General Electric Washer Dryer Combo Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular General Electric Washer Dryer Combo Parts
Your Price
$17.15
In Stock
General Electric Washer Dryer Combo Dryer Bearing Slide (2 Pack)
Reviewed YouTube videos.
Patience is required, take your time, take photos of the wires and also make a written wiring chart. This was the flaw in my planning. Reference the schematics from PartsSelect to number the controls. Do NOT use masking tape to identify the wires as they will have all stuck together by the time you go to reinstall them.
Most difficult process was removing and identifying the numerous wires to the back panel. They have push connectors, but some were very difficult to remove. The people doing the "how to" videos no doubt had them partially released and that made it look easy. Examine the connectors before removing to identify how they are captured by the connector. A paper clip "tool" I made enabled me to release some of the capture lugs, but some were so tight, I had to use small needle-nose pliers to open up the lug to release the wire on the connector.
When reinstalling, re-tighten those connectors.
Replacing the parts was much easier than the wiring disconnect/reconnect process. I'm happy to report that replacing the rear bearing and the front 2 green and 2 white shim/bearings immediately and completely solved my problem. For about $150, I restored my dryer to "like-new" functionality and got a lot of satisfaction from doing it. The project took about 4 hours, which could have been reduced to 2 hours had I know about the clip release and wiring identification process. Also, make sure you thoroughly vacuum out your unit while it is disassembled. Good luck!!! Read more...
PartSelect Number PS17137207
Manufacturer Part Number WE03X37319
This drum glide bearing is an authentic OEM replacement part that is compatible with dryers. It is white in color and made of highly durable plastic. The bearing allows the drum to rotate smoothly and dry your clothes thoroughly and evenly. It keeps the drum stable and protects it from excessive friction damage. Over time, the bearing may wear down or break due to normal aging or wear from repeated use. If the bearing is no longer able to support the drum, you will likely notice unusually loud grinding or squeaking noises from the dryer. You may also notice increased drying times due to poor drum rotation. Inspect all the bearings on your dryer, as they tend to wear down at the same time. Each drum glide bearing is sold individually.
Fixes these symptoms
- Drum Not Spinning
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
mike from SUMMERVILLE, SC
Dryer was making increasingly loud "thumping" sound.
Parts were shipped quickly, packaged correctly, and were in original GM packages - very reassuring. BTW, your customer service is excellent.Reviewed YouTube videos.
Patience is required, take your time, take photos of the wires and also make a written wiring chart. This was the flaw in my planning. Reference the schematics from PartsSelect to number the controls. Do NOT use masking tape to identify the wires as they will have all stuck together by the time you go to reinstall them.
Most difficult process was removing and identifying the numerous wires to the back panel. They have push connectors, but some were very difficult to remove. The people doing the "how to" videos no doubt had them partially released and that made it look easy. Examine the connectors before removing to identify how they are captured by the connector. A paper clip "tool" I made enabled me to release some of the capture lugs, but some were so tight, I had to use small needle-nose pliers to open up the lug to release the wire on the connector.
When reinstalling, re-tighten those connectors.
Replacing the parts was much easier than the wiring disconnect/reconnect process. I'm happy to report that replacing the rear bearing and the front 2 green and 2 white shim/bearings immediately and completely solved my problem. For about $150, I restored my dryer to "like-new" functionality and got a lot of satisfaction from doing it. The project took about 4 hours, which could have been reduced to 2 hours had I know about the clip release and wiring identification process. Also, make sure you thoroughly vacuum out your unit while it is disassembled. Good luck!!! Read more...
Your Price
$21.45
In Stock
General Electric Washer Dryer Combo Direct Drive Motor Coupling
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...
PartSelect Number PS1485646
Manufacturer Part Number 285753A
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft. It attaches to the direct-drive transmission and the motor shaft. If this part is defective it will affect the agitator in your washer because of its direct connection with the motor. Your washer may not agitate, spin slowly, or not spin at all. The coupling must be replaced when there is no longer a consistent connection between the transmission and the motor shaft. The coupling can wear over time because of its location between two major parts of the dryer. It is subject to material fatigue over time from normal use, or breakage caused by frequent overloading. The part measures approximately 2 inches in diameter, and is constructed of plastic and metal. This model comes in black/white.
Fixes these symptoms
- Burning smell
- Draining Issues
- Leaking
- See more...
Installation Instructions
Jeff from Wayne, NJ
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...
Your Price
$25.75
In Stock
General Electric Washer Dryer Combo Dryer Bearing Slide (2 Pack)
Reviewed YouTube videos.
Patience is required, take your time, take photos of the wires and also make a written wiring chart. This was the flaw in my planning. Reference the schematics from PartsSelect to number the controls. Do NOT use masking tape to identify the wires as they will have all stuck together by the time you go to reinstall them.
Most difficult process was removing and identifying the numerous wires to the back panel. They have push connectors, but some were very difficult to remove. The people doing the "how to" videos no doubt had them partially released and that made it look easy. Examine the connectors before removing to identify how they are captured by the connector. A paper clip "tool" I made enabled me to release some of the capture lugs, but some were so tight, I had to use small needle-nose pliers to open up the lug to release the wire on the connector.
When reinstalling, re-tighten those connectors.
Replacing the parts was much easier than the wiring disconnect/reconnect process. I'm happy to report that replacing the rear bearing and the front 2 green and 2 white shim/bearings immediately and completely solved my problem. For about $150, I restored my dryer to "like-new" functionality and got a lot of satisfaction from doing it. The project took about 4 hours, which could have been reduced to 2 hours had I know about the clip release and wiring identification process. Also, make sure you thoroughly vacuum out your unit while it is disassembled. Good luck!!! Read more...
PartSelect Number PS17626249
Manufacturer Part Number WE03X37320
This OEM replacement dryer slide bearing is white in color, and approximately 3 inches long. The slide bearings are supportive linings for your dryer. If they have eroded, or are damaged, the drums will scrape against metal during the drying cycle which will produce a squealing, or scraping sound.
Fixes these symptoms
- Drum Not Spinning
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
mike from SUMMERVILLE, SC
Dryer was making increasingly loud "thumping" sound.
Parts were shipped quickly, packaged correctly, and were in original GM packages - very reassuring. BTW, your customer service is excellent.Reviewed YouTube videos.
Patience is required, take your time, take photos of the wires and also make a written wiring chart. This was the flaw in my planning. Reference the schematics from PartsSelect to number the controls. Do NOT use masking tape to identify the wires as they will have all stuck together by the time you go to reinstall them.
Most difficult process was removing and identifying the numerous wires to the back panel. They have push connectors, but some were very difficult to remove. The people doing the "how to" videos no doubt had them partially released and that made it look easy. Examine the connectors before removing to identify how they are captured by the connector. A paper clip "tool" I made enabled me to release some of the capture lugs, but some were so tight, I had to use small needle-nose pliers to open up the lug to release the wire on the connector.
When reinstalling, re-tighten those connectors.
Replacing the parts was much easier than the wiring disconnect/reconnect process. I'm happy to report that replacing the rear bearing and the front 2 green and 2 white shim/bearings immediately and completely solved my problem. For about $150, I restored my dryer to "like-new" functionality and got a lot of satisfaction from doing it. The project took about 4 hours, which could have been reduced to 2 hours had I know about the clip release and wiring identification process. Also, make sure you thoroughly vacuum out your unit while it is disassembled. Good luck!!! Read more...
Your Price
$73.04
In Stock
General Electric Washer Dryer Combo Door Handle
PartSelect Number PS12743305
Manufacturer Part Number WE01X30378
This is a door handle made for use with dryers. This door handle is made of solid white plastic and allows you to open and close the door of the dryer. If your current dryer door handle is broken or missing, it will need to be replaced. This handle measures 9 inches long and 2 inches thick and attaches at its top and base. To replace this handle, simply pry off its left side and pull it off, and then insert the prongs on the right side into the door and push it in place. This OEM door handle is sold on its own and does not come with any other accessories.
Fixes these symptoms
- Door won’t close
- See more...
Installation Instructions
William from Carol Stream, IL
Plastic handle on dryer snapped off.
Replacement handle easily snapped into dryer door. No skill or tool needed,.
Read more...
Your Price
$34.96
In Stock
General Electric Washer Dryer Combo Push-to-start Switch
PartSelect Number PS3487190
Manufacturer Part Number WE4M416
Restore reliable operation to your GE dryer with this genuine OEM push-to-start switch, designed specifically for use with a range of GE dryer models. This switch activates the dryer when you press and release the button, making it an essential component for proper startup.
Common signs that this part may need replacement include the dryer failing to start or starting unexpectedly without pressing the switch. Replacing the switch is a straightforward repair and requires only a Phillips screwdriver and a flathead screwdriver. Before beginning the installation, always disconnect the power to ensure safety. Once the power is off, remove the control panel screws, disconnect the old switch, and install the new one in its place.
This part is sold individually and is a reliable solution for restoring your dryer's functionality with minimal effort.
Fixes these symptoms
- Timer Not Working
- Touchpad does not respond
- Will Not Start
- See more...
Installation Instructions
Gary from LAVALLETTE, NJ
replaced start button and start switch
disconnect power plug unscrew 3 screws in back. lean forward remove button disconnect 2 wires in back of switch. put switch connect 2 wires and button. connect 3 screws in the back. ready to start working
Read more...
Your Price
$64.43
In Stock
General Electric Washer Dryer Combo Grid Asm
PartSelect Number PS16762559
Manufacturer Part Number WE22X35337
This is a replacement lint filter slide for your dryer. It is approximately 14 inches long and 5 inches wide. It is made of white plastic and is sold individually. The slide mounts to your dryer and allows the lint filter to slide out for cleaning. If your lint filter will not slide out properly, you may need to replace the slide. This part is an authentic OEM part sourced directly from the manufacturer.
Installation Instructions
Joel from LAKE WORTH, FL
Probably due to age and heat of the dryer,the top of the slide broke.
I removed the old slide and clipped in the new one. No tools involved.
Read more...
Your Price
$30.39
In Stock
General Electric Washer Dryer Combo Sponge
PartSelect Number PS17139170
Manufacturer Part Number WH01X35719
Keep your washer-dryer combo running smoothly with this reusable foam lint filter. It traps more lint to improve airflow, prevent clogs, and help your appliance dry clothes efficiently. Washable and built to last, this filter is an easy, eco-friendly alternative to single-use options. If your old filter is worn or clogged, swapping it out is quick and simple—just remove the old one and slide the new filter into place.
Installation Instructions
Marian from Perrysburg, OH
Your Price
$86.43
In Stock
General Electric Washer Dryer Combo Drain Pump & Filter
PartSelect Number PS18351790
Manufacturer Part Number WH11X39237
This drain pump and filter assembly is a genuine OEM replacement assembly that is designed for washing machines. It is responsible for removing water from the washing machine tub at the end of each wash cycle and trapping any debris or foreign objects like lint, hair, and coins that may clog the drainage system. Signs of a fault in the drain pump and filter assembly include the washer not draining properly, leaving water in the drum at the end of the cycle; unusual noises during the drain cycle, such as grinding or humming sounds; and visible leaks or drips around the pump or filter area.
Fixes these symptoms
- Draining Issues
- Leaking
- Will not drain
- See more...
Installation Instructions
Cheston O from Clayton, NC
Pump Replacement
The first thing to get is a baking sheet/pan and a bucket. You'll want to get it as close to the drain as possible. Be ready for ALOT of water to be in there. Ease it out and dump the water into the bucket until it's all out. Next you'll have to prop up the front of the machine at least 4 or 5 inches. You'll need pliers to loosen the hose clamp. There's only 4 screws so it's pretty easy, but you'll only be able to see the 2 in front. The other 2 you'll have to feel your way thru it.
Read more...
Your Price
$81.32
In Stock
General Electric Washer Dryer Combo Lid Lock & Switch Assembly
PartSelect Number PS3496878
Manufacturer Part Number WH44X10288
The door latch lid lock is to lock the door on your washer when the appliance is in use. Your washer will not start if your door is not locked. If your latch is broken, you may not be able to start a cycle or open your washer door. It is mostly black in color and made of plastic. This part measures approximately 3.75 by 3.5 inches.
Fixes these symptoms
- Lid or door won’t close
- Locking Issues
- Will not drain
- See more...
Installation Instructions
Randy from CANTON, NC
Washer would not spin or drain
I went to You tube sight to see how I can remove front of washer so I could inspect inside and see if the problem was visible. A butter knife easily released the tabs that hold the front of washer on. My wife in the mean time found a you tube video that showed the same problem and I ordered the part right away. It showed just two screws and a plug that had to be removed. I always buy my parts from part-select because the quality and speedy delivery and tracking is great! This was an easy fix!
Read more...
Your Price
$62.51
In Stock
General Electric Washer Dryer Combo Door Lock
PartSelect Number PS12749276
Manufacturer Part Number WH01X29528
This genuine OEM door lock is a replacement part specially designed for front-load washing machines. It is a safety mechanism designed to prevent the door from being opened during the wash cycle. When the door is closed, the lock engages automatically, securing the door shut until the cycle is complete and it is safe to open. This ensures that water and detergent do not spill out of the washer and cause injury. Over time, the door lock may fail due to physical damage or normal wear and tear. If the door lock is faulty, you may encounter issues such as the door not locking properly, leading to the washer not starting or stopping mid-cycle. You may also notice excessive noise and shaking while the washer is running.
Fixes these symptoms
- Lid or door won’t close
- Locking Issues
- Will Not Start
- See more...
General Electric Washer Dryer Combo Appliance Types
Related General Electric Washer Dryer Combo Parts
- General Electric Washer Dryer Combo Bearings
- General Electric Washer Dryer Combo Knobs
- General Electric Washer Dryer Combo Seals and Gaskets
- General Electric Washer Dryer Combo Latchs
- General Electric Washer Dryer Combo Motors
- General Electric Washer Dryer Combo Switches
- General Electric Washer Dryer Combo Hardware
- General Electric Washer Dryer Combo Springs and Shock Absorbers
- General Electric Washer Dryer Combo Thermostats
- General Electric Washer Dryer Combo Brackets and Flanges
- General Electric Washer Dryer Combo Circuit Boards and Touch Pads
- General Electric Washer Dryer Combo Valves
- General Electric Washer Dryer Combo Drums and Tubs
- General Electric Washer Dryer Combo Sensors
- General Electric Washer Dryer Combo Pulleys
- General Electric Washer Dryer Combo Hoses and Tubes
- General Electric Washer Dryer Combo Dispensers
- General Electric Washer Dryer Combo Caps and Lids
- General Electric Washer Dryer Combo Wire Plugs and Connectors
- General Electric Washer Dryer Combo Panels
- General Electric Washer Dryer Combo Elements and Burners
- General Electric Washer Dryer Combo Hinges
- General Electric Washer Dryer Combo Fuses
Popular General Electric Washer Dryer Combo Models
Below are the most popular General Electric Washer Dryer Combo models we have. Enter your model number in the search box to find your model.
- GUD27ESSM1WW
- GUD24ESSM1WW
- GUD27ESSJ0WW LAUNDRY CENTER
- WSM2700DAWWW
- GUD27ESSJ1WW LAUNDRY CENTER
- GTUP270EM1WW
- GUD24ESSJ0WW HOME LAUNDRY COMBO
- GUD27ESPM1DG
- GTUP270EM4WW
- GTUP240EM1WW
- GUD27GSSM2WW
- WSM2420D3WW
- WSM2700HBWWW
- GTUN275EM1WW
- GTUP270EM0WW
- GTUP240EM5WW
- PFQ97HSPV0DS
- GUD24GSSM1WW
- GUD27ESSM0WW
- GTUP270EM5WW HOME LAUNDRY COMBO