Hotpoint Washer Springs and Shock Absorbers
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Hotpoint Washer Springs and Shock Absorbers
Your Price
$33.90
In Stock
Hotpoint Washer Dampening Strap
PartSelect Number PS271100
Manufacturer Part Number WH1X2727
The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash cycle, the washing machine tub could be off-balance, meaning one or more of these straps may be loose, or broken. Other symptoms include: the washer leaking, not agitating, or pumping but not spinning. These straps are sold individually. However, we recommend that you replace all 4 straps at the same time. It is also recommended that you check the tub for cracks where these straps mount.
Fixes these symptoms
- Burning smell
- Leaking
- Noisy
- See more...
Installation Instructions
molly from laguna niguel, CA
broken dampening strap and loose agitator
first remove the front washer cover by finding the two pressure clips that hold it to the top lid. gently push the putty knife into the clips one at a time. this will raise and separate them from the front panel. the panel will tilt forward and u can now remove it from the bottom clips by sliding it up and out. to open the top cover u remove the two 1/4 in screws on the sides of the front panel and lift the top. make sure to secure it in place or unplug the single electrical connection at the rear and remove the whole top from the clips, its really simple and the most convenient mehtod. to remove the straps u can now get to all four without much interference. there are two size screw heads so make sure u have a nut driver or small socket set. after changing the straps i went to change the agitator coupling. the agitator pulled directly up without a problem. just put your two hands under and pull straight up with one good jolt. the plastic coupler has one bolt in the middle that came out easily with a small socket set. my problem arose when the plastic coupler would not come off the metal shaft. after a short time of pulling and prying i finally decided to cut it off. using a small hacksaw and taking my time i put two cuts into the coupler. they were on opposite sides and where vertical, running along the steel shaft. i could now split it in two and it came off very easily and quickly. now when putting on the new one make sure the splines line up. push as far down as u can then use the center bolt to seat the gear all the way down. the agitator also has to be lined up just right. it also has splines on the interior that allow it to line up with the coupler and merely push down until it reseats itself in place. replace the top of the washer and then the front panel. don't forget to rebolt the top panel to the frame. push the front panel in until it snaps into place. full replacement time was about 40 minutes and actually not bad with the right tools.
Read more...
Hotpoint Washer Spring Clutch
PartSelect Number PS11763251
Manufacturer Part Number WH01X24434
Fixes these symptoms
- Noisy and Marks Left on Clothes
- Spinning Issues
- Will not agitate
- See more...
Installation Instructions
Selinda from BELLE GLADE, FL
Grinding noise when washing
I watch a YouTube video with the same problem and follow each step
Read more...
Hotpoint Washer Rod & Spring Assembly Right - Red
PartSelect Number PS12343378
Manufacturer Part Number WH16X26908
Fixes these symptoms
- Shaking and Moving
- Spinning Issues
- See more...
Installation Instructions
chris from SHELBY, AL
Machine was noisy and banging during spin cycle
Watched the part select instructional video on YouTube. Repair was very easy. Appliance repair man quoted me $335 for this repair. I did it myself for a fraction of the cost.
Read more...
Hotpoint Washer Front Suspension Rod & Spring Assembly Blue
PartSelect Number PS3654190
Manufacturer Part Number WH16X10158
Sold individually. This part is used to keep your tub upright and somewhat level during the different cycles.
Your Price
$79.63
In Stock
Hotpoint Washer Red Rear Suspension Rod & Spring Assembly
PartSelect Number PS3654191
Manufacturer Part Number WH16X10159
Your Price
$13.95
In Stock
Hotpoint Washer Socket Rod Support - White
The parts arrived 3 days later. Installed the parts and the washing machine was working within a half hour. Read more...
PartSelect Number PS268394
Manufacturer Part Number WH01X10001
This part is a replacement socket rod support for your washer. The socket rod support is found at the top of the washer frame in the front part of the washer. It supports the suspension rod, so the rod can prevent the tub from shaking too much during operation. If your washer is shaking excessively or emitting an odd sound during use, it may be because the rod support is broken, and the suspension rod is not able to do its job. This part is made of white plastic and is sold individually.
Installation Instructions
Roman from Amherst, MA
Wasing machine strted to make horrible
took it appart and found that the suspension rod was broken. went on line an ordered the parts.The parts arrived 3 days later. Installed the parts and the washing machine was working within a half hour. Read more...
Your Price
$39.55
In Stock
Hotpoint Washer Rod And Spring Assembly - Green
PartSelect Number PS960673
Manufacturer Part Number WH16X10057
This part helps center and support the drum, transmission and motor assembly.
Hotpoint Washer Rod & Spring Assembly
PartSelect Number PS270406
Manufacturer Part Number WH16X10011