer Dryer Combo Springs and Shock Absorbers
- Kenmore Washer Dryer Combo Switches
- Kenmore Washer Dryer Combo Thermostats
- Kenmore Washer Dryer Combo Timers
- Kenmore Washer Dryer Combo Transmissions and Clutches
- Kenmore Washer Dryer Combo Valves
- Kenmore Washer Dryer Combo Wheels and Rollers
- Kenmore Washer Dryer Combo Wire Plugs and Connectors