Kenmore Washer Dryer Combo Seals and Gaskets
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Kenmore Washer Dryer Combo Seals and Gaskets
Your Price
$42.81
In Stock
Kenmore Washer Dryer Combo Duct Felt Seal
PartSelect Number PS12722961
Manufacturer Part Number WE09X27634
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromised. Disconnect power to the dryer before completing this repair. You will need to remove the front of the dryer to gain access to the felt seal. This felt seal may differ in appearance from your original but will function the same as your original. This is an OEM replacement part that is sourced directly from the authentic manufacturer.
Fixes these symptoms
- Drum Not Spinning
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Matthew from Plainfield, IL
Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy.
Read more...
Your Price
$45.29
In Stock
Kenmore Washer Dryer Combo Dryer Drum Seal With Adhesive
PartSelect Number PS970088
Manufacturer Part Number 280114
This drum seal with a silicone rubber adhesive is used in dryers. This part seals the drum to make sure air does not escape from the dryer. If your dryer is making loud noises, is not producing enough heat, or no heat at all, or there are marks left on your clothes, replacing the seal on your dryer can solve the problem. The tools needed for this installation project are: 1/4 inch nut driver, Phillips screwdriver, small flat blade screwdriver, and putty knife. Remember to unplug your dryer from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for installation instructions.
Fixes these symptoms
- Drum Not Spinning
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Jerry from Everett, WA
Rear tub seal failure
I removed the top cover and then the back cover, released the belt tensioner and removed the drive belt. Then slid the tub out of the unit and onto the back dack. Sanded the remnents of the old seal off. Wiped the tub lip with laquer thinner and applied the "fast" drying glue supplied with the kit. Installed the seal and re-assembled the unit...works fine
Read more...
Your Price
$9.62
In Stock
Kenmore Washer Dryer Combo Dryer Lint Trap Housing Seal
PartSelect Number PS11741506
Manufacturer Part Number WP339956
This is foam seal for your dryer. It forms a seal to prevent air from escaping the rear of the dryer drum and the lint duct. This model comes with adhesive backing and is located in between the lint chute and the bulkhead of your appliance. This foam seal is just over 28 inches long and under 1 inch wide. You may need to replace this part if your clothing is taking too long to dry, or if your dryer is not generating enough heat or no heat at all.
Fixes these symptoms
- Noisy
- Not Heating
- Too hot
- See more...
Installation Instructions
Eric from Fort Dodge, IA
dryer drum not turning and no air circulating
replaced motor and drum rear seal as well as idler wheels, the old rear drum seal was completly worn out, since I had it all apart, I replaced lint chute and trap seals and belt and tensioner. I spent less money on parts than if I would have bought a new dryer. The motor was the main problem as the bearings were shot.
Read more...
Your Price
$7.47
In Stock
Kenmore Washer Dryer Combo Centerpost Gasket
PartSelect Number PS11723081
Manufacturer Part Number W10814296
This part may also be referred to as a main outer tub seal. This part prevents leaking from the bottom of the tub. The gasket is approximately 2 inches in diameter to the outer edge, black in color, and made of plastic material. To perform this repair, you will need to disconnect the power, drain hose, and the inlet hose. You will need to remove the entire outside cabinet to have access to the tub assembly. The tub will need to be removed entirely. This is a genuine part that is sourced directly from the manufacturer.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Dexter from Milwaukie, OR
Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose
After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go.
Read more...
Your Price
$46.01
Special Order
Kenmore Washer Dryer Combo Front Lower Drum Seal
Replacing the belt was a very good idea, though as mentioned, the drum support bearing is just a "nice to do" - not necessary, but it gives you the excuse to re-grease it (I used a thick Molly impregnated grease from my motorcycle).
The only other advice I can give is that I used a chisel to scrape off the old felt - it came off in very little time, and I didn't end up needing to really do much cleaning of the drum afterwards. Just use a sharp one you're not afraid to dull - it'll be metal-on-metal contact.
Using the spring-loaded clamps that you can get from the hardware store was also a huge help - it just needs to keep the upper glide stuck to the drum for the 30 minutes for the glue to cure - I used 6, but 3 would work. The bottom seal doesn't need them as the felt will tend to stick to the drum when the glue is applied.
You might not NEED to replace the lower seal, but I'd suggest it. It's cheap enough, and this job is "not fun" enough that it only adds a few minutes total - good insurance that you do a complete job.
You also might want to get some aluminum foil tape and re-tape your blower extension tube - mine was ripped off from moving from house to house over the years. Read more...
PartSelect Number PS460194
Manufacturer Part Number 5303283286
The front lower drum seal is used in the assembly of dryers. This seal helps keep your appliance running quietly. It allows the drum to smoothly rotate on the front panel. If you notice brown marks on your clothing, if the dry cycle is taking long, or if there are unusually loud noises, the seal might be worn down. If that is the case, you will need to replace the seal. This replacement part is made out of felt. The high temperature adhesive required to install this seal is sold separately. Before you begin any repair work, make sure the appliance has been unplugged.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Dan from Portland, OR
Brown spots on clothing
I was getting brown spots on my clothing since I bought this used dryer. Went to partselect.com Fine with me, but not my wife and daughter! Anyway, after ruling out rust, I ended up here and found Randy's story - without it, I'd be lost! Basically, the felt seal crushes over time, and clothing gets caught in the gap stuck against this nasty old brown felt and leaves a mark.Replacing the belt was a very good idea, though as mentioned, the drum support bearing is just a "nice to do" - not necessary, but it gives you the excuse to re-grease it (I used a thick Molly impregnated grease from my motorcycle).
The only other advice I can give is that I used a chisel to scrape off the old felt - it came off in very little time, and I didn't end up needing to really do much cleaning of the drum afterwards. Just use a sharp one you're not afraid to dull - it'll be metal-on-metal contact.
Using the spring-loaded clamps that you can get from the hardware store was also a huge help - it just needs to keep the upper glide stuck to the drum for the 30 minutes for the glue to cure - I used 6, but 3 would work. The bottom seal doesn't need them as the felt will tend to stick to the drum when the glue is applied.
You might not NEED to replace the lower seal, but I'd suggest it. It's cheap enough, and this job is "not fun" enough that it only adds a few minutes total - good insurance that you do a complete job.
You also might want to get some aluminum foil tape and re-tape your blower extension tube - mine was ripped off from moving from house to house over the years. Read more...
Your Price
$31.58
In Stock
Kenmore Washer Dryer Combo Lower Front Felt Seal With Adhesive
First, unplug the dryer. Then, open the top so that you can get access to the work area. On each side of the inside front, there is a screw that connects the front panel to the side panels. Unscrew those screws and pull the front panel until it disconnects from the side panels. Be careful as there are wires that are secured to the bottom of the top inside lip of the front panel. One set of wires goes to the light bulb in the dryer door. You don't need to disconnect the wires, but be sure you don't damage the wires by pulling the front panel too far away from the dryer.
Once you have the front panel out of the way, you can see the front drum glide. In my case, one half was loose as the plastic plugs that pop into recesses to hold the glide in place had broken off. Remove the damaged glide section and replace it with the new section, popping the plastic plugs into the recesses. Don't be afraid to slap the glide to lock the plugs in place.
For the felt, I cut the part of the old felt that was pulling away from the front panel. I then used a flat-head screwdriver and wire brush to remove as much of the old adhesive as I could. Then, using the high-heat adhesive that came with the new felt, I put a generous amount on the front panel where the felt needed to go. I used a toothpick to spread the adhesive to get maximum area coverage. I let it set for a minute or two, and then placed the new felt. I used small clamps to keep the felt in place until the adhesive had time to bond. I only kept the clamps in place for 10 minutes.
Once I removed the clamps, I let the felt continue to adhere to the front panel for 24 hours before reassembling the dryer. Again, be careful of the wires connected to the front panel as it appears very easy for them to be pinched or cut when putting the front panel back in place.
When the dryer was reassembled, I plugged it back in and have had no more troubles. Read more...
PartSelect Number PS832645
Manufacturer Part Number 5303937183
The lower front felt seal with adhesive, also known as a drum felt seal, is used in dyers and allows the drum to easily glide on the front panel. For this repair project, you will need the following tools: #2 Phillips screw driver, #2 square head screw driver, putty knife, and wire bush. If your dryer will not tumble, or makes a squeaking noise when running, replacing this part could solve the problem. Remember to unplug your appliance from the power source for safety before you begin this installation project. Refer to the manual provided by the manufacturer for further installation instructions.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Timothy from Pensacola, FL
Felt pulling apart and glide not secured
For the glide, I want to advise people that to replace the entire glide you need to order two front drum glide parts as each is only half.First, unplug the dryer. Then, open the top so that you can get access to the work area. On each side of the inside front, there is a screw that connects the front panel to the side panels. Unscrew those screws and pull the front panel until it disconnects from the side panels. Be careful as there are wires that are secured to the bottom of the top inside lip of the front panel. One set of wires goes to the light bulb in the dryer door. You don't need to disconnect the wires, but be sure you don't damage the wires by pulling the front panel too far away from the dryer.
Once you have the front panel out of the way, you can see the front drum glide. In my case, one half was loose as the plastic plugs that pop into recesses to hold the glide in place had broken off. Remove the damaged glide section and replace it with the new section, popping the plastic plugs into the recesses. Don't be afraid to slap the glide to lock the plugs in place.
For the felt, I cut the part of the old felt that was pulling away from the front panel. I then used a flat-head screwdriver and wire brush to remove as much of the old adhesive as I could. Then, using the high-heat adhesive that came with the new felt, I put a generous amount on the front panel where the felt needed to go. I used a toothpick to spread the adhesive to get maximum area coverage. I let it set for a minute or two, and then placed the new felt. I used small clamps to keep the felt in place until the adhesive had time to bond. I only kept the clamps in place for 10 minutes.
Once I removed the clamps, I let the felt continue to adhere to the front panel for 24 hours before reassembling the dryer. Again, be careful of the wires connected to the front panel as it appears very easy for them to be pinched or cut when putting the front panel back in place.
When the dryer was reassembled, I plugged it back in and have had no more troubles. Read more...
Your Price
$9.62
In Stock
Kenmore Washer Dryer Combo Dryer Blower Housing Seal
PartSelect Number PS11743810
Manufacturer Part Number WP697770
This part seals between the blower housing and the blower housing cover.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Tammy from PINEVILLE, MO
Your Price
$9.62
In Stock
Kenmore Washer Dryer Combo Washer Inner Cap Seal
PartSelect Number PS11748108
Manufacturer Part Number WPW10072840
This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollable shaking and moving, loud noise, pumps but will not spin, or if your appliance will not agitate. This model is off-black in color and 3 inches in diameter. You will find this part inside the agitator in the middle of your washing machine. It is recommended to wipe down the barrier before putting the new seal on.
Fixes these symptoms
- Does not dispense fabric softener or detergent
- Leaking
- Marks left on clothes
- See more...
Installation Instructions
Lennis from Jacksonville, NC
Would not agita.
It was a blessing that I ordered the kit, because I thought it only needed the rubber seal and the four dogs. But because the seal and dogs cost less than the shipping I decided to order the kit and its good I did because the nochage on the basket sleeve was broke off. The blessing is that the sleeve was in the kit, sp it took 5 sec to slip it on along with the rest of the kit, and after about 15 min my wife was back to work. Thanks for saving me time and money without this web site I would have bought another brand new washer, thanks. Lennis from NC.
Read more...
Your Price
$17.28
In Stock
Kenmore Washer Dryer Combo Retainer O-ring
Remove 2 screws that held the top on the dryer.
Removed the 2 screw that held the front on the dryer.
Unhooked the belt from the tensioner and motor pulley.
Pulled the drum out. Removed the belt.
Removed the three screws that held the bearing assembly
on the back of the drum.
Removed the keeper o-ring slide the bad bearing off of shaft. Slide the new bearing on the shaft put the new o-ring on the shaft. Reassembled the bearing on back of the drum. Put belt back around the drum and put drum back in place. Put The belt around the motor pulley and tensioner
(this is probably the hardest part).
Put the front and top back together.
Turned the power back on. Job done Read more...
PartSelect Number PS266776
Manufacturer Part Number WE1M461
This authentic OEM rear bearing O-ring is designed for use with GE dryers. It helps secure the drum rear bearing onto the drum shaft, playing a key role in maintaining smooth and quiet dryer operation. A common sign that this part may need replacement is increased noise during the drying cycle. This O-ring is sold individually.
To replace the O-ring, you’ll need a Phillips screwdriver, a square-head screwdriver, a small flat-blade screwdriver, and needle-nose pliers. Always consult your dryer’s manual or parts diagram to ensure proper installation and compatibility.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Kerry from New Martinsville, WV
Noisy like a chain rattling inside
Disconnect Power from the DryerRemove 2 screws that held the top on the dryer.
Removed the 2 screw that held the front on the dryer.
Unhooked the belt from the tensioner and motor pulley.
Pulled the drum out. Removed the belt.
Removed the three screws that held the bearing assembly
on the back of the drum.
Removed the keeper o-ring slide the bad bearing off of shaft. Slide the new bearing on the shaft put the new o-ring on the shaft. Reassembled the bearing on back of the drum. Put belt back around the drum and put drum back in place. Put The belt around the motor pulley and tensioner
(this is probably the hardest part).
Put the front and top back together.
Turned the power back on. Job done Read more...
Your Price
$31.58
In Stock
Kenmore Washer Dryer Combo Front Upper Felt Seal With Adhesive
Replaced the slider felt on the drum and the belt since i had it apart. Also replaced the seal from the front panel to the blower motor.. while it was apart i cleaned the inside with bleach and a rag. reasembled a tryed it out. Run like a new dryer- Nice and quiet.- It had been sqeeking for months before the it stopped working. the time it took to fix it was a lot less hassle than it would have been to buy a new and get rid of the old one. And it saved me money. I love saving money!! I would recomend partsselec.com t.good prices,fast shipping, got what i needed. What more can you ask for.. Read more...
PartSelect Number PS832644
Manufacturer Part Number 5303937182
The upper felt seal for your dryer is attached to the top edge of the drum support area, and is held there by a high temperature adhesive. It creates a seal where the dryer door opens and closes, so that heat remains in the dryer while it tumbles. If your old upper felt seal is coming apart, you notice that hot air is leaking out the dryer door, or your clothes are taking too long to dry, you may need to replace the seal. When you order this part, it comes with the upper felt seal, as well as the required high-temperature adhesive.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Zaya from Weaverville, CA
Rear bearing assembly failed and damage heating element
Removed top using a butter knife to release the two tabs in the front(between the top and the front). Removed the front(two screws from the inside. removed rear louver panel(four screws). reached in through rear panel and released belt. removed drum assembly and change out, bearing assembly drum and bushing assembly in the back panel, being sure not to forget the grounding bearing(had my 9 year old give me an extra hand to hold the ball bearing on the back..Replaced the slider felt on the drum and the belt since i had it apart. Also replaced the seal from the front panel to the blower motor.. while it was apart i cleaned the inside with bleach and a rag. reasembled a tryed it out. Run like a new dryer- Nice and quiet.- It had been sqeeking for months before the it stopped working. the time it took to fix it was a lot less hassle than it would have been to buy a new and get rid of the old one. And it saved me money. I love saving money!! I would recomend partsselec.com t.good prices,fast shipping, got what i needed. What more can you ask for.. Read more...
Related Kenmore Washer Dryer Combo Parts
- All Kenmore Washer Dryer Combo parts
- Kenmore Washer Dryer Combo Agitators
- Kenmore Washer Dryer Combo Bearings
- Kenmore Washer Dryer Combo Belts
- Kenmore Washer Dryer Combo Brackets and Flanges
- Kenmore Washer Dryer Combo Caps and Lids
- Kenmore Washer Dryer Combo Circuit Boards and Touch Pads
- Kenmore Washer Dryer Combo Dispensers
- Kenmore Washer Dryer Combo Doors
- Kenmore Washer Dryer Combo Drums and Tubs
- Kenmore Washer Dryer Combo Ducts and Vents
- Kenmore Washer Dryer Combo Elements and Burners
- Kenmore Washer Dryer Combo Filters
- Kenmore Washer Dryer Combo Fuses
- Kenmore Washer Dryer Combo Handles
- Kenmore Washer Dryer Combo Hardware
- Kenmore Washer Dryer Combo Hinges
- Kenmore Washer Dryer Combo Hoses and Tubes
- Kenmore Washer Dryer Combo Knobs
- Kenmore Washer Dryer Combo Latches
- Kenmore Washer Dryer Combo Legs and Feet
- Kenmore Washer Dryer Combo Lights and Bulbs
- Kenmore Washer Dryer Combo Motors
- Kenmore Washer Dryer Combo Panels
- Kenmore Washer Dryer Combo Pulleys
- Kenmore Washer Dryer Combo Sensors
- Kenmore Washer Dryer Combo Springs and Shock Absorbers
- Kenmore Washer Dryer Combo Switches
- Kenmore Washer Dryer Combo Thermostats
- Kenmore Washer Dryer Combo Timers
- Kenmore Washer Dryer Combo Transmissions and Clutches
- Kenmore Washer Dryer Combo Valves
- Kenmore Washer Dryer Combo Wheels and Rollers
- Kenmore Washer Dryer Combo Wire Plugs and Connectors