Black and Decker Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Black and Decker Parts
Your Price
$6.40
In Stock
Black and Decker Cover Spool
PartSelect Number PS18981315
Manufacturer Part Number 385022-03N
This cover is designed for use with trimmers and edgers and is a genuine OEM part. Made of plastic, this cover is used to hold and secure the spool or line within the trimmer cutter head assembly. If the cover for your trimmer is broken or damaged and cannot contain the spool or line, the cover needs to be replaced immediately. To replace the cover, push in the upper slots on the cover, which will disconnect and release it from the rest of the assembly.
Your Price
$13.68
In Stock
Black and Decker Brush And Spring
PartSelect Number PS10166057
Manufacturer Part Number 145323-06
This Genuine OEM carbon brush is an essential replacement part designed for use with a variety of DeWALT and Black & Decker saws. Sold individually, this high-quality component is made to conduct electrical current within the motor, enabling efficient power transfer and tool performance. Over time, carbon brushes naturally wear down due to friction and electrical contact, which can lead to intermittent motor issues or failure to start.
Measuring 3/4 inch in length, 1/2 inch in width, and 1/4 inch in thickness, this brush is built to original specifications for a precise fit. When replacing carbon brushes, it’s important to also inspect the motor’s armature for signs of burns, cracks, or other damage, which may indicate a more serious issue. A hex key or screwdriver may be required for installation, depending on your tool model.
Fixes these symptoms
- Won't turn on
- See more...
Your Price
$27.10
In Stock
Black and Decker Power Cord
PartSelect Number PS10169875
Manufacturer Part Number 330072-98
Length: 8'
Gauge: 18
Wires: 2
Type: Bare Wire
This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also routing the cord and wires in the right path can help avoid pinching when the tool case (Plate) is put back into place.
Your Price
$7.60
In Stock
Black and Decker Carbon Brush
PartSelect Number PS12517203
Manufacturer Part Number N031634
Genuine Porter Cable replacement part Includes 1 Carbon Brush with wire lead attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. • Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. • A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. • When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.
Your Price
$39.16
In Stock
Black and Decker Pad
PartSelect Number PS12398026
Manufacturer Part Number 151281-08
The 151281-08 Pad is used to hold 5 inch Hook and Loop sandpaper with 8 vacuum holes.
Over the past few years the popularity of Hook and Loop paper has grown because of the ease of changing sandpaper when needed. Over that of the PSA (Pressure Sensitive Sandpaper)
Applying too much pressure on the sander may cause premature wear on the Hook and Loop pad.
When a pad needs to be replaced, simply remove the three screws that hold the pad to the sander, then replace it with a new pad.
Your Price
$7.06
In Stock
Black and Decker Blade Adapter Ring
PartSelect Number PS10166690
Manufacturer Part Number 152636-00
This is a genuine Dewalt replacement part, it is sold individually. The purpose of the Blade Adapter, is to make the bore of a blade that is 1 inch and reduce to a 5/8 inch bore. Making it possible to use a 1 inch bore blade on a 5/8 inch arbor.
Your Price
$7.78
In Stock
Black and Decker Drain Valve
PartSelect Number PS12508562
Manufacturer Part Number N286039
Frequently referred to as a Drain Plug, this Drain Valve is used to drain any condensation that has collected inside the tank to prevent the tank from rusting. It is not part of a kit or assembly, is sold individually, made of brass, is gold, and will be found at the bottom of the air tank.
This part will need to be replaced when it is no longer able to provide a proper seal, or if it is visibly worn or damaged. You will need a wrench to complete this repair.
Customers rate this repair as Easy.
Fixes these symptoms
- Air leak
- See more...
Your Price
$23.82
In Stock
Black and Decker Sa Gear And Spindle, Serv Only
Opened motor head. Remove 7 torx screws
Opened split housing using a small straight slot screw driver.
Removed gear from housing and pulled it out the bearing housing.
Opened split housing on trigger end. 8 torn screws.
Opened split case with flat screw driver.
Removed motor connections in trigger end for motor.
Pulled motor cable and motor from extention tube.
Please note tube orientation for easy reassemble.
Install new cable/motor on trigger end. Reinstall housing on trigger end.
Install new motor and gear head into new housing. Be sure to install old electrical brace stop to protect new cable.
Roll gear head to verify easy non-binding rotation.
Install top of split case for motor/head end.
Reinstall line guard and line guide.
Test with battery to proof the assembly Read more...
PartSelect Number PS18994000
Manufacturer Part Number N498091
This is a Genuine OEM Sourced replacement part designed for Black and Decker String Trimmer. This item is used to secure and drive the Spool. It is made out of Plastic and Metal. Includes a Plastic Housing, Plastic Gear, Metal Bearing and Two (2) Metal Eyelets.
Fixes these symptoms
- Cutting line does not come out
- Engine revs but trimmer head will not turn
- See more...
Installation Instructions
Mark from CATOOSA, OK
Bearings on motor armature were shot ... driver gear not turning driven gear.
Took off line guard and guide. Remove 1 Phillips screw.Opened motor head. Remove 7 torx screws
Opened split housing using a small straight slot screw driver.
Removed gear from housing and pulled it out the bearing housing.
Opened split housing on trigger end. 8 torn screws.
Opened split case with flat screw driver.
Removed motor connections in trigger end for motor.
Pulled motor cable and motor from extention tube.
Please note tube orientation for easy reassemble.
Install new cable/motor on trigger end. Reinstall housing on trigger end.
Install new motor and gear head into new housing. Be sure to install old electrical brace stop to protect new cable.
Roll gear head to verify easy non-binding rotation.
Install top of split case for motor/head end.
Reinstall line guard and line guide.
Test with battery to proof the assembly Read more...
Your Price
$12.14
In Stock
Black and Decker Brush
PartSelect Number PS12410247
Manufacturer Part Number 445861-25
(Sold Individually)
This motor brush is for grinders.
The motor brush transfers electric current to the spinning armature in the motor.
Unplug the grinder before installing this part. Wear work gloves to protect your hands.
Your Price
$6.40
In Stock
Black and Decker Bolt Assy
PartSelect Number PS12530513
Manufacturer Part Number N436564
This is a genuine Dewalt replacement part, it is sold individually. The purpose of this bolt is to secure the blade on the miter saw models shown below. It has a 1/2 " hex head. It is 1 inch long, with left hand threads.
Related Black and Decker Parts
- Black and Decker Chainsaw Parts
- Black and Decker Cooler Parts
- Black and Decker Edger Parts
- Black and Decker Generator Parts
- Black and Decker Hand Vacuum Parts
- Black and Decker Heater Parts
- Black and Decker Hedge Trimmer Parts
- Black and Decker Lawn Mower Parts
- Black and Decker Leaf Blower / Vacuum Parts
- Black and Decker Nailer Parts
- Black and Decker Planer Jointer Parts
- Black and Decker Pole Saw Parts
- Black and Decker Pressure Washer Parts
- Black and Decker Sprayer Parts
- Black and Decker Tiller Parts
- Black and Decker Trimmer Parts
- Black and Decker Upright Vacuum Parts
- Black and Decker Utility Vacuum Parts
Popular Black and Decker Models
Below are the most popular Black and Decker models we have. Enter your model number in the search box to find your model.