This drain pump and filter assembly is a genuine OEM replacement assembly that is designed for washing machines. It is responsible for removing water from the washing machine tub at the end of each wash cycle and trapping any debris or foreign objects like lint, hair, and coins that may clog the drainage system. Signs of a fault in the dr...Read moreain pump and filter assembly include the washer not draining properly, leaving water in the drum at the end of the cycle; unusual noises during the drain cycle, such as grinding or humming sounds; and visible leaks or drips around the pump or filter area.
This genuine OEM door lock is a replacement part specially designed for front-load washing machines. It is a safety mechanism designed to prevent the door from being opened during the wash cycle. When the door is closed, the lock engages automatically, securing the door shut until the cycle is complete and it is safe to open. This ensures...Read more that water and detergent do not spill out of the washer and cause injury. Over time, the door lock may fail due to physical damage or normal wear and tear. If the door lock is faulty, you may encounter issues such as the door not locking properly, leading to the washer not starting or stopping mid-cycle. You may also notice excessive noise and shaking while the washer is running.
This long shipping bolt is a heavy-duty fastener designed to secure the washer’s tub to the frame during transport, preventing internal damage caused by vibrations. It is essential for safe shipping and installation but must be removed before operating the appliance to avoid serious malfunction. Commonly used in front-loading washing mach...Read moreines, this steel bolt ensures the drum remains stable during transit. Always verify compatibility with your specific model and follow safety guidelines when installing or removing this part.
Keep your washer running smoothly with this genuine door latch. It helps keep the door securely closed during cycles, preventing leaks and making sure everything works as it should. Made for select GE, Hotpoint, Haier, Monogram, and Café models—just check your model before ordering.
This shipping bolt secures internal components during transport to prevent movement or damage. Proper use helps maintain alignment and protection. Replacing a missing bolt restores safe handling and transport readiness.
This leveling leg is designed to stabilize the appliance by allowing precise height adjustment on uneven floors. Proper leveling helps reduce vibration, noise, and door alignment issues, making this an essential replacement when the original leg is bent, broken, or missing.
This suspension damper helps stabilize the appliance by absorbing movement and vibration during operation. It supports smooth performance and helps reduce noise or excessive motion. Replacing a worn damper restores proper balance and protects internal components from strain.
This clamp secures the boot gasket in place, ensuring a tight seal between connected components. Proper fastening helps prevent leaks and maintains alignment during operation. Replacing a loose or damaged clamp restores secure sealing and reliable performance.
This hose is a replacement fluid-transfer component designed to move water from the tub to the pump. It is commonly replaced to resolve leaks, drainage issues, or blockages and helps restore proper water flow.
This lint filter handle is a genuine replacement part for GE washer/dryer combos, designed to provide easy access to the lint filter for cleaning. Proper maintenance of the lint filter ensures efficient airflow and optimal drying performance. This handle restores functionality when the original is damaged or missing and installs quickly for a secure fit.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sherrie Groff - For model number PFQ97HSPV0DS
October 1, 2025
I need to replace the foam side of my filter, can you purchase a foam filter or do you have to buy the whole filter? I am also looking for something to fit inside to clean the lint out of the opening where the filter fits. Any ideas would help
Hi Sherrie, thank you for reaching out. Yes, you can purchase the foam filter for your model. Its part number is PS17139170. We hope that helps!
Hi Robert, thank you for reaching out. Pull out the lint screen. Remove the visible lint with your fingers and dispose of it. For a deeper clean of the screen itself, wash it with warm, soapy water and a nylon brush to remove residue from fabric softeners or detergents, then let it air dry completely before reinserting. Use a long, flexible dryer vent brush to reach deep into the empty lint filter compartment. Move the brush around to loosen any lint and dust stuck to the sides and bottom of the slot. We hope this information helps!
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Bruce - For model number PFQ97HSPV0DS
November 2, 2025
looking for lint filter holder that pulls out from machine.
Hello Bruce, thank you for getting in touch. According to our research, the part you are looking for is part number PS17833661. We hope this helps.
I am just needing the seal/gasket on the drain pump filter because mine is torn. Is it possible to buy just that gasket?
Hi Amanda, thank you for getting in touch. The drain pump and filter, part number PS18351790, for your model comes in an assembly. The gasket is not listed separately. We hope this information helps!
We are having issues with drying times. I understand that it's ventless and that that will effect time, but we are running into drying times of 2+hours with just a regular load of non heavy items. What can I check besides making sure the filter is clean?
Hello Greg, thank you for the question. Start by cleaning the lower drain pump filter behind the small access panel at the bottom front of the machine. If this filter is clogged with lint and debris, water cannot drain properly during the dry cycle, leaving your clothes in a humid environment that significantly extends drying time. Next clean the secondary foam filter thoroughly with soap and water, fabric softener residue can saturate this filter and severely restrict airflow even when it looks clean at a glance. Also, inspect the internal heat pump fins inside the lint housing. The primary filter does not catch all lint and over time buildup on these fins blocks airflow significantly. Use a long flexible brush or vacuum crevice tool to gently clear any lint from the fins. Finally check the external drain hose behind the machine. If it is kinked, blocked, or inserted too far into the standpipe the pump cannot clear water efficiently, forcing moisture back into the drum and extending the dry cycle. We hope this is what you were looking for!
Was this helpful?
Thank you for voting!
Prev
1
2
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No spin, no drain
7 of 15 peoplefound this instruction helpful.
Peter from CLAYTON, NC
Easy
30 - 60 mins
Nutdriver, Pliers
Disassemble according to instructions then remove pump...my only issue was I ordered the pump and paid $11.95 for t 2 to 3 days shipping. I didn't get the part until the following Saturday which was like 6 to 7 days...horrible delivery
Was this helpful?
Thank you for voting!
Pump Replacement
4 of 6 peoplefound this instruction helpful.
Cheston O from Clayton, NC
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
The first thing to get is a baking sheet/pan and a bucket. You'll want to get it as close to the drain as possible. Be ready for ALOT of water to be in there. Ease it out and dump the water into the bucket until it's all out. Next you'll have to prop up the front of the machine at least 4 or 5 inches. You'll need pliers to loosen the hos
... Read moree clamp. There's only 4 screws so it's pretty easy, but you'll only be able to see the 2 in front. The other 2 you'll have to feel your way thru it.
Read less
Was this helpful?
Thank you for voting!
Washer running but not draining
4 of 6 peoplefound this instruction helpful.
Peter from Seattle, WA
Easy
1- 2 hours
Pliers, Screw drivers
Followed YouTube instructions to lay the machine on its back, for easier access to the pipes and drain pump from the exposed bottom of the machine. Cleared the pipes first of a slight clog in the filter, turned the machine upright again, but it still did not drain. Laid the machine on its back again, after ordering a new drain pump, and f
... Read moreitted the new pump. Again, it did not work, but left the new pump in and ordered a new control board. Fitting a new control board involves detaching the control panel and cabinet top, which is not hard, then extracting the old control board. Taking off the wiring clips turned out to be significantly more difficult than re-connecting them when the new control board arrived. Fitting a new control board can easily be done with the machine upright. This time the draining did work, yay, and the washer is now fully functional again.
My Orders
