Craftsman Trimmer Carburetors

Craftsman Trimmer Carburetor

★★★★★

★★★★★

4 Reviews

A carburetor basically consists of an open pipe through which the air passes into the inlet manifold of the engine. The pipe is in the form of a Venturi: it narrows in section and then widens again, causing the airflow to increase in speed in the narrowest part. Below the Venturi is a butterfly valve called the throttle valve ' a rotating disc that can be turned end-on to the airflow, so as to hardly restrict the flow at all, or can be rotated so that it (almost) completely blocks the flow of air. This valve controls the flow of air through the carburetor throat and thus the quantity of air/fuel mixture the system will deliver, thereby regulating engine power and speed. The throttle is connected, usually through a cable or a mechanical linkage of rods and joints. Fuel is introduced into the air stream through small holes at the narrowest part of the Venturi and at other places where pressure will be lowered when not running on full throttle.

Craftsman Trimmer Purge Bulb

Craftsman Trimmer Carburetor Kit

★★★★★

★★★★★

1 Review

This carburetor mixes air and fuel to power small engines, helping ensure smooth starting and reliable performance. Built from durable materials, it supports consistent fuel delivery and efficient operation. Replacing a worn or faulty carburetor can resolve issues such as hard starting, rough idling, or poor acceleration, restoring proper engine function.

Craftsman Trimmer Carburetor

★★★★★

★★★★★

1 Review

This carburetor is supplied by the original manufacturer as a replacement part for gas trimmers. It is made up of a metal body and plastic choke lever. The carburetor is responsible for mixing air and fuel for combustion within the engine. Over time, it can fail due to various reasons such as blockage in the fuel connections, clogged jets, damaged float, a worn-out needle valve, or a faulty gasket. A faulty carburetor will result in poor idling, difficulty starting, loss of power, stalling, and misfires. Before beginning any repairs on the carburetor, drain the fuel from the fuel tank and disconnect the fuel lines. Remove the air filter assembly and disconnect all other attachments that secure the carburetor to the engine. Remove the mounting fasteners that hold the carburetor and carefully pull it off the engine. Inspect the carburetor gasket and replace it as well if it is no longer providing an adequate seal. Place the new carburetor in position and reinstall the mounting fasteners to keep it in place. Reassemble the equipment in reverse order to complete the repair.

Craftsman Trimmer Walbro Gasket/diaphragm Kit

★★★★★

★★★★★

1 Review

This is an authentic OEM replacement kit for use with lawn and garden equipment. Each kit includes the carburetor, cylinder, crankcase, and muffler gaskets. The carburetor gasket seals the area between the carburetor and engine block to prevent the entry of contaminants into the carburetor. The crankcase gasket prevents oil from leaking out of the crankcase. The cylinder and muffler gaskets prevent the combustion and exhaust gases from escaping. If you are experiencing common problems such as leaking, loss of compression, and poor engine performance this indicates that your gaskets may be worn down or damaged and need replacement. Carefully remove the old gaskets and thoroughly clean the mating surfaces where the new gaskets will be installed to ensure a good seal. Install the new gaskets and ensure that they fit properly.

Craftsman Trimmer Adjustment Boot Carburetor This genuine OEM carburetor intake boot adapter is a rubber replacement part used in trimmers to connect the carburetor to the carburetor adapter. It ensures a proper seal and allows the air-fuel mixture to flow into the combustion chamber. Over time, the boot adapter may wear out, warp, or develop cracks. Signs of a broken boot adapter include air or fuel leaks around the carburetor and engine issues like rough idling, stalling, or misfires. Using a damaged boot adapter can lead to reduced power and premature wear. To replace the boot adapter, you will need a screwdriver, pliers, a wrench, and a nut driver. Consult your user manual for guidance on accessing the carburetor through the airbox housing. Remove the air filter and airbox base, then locate and remove the faulty air intake boot from the carburetor. Please keep in mind that this boot adapter is not included with the carburetor kit or the carburetor adapter

Craftsman Trimmer Carburetor Ac3.1 A carburetor is an important component which combines fuel and air before the combustible mixture is sent into the cylinder. Over time parts may wear out or get damaged eventually requiring a replacement. Keep in mind this high-quality carburetor is sold as an individual item. Refer to the appropriate diagrams for your model to ensure the correct repair procedure. It is a genuine OEM carburetor which is specially made for lawn and garden equipment.

Craftsman Trimmer Carburetor This is a genuine OEM replacement part, it is sold individually. It is used on specific Gas Trimmers. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem.

Craftsman Trimmer Carburetor This is an original replacement part sourced directly from the manufacturer. The carburetor is found in Craftsman trimmers. This part is a complete carburetor assembly made primarily of metal, and is used to mix fuel and air together for ignition in the engine. You will require a screwdriver when replacing this item. The carburetor is sold as an individual replacement part.

Craftsman Trimmer Carburetor This is an authentic part that is supplied directly from the original equipment manufacturer for Craftsman trimmers. The carburetor mixes air and gas before the fuel mix goes to the engine. This part comes with the carburetor assembly, as well as the carburetor gasket. Let the engine cool and drain the gas tank before starting this repair. You may need screw drivers and pliers to aid you in this repair.