Thermador Refrigerator Ice Makers

Videos!

Your Price

$147.07

Thermador Refrigerator Replacement Ice Maker

★★★★★

219 Reviews

PartSelect Number PS358591

Manufacturer Part Number 4317943

This ice maker (Complete Icemaker Assembly, Whirlpool Icemaker Kit, Ice Maker Assembly, Refrigerator Ice Maker, Icemaker) receives water from the water inlet valve, freezes it, and dispenses it into the ice bucket until the bucket is full. Ice makers will need to be replaced every 3-10 years depending on the frequency of usage, and water quality. You can perform a voltage test with a multimeter or perform an inlet valve test. If you’re unable to make ice, or notice leaks then it may be a sign your ice maker is damaged and could be in need of a replacement. This model measures approximately 11x5 inches, is constructed of plastic and metal, and comes in black/silver. This ice maker is a complete assembly; the whole assembly attaches to the wall of your freezer.

Fixes these symptoms

Ice maker dispenses too little ice
Ice maker dispenses too much ice
Ice maker not making ice
See more...

Installation Instructions

GLENN from ORLAND PARK, IL

was not making ice

take out ice bucket, just loosen the top 2 screws, remove the bottom screw, slide ice maker up & out, srewdriver to release wiring harness clip, reverse to put back in. was very simple. did not install water inlet kit yet. water under fridge stopped after i changed the ice maker. Read more...

Your Price

$28.52

Thermador Refrigerator Coupling

★★★★★

3 Reviews

PartSelect Number PS11739763

Manufacturer Part Number WP2220458

This coupling is used for indoor ice dispensers.

Fixes these symptoms

Ice maker not making ice
Ice maker won’t dispense ice
See more...

Installation Instructions

patrick from fairfax, VA

ice maker gear broken

I removed the ice bucket,the gear is located under the ice bucket and engages when ice bucket sits on it and turns the tray for ice to fall in the shute,2 screws to remove and the gear comes off and I put the new one on and put the screws back,very easy to do, total time 5 minutes,repair man wanted to charge $114 for the part and $100 for labor,I did it all for $25 thru this site,I love this site,it gsaved me alot of money,thanks partselect., Read more...

Videos!

Your Price

$118.52

Thermador Refrigerator Icemaker Control Assembly

★★★★★

26 Reviews

PartSelect Number PS2341896

Manufacturer Part Number W10190935

The “Icemaker Control Assembly” (Module & Motor Assembly, Ice Maker Control Module, Icemaker Module, Refrigerator Ice Maker Module) is what controls the actions of your ice maker. The control turns the timing cams and the ejector blades. It controls most of the basic parts and functions such as the heater, water inlet valve, the cube size, and cube ejection. If your ice maker control is broken it can no longer properly control the ice maker functions. It may not produce any ice, make small ice cubes, or have intermittent operation. This can occur due to normal wear and tear. The icemaker control assembly is attached to the ice maker mold, and is under the white cover. Test the icemaker control assembly by using a multimeter. If this reveals the assembly to be defective, you will need to replace this part. It is approximately 4.25 inches square, beige, and is constructed of plastic and metal. This replacement part features one icemaker control assembly, including the control module and the motor.

Fixes these symptoms

Ice maker not making ice
Ice maker won’t dispense ice
Leaking
See more...

Installation Instructions

Daniel from Suwanee, GA

No ice

removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. Read more...

Videos!

Your Price

$26.75

Thermador Refrigerator Ice Bin Coupling

★★★★★

13 Reviews

PartSelect Number PS11739762

Manufacturer Part Number WP2220457

This part is located at the bottom of the ice bucket.

Fixes these symptoms

Ice maker not making ice
Ice maker won’t dispense ice
See more...

Installation Instructions

Dan from Huntington Beach, CA

The bin coupler broke in half

When I inspected the ice bin I noticed the bin coupler was in half. So I ordered the part. I removed the screw that held in the old part. I saved the two washers. Simply following the diagram on the website made reassembly a piece of cake. It is obvious which piece is the coupling as only it can fit the other coupling. I put the screw back in and it was done. Read more...

Videos!

Your Price

$116.11

Thermador Refrigerator Icemaker Motor Kit

★★★★★

8 Reviews

PartSelect Number PS733947

Manufacturer Part Number 8201515

This kit includes the module motor, ejector arm, and ice stripper arm. The complete icemaker is sold separately.

Fixes these symptoms

Ice maker not making ice
Ice maker won’t dispense ice
See more...

Installation Instructions

ANDREW from DURANGO, CO

KITCHEN AID SIDE-BY-SIDE REFRIGERATOR ICE-MAKER stopped working due to a broken motor assembly.

Changing the KITCHENAID MOTOR ASSEMBLY TO THE ICE-MAKER was fairly straightforward. The hardest part was figuring out WHAT was broken and how to fix it. I was determined to save myself hundreds of dollars by doing it myself and avoiding a visit by the 'repairman'.

1.) Went to KitchenAid website to look at Parts List for my side-by-side refrigerator and ice maker assembly (a PDF file, easily downloadable) . The illustrations helped me visualize the assembly and various parts involved.
2.) Removed cover on front of ice maker.
3.) Removed hex-head screw on undersurface of icemaker on the right, which stablilizes a plastic cover for the electrical connector to the ice maker. Once this is off, it's then possible to slide the ice maker out.
4.) Slide the ice maker out from it's 'shelf' in the freezer. You won't be able to completely remove it until you disconnect the power supply.
5.) Disconnect the multi-pin power connector. (It's probably safest to unplug the refrigerator altogether before doing this, but I did not. No exposed metal wiring or connectors. No problems when I did it this way.)
6.) Once the ice-maker was out, remove the white cover from the motor assembly (on the left side of the unit).
7.) Remove the three screws from the black housing of the motor assembly. (This is where I discovered that the connector between the motor and drive-train was broken and needed to be replaced.)
8.) Remove and replace the drive system for the ice cube ejector.
9.) Then reverse the steps to reassemble.

This may seem a bit vague, but it's really quite straightforward once the ice maker is out of the freezer. The replacement motor assembly includes the motor, the motor housing, the drive-train, and the ice-cube ejector. Very easy to re-asemble.

Shopping for and ordering the part took some time since there are so many different after-market parts dealers. In all honesty, I'm glad I decided on PartSelect.com. They had a decent price, safe checkout, and timely delivery. All the essentials of a good online store.

Thanks, and good luck to the next guy who has to deal with a KitchenAid snafu. Read more...

Videos!

Your Price

$165.75

Thermador Refrigerator Ice Mold

★★★★★

13 Reviews

PartSelect Number PS11749915

Manufacturer Part Number WPW10190929

This is an ice maker mold and heater assembly for a refrigerator ice maker. It is used with modular style icemakers and is located in the freezer section of the refrigerator. This ice mold is flake resistant which prevents the coating on the mold from flaking into the ice cubes when the ice mold begins to wear. The ice mold forms the ice cubes and the heater allows the ice cubes to fall from the ice mold to drop them into the ice bucket. You will need to remove the ice maker from the refrigerator to access the mold and heater assembly. This is a genuine replacement part.

Fixes these symptoms

Ice maker not making ice
Leaking
See more...

Installation Instructions

George from Cottage Grove, MN

Ice maker mold was cracked and leaking water into the bin which then froze all the cubes together.

I removed the ice maker assembly from the freezer compartment (four nuts/ nut driver) and unplugged the wire harness. I discovered the nature of the problem and I went on the Internet to look for replacement parts expecting I'd have to buy the entire ice maker. When I found PartSelect.com I looked through the pictures of the parts available for my ice maker. I found the correct part quickly and easily. And having an acurate photo on the site, I was able to match all the key features of the mold I had with the one on the screen. I ordered the part, and installed it the day it arrived with just a Phillips screwdriver and a nut driver. It functions perfectly. Read more...

Videos!

Your Price

$50.37

Thermador Refrigerator Stripper Arm Kit

★★★★★

8 Reviews

PartSelect Number PS2378115

Manufacturer Part Number W10297244

This kit includes the stripper arm and fill cup.

Fixes these symptoms

Ice maker not making ice
Ice maker won’t dispense ice
See more...

Installation Instructions

Mark from Newtown, PA

Ice Maker stripper arm cracked

This was a pretty easy repair...I removed the retaining screws and slid the assembly off its tracks. Disconneting the wiring hardness was a pain but after a few minutes I had that off (use gloves, it gets cold in the freezer after a minute)

Once I had the unit completely out of the freezer the replacement part took only minutes to replace.

Reversed the process putting the ice maker back in - a few hours later my ice buck was full again.

Simple repair - well worth the effort. Read more...

Videos!

Your Price

$40.40

Thermador Refrigerator Water Fill Cup and Bearing

★★★★★

10 Reviews

PartSelect Number PS11743318

Manufacturer Part Number WP628356

This refrigerator ice maker fill cup dispenses the water into the ice cube mold during the fill cycle. Replacing the water fill cup is a possible solution if you notice that the ice maker is leaking, or not making/dispensing ice. If you notice the fill cup has been damaged or cracked; replace the part straight away. This water fill cup is a genuine OEM part and will fit most refrigerators, but check the list of compatible brands to make sure yours is included before purchasing.

Fixes these symptoms

Ice maker dispenses too much ice
Ice maker not making ice
Ice maker won’t dispense ice
See more...

Installation Instructions

David from Chester, CA

The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.

I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover which is snapped in place, then removing two recessed screws at the front. I removed the broken part, I then reassembled the ice maker with the new part. I replaced the two recessed screws at the front and snapped on the cover. Then I reinstalled the ice maker in the refrigator by plugging in the harness, slipping the ice maker over the loosened screws in the refrigerator and replacing the screw that was removed from the underside bracket. Tightening all the screws completed the project. Read more...