Refrigerator Motors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Refrigerator Motors
Your Price
$71.27
In Stock
Refrigerator Evaporator Fan Motor
PartSelect Number PS12741350
Manufacturer Part Number WR60X31522
This 115-volt 60Hz evaporator fan motor is located in the back of the freezer and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. If the motor has failed, the freezer/refrigerator will become too warm because the fan motor is not circulating the cool air from the freezer into the refrigerator. This is a genuine OEM part. Please remember to disconnect the power to the appliance before starting your repair.
Fixes these symptoms
- Clicking sound
- Freezer section too warm
- Fridge and Freezer are too warm
- See more...
Installation Instructions
Luis from College Station, TX
Freezer Fan
I removed two srews from the back panel inside fthe reezer compartment and the two that hold the air manifold/baffle? and pulled the baffle out. Then, I removed the two srews that hold the front part of the fan bracket behind the baffle and the back panel came out easily. Two more screws and one quick connect plug attached to the fan and I was done with removal. Insallation was even quicker, I slid the original fan right off the old motor and slid it on the new motor's shaft. Piece of cake! Thanks Partselect.
Read more...
Your Price
$97.95
In Stock
Refrigerator Drive Motor With Pulley
1) Removed back - 6 screws
2) Removed dryer vent - 2 screws on top, 3 on bottom
3) Popped the top open
4) Removed Front of dryer cabinet - 2 screws
5) Removed Belt
6) Removed Drum
7) Cleaned up all lint
8) Pop off motor retainers front and back
Here is the tricky part for me.
9) Removed vent fan on back of motor.
I did not know that the back of the fan was square, and you could put an open ended wrench on it to hold it while you also have a vice grip on the front motor shaft. Then its a simple left to loosey operation. I first tryed to turn the fan blade to take it off, but proved to be to tight.
10) Repeat backwards to reassemble
While I had it apart I also replaced the Drum support rollers & Installed a new belt. Not that diffucult of a repair Good Luck, was certainly better than buying a new one at + $300.00 at Black Friday rates. Read more...
PartSelect Number PS334304
Manufacturer Part Number 279827
This OEM drive motor is designed to operate the drum in electric and gas dryers by turning the drive belt, enabling proper rotation during drying cycles. Compatible with most Whirlpool-incorporated dryer brands manufactured before 1996, it includes a pre-attached pulley, which is not available separately. If the motor has shorted out or failed, the drum will no longer spin, and replacement is necessary to restore full functionality. Installation requires disconnecting the dryer from its power source before removing the old motor and installing the new one. This component is sold individually and meets original equipment standards for performance and reliability.
Fixes these symptoms
- Drum Not Spinning
- Noisy
- Will Not Start
- See more...
Installation Instructions
Mark from Fremont, NE
Wife told me Dryer would make a funny sound, then stop + had an a funny smell as well. The Electric motor that drove the unit was overheating and locking up, It was time to be replace.
The best part of my repair was I had everything back in service in 3 days. And one of these days was to consider just buying a new dryer. Had parts overnited and all parts fit and easy to replace.1) Removed back - 6 screws
2) Removed dryer vent - 2 screws on top, 3 on bottom
3) Popped the top open
4) Removed Front of dryer cabinet - 2 screws
5) Removed Belt
6) Removed Drum
7) Cleaned up all lint
8) Pop off motor retainers front and back
Here is the tricky part for me.
9) Removed vent fan on back of motor.
I did not know that the back of the fan was square, and you could put an open ended wrench on it to hold it while you also have a vice grip on the front motor shaft. Then its a simple left to loosey operation. I first tryed to turn the fan blade to take it off, but proved to be to tight.
10) Repeat backwards to reassemble
While I had it apart I also replaced the Drum support rollers & Installed a new belt. Not that diffucult of a repair Good Luck, was certainly better than buying a new one at + $300.00 at Black Friday rates. Read more...
77% OFF
Your Price
$19.94
$85.45
In Stock
Refrigerator Evaporator Fan Motor
Empty the freezer and remove the two screws that hold the back panel of the inside of the freezer on. Pull the panel out and you will see the fan that is mounted to the back of the panel. If the fan is not running, disconnect it (quick connector) and check to see if there is voltage coming to it from the connector (should be 120VAC between the two wires). If there is power, and the fan was not working, replace the fan.
Fan just snaps into the holder on the back panel and plugs into the quick connector. Make sure you clear any ice build-up in the hole between the freezer and the frig that the fans blows through. Put it back together and verify the fan runs. Read more...
PartSelect Number PS12728811
Manufacturer Part Number 242077705
This blower motor, also known as an evaporator fan motor, is a genuine OEM replacement designed for select refrigerator models. It features a 3-wire connector and powers the internal fan responsible for circulating cold air throughout the fresh food compartment. By maintaining consistent airflow, it supports efficient cooling and helps regulate internal temperature. A malfunctioning motor may result in uneven cooling, warm spots, or excessive frost buildup. Installation should be performed with the appliance unplugged, and model compatibility must be verified prior to purchase.
Fixes these symptoms
- Freezer section too warm
- Fridge and Freezer are too warm
- Fridge too warm
- See more...
Installation Instructions
Roger from TRURO, IA
Refrigerator not cooling, Freezer working fine
Frig area was at about 50 degrees and would not get cooler. Freezer was working great. Empty the freezer and remove the two screws that hold the back panel of the inside of the freezer on. Pull the panel out and you will see the fan that is mounted to the back of the panel. If the fan is not running, disconnect it (quick connector) and check to see if there is voltage coming to it from the connector (should be 120VAC between the two wires). If there is power, and the fan was not working, replace the fan.
Fan just snaps into the holder on the back panel and plugs into the quick connector. Make sure you clear any ice build-up in the hole between the freezer and the frig that the fans blows through. Put it back together and verify the fan runs. Read more...
Your Price
$75.74
In Stock
Refrigerator Refrigerator Fresh Food Evaporator Fan Motor (dc)
Plugged in refrigerator to make sure it would work. After 15 minutes, unplugged fridge and put rails and drawers back. Total time 45 minutes. Plugged refrigerator back in and let run 24 hours.
It took 5 days to get part due to snow storm delaying delivery. It works perfectly. Our GE will be 10 years old in August. Read more...
PartSelect Number PS12172983
Manufacturer Part Number WR60X26866
This evaporator fan motor is a critical component in GE refrigerators, designed to circulate cold air over the evaporator coils and distribute it evenly throughout the fresh food and freezer compartments. Operating as a DC motor, it ensures consistent internal temperatures by drawing air across the cooling coils and pushing it through the unit. Engineered with high-quality materials, it delivers long-lasting performance and quiet operation. While primarily used in GE models, it is also compatible with select units from Hotpoint, Café, and Monogram. Replacing a faulty motor can resolve issues such as poor cooling, frost buildup, or unusual noises, restoring optimal airflow and refrigeration efficiency.
Fixes these symptoms
- Fridge too cold
- Fridge too warm
- Noisy
- See more...
Installation Instructions
Eunice from POWELL, WY
The refrigerator was too warm. The drawers where vegetables and fruits are kept were being frozen. The vents blowing cool air into bins were iced up.
Took the drawers out of fridge and unscrewed the support rails for drawers and unscrewed inside back wall of fridge. Removed cover on blower fan ~ unplugged fan. This took 45 mins. Left refrigerator unplugged and let thaw out. Replaced with new fan 5 days later. Plugged in new fan. ThenPlugged in refrigerator to make sure it would work. After 15 minutes, unplugged fridge and put rails and drawers back. Total time 45 minutes. Plugged refrigerator back in and let run 24 hours.
It took 5 days to get part due to snow storm delaying delivery. It works perfectly. Our GE will be 10 years old in August. Read more...
Your Price
$94.95
In Stock
Refrigerator Condenser Fan Motor
(cardbord) the fan will come off and go back on by hand no tools needed i changed the fan motor just to be sure. 3 little screws hold it on. the plug only goes on one way u can't mess it up.very easy job u shouldn't have any problems doing it.Jim Read more...
PartSelect Number PS3501052
Manufacturer Part Number 242018301
This condenser fan motor is a genuine replacement part designed for select refrigerator models. It drives the fan blade to circulate air across the condenser coils, helping cool the refrigerant and maintain optimal temperatures in both the freezer and fresh food compartments. Proper airflow is essential for efficient cooling, and a faulty motor may result in poor performance, excessive noise, or temperature fluctuations. This OEM component is compatible with various models and replaces several part numbers. Sold individually.
Fixes these symptoms
- Freezer section too warm
- Fridge and Freezer are too warm
- Fridge too warm
- See more...
Installation Instructions
James from GLEN FLORA, TX
Plastic fan broke
took the cover off(cardbord) the fan will come off and go back on by hand no tools needed i changed the fan motor just to be sure. 3 little screws hold it on. the plug only goes on one way u can't mess it up.very easy job u shouldn't have any problems doing it.Jim Read more...
Your Price
$52.27
In Stock
Refrigerator Freezer Evaporator Fan Motor
PartSelect Number PS11740359
Manufacturer Part Number WP2315539
This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.
Fixes these symptoms
- Freezer not defrosting
- Freezer section too warm
- Fridge and Freezer are too warm
- See more...
Installation Instructions
William from Middletown, NY
Evaporator Fan failure
The reason I repaired it myself was because the repairman that diagnosed the problem.didn't come back in two weeks. The evaporator fan sits behind a vented wall in the freezer and directs cold air into freezer and refrigerator.I removed the ice make assembly first and then the freezer wall held in place by two sheet metal nuts. Then removed wires from fan motor. Removed the fan blade from fan motor,which was press fitted on,then removed fan motor from bracket assembly(make sure and retain the two vibration rubber washers on back and front of motor. Reinstall new motor with vibration washers and press fan blade on new motor. Install in bracket assemble and reassemnble.
Read more...
Your Price
$56.22
In Stock
Refrigerator Evaporator Fan Motor (115v)
PartSelect Number PS3502361
Manufacturer Part Number 297309000
This evaporator fan motor is 115V. If you notice that your freezer is noisy or is too warm, you may need to replace the evaporator fan motor. This package comes with the evaporator fan motor itself, as well as a wire harness. The evaporator fan motor is in the back of the freezer, so you will need to remove your freezer shelves and the back panel before you can access it. The function of the evaporator fan motor is to circulate air over the coils. The coils convert the heat into cool air, which is then circulated. Be sure to remove the power source from the freezer before you begin this repair.
Fixes these symptoms
- Fridge too warm
- Frost buildup
- Noisy
- See more...
Installation Instructions
Nathan M. from Bunnell, FL
Freezer thawing at about 20 degrees
Turned freezer off at themostat and unplugged freezer. Removed 2 screws at front 2 at the back and 2 at the top. Lowered top cover and removed evaporator fan bracket (2 more screws) removed themostat capulary tube( 1 screw and bracket) then unplug fan motor. Removed motor from bracket (2 screws). Put on new fan motor then removed fan blade from old motor and put on the new motor. Remounted fan motor bracket and thermostat capulary tube. Remounted top cover, plugged freezer in the set the thermostat to 4 and freezer is working fine and doing its job. I orderedmotor on a Sunday and it was shipped on Monday and I received said part at 7:pm on Wednesday.
Read more...
Your Price
$58.20
In Stock
Refrigerator Evaporator Fan Motor Kit - 120v 60hz
PartSelect Number PS3419839
Manufacturer Part Number 5303918549
The evaporator fan motor (Motor Evaporator Fan, Evaporator Fan Motor Kit, Evaporator Fan Motor, Refrigerator Evaporator Fan Motor) circulates air through the food compartment for efficient cooling in refrigerators. The evaporator fan motor can squeal as its bearing dries out. The motor bearings can totally seize, preventing any movement. The motor coil can also burn out, preventing any fan movement. If this motor fails, the refrigerator compartment will warm up and eventually the freezer will reduce cooling as well. Excessive frost can build up on the evaporator coil due to lack of air movement. The motor can make a squealing noise when it is beginning to fail or will not operate at all when powered, and this is a sign it should be replaced. The evaporator is located in the rear of the freezer compartment. This part measures 2-1/2 inches wide by 3 inches tall by 1 inch thick, at its widest point. It is constructed of plastic and metal, and comes in black/silver. This kit includes the evaporator fan motor and harness.
Fixes these symptoms
- Freezer section too warm
- Fridge and Freezer are too warm
- Fridge too warm
- See more...
Installation Instructions
Larry from Carthage, NC
bottom of fridg. would not get cool. Temp was 50-60degrees. The freezer compartment worked so I knew it was not the compressor.
I removed the fan housing in the freezer section by removing all the screws. (7) There are two screws behind the vents. I did not have an ice maker to contend with so this was very easy. There is only two wires to disconnect....the ground wire and the electricity supply. Then you remove the unit from the back of the housing cover by removing two screws. Then the motor is removed from it's housing by removing 2 more screws. 1...2...3 and you're ready to reverse the procedure. I am not mechanically inclined and this was easy. Saved myself perhaps $120.00. Repair folks wanted mininum of $60.00 just to come out. Part and shipping cost me 33 bucks.OH, DON'T FORGET TO UNPLUG THE FRIDGE. :>)
Read more...
Your Price
$62.15
In Stock
Refrigerator Condenser Fan Motor Kit
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire about two inches from the fan.
Cut and strip the new wire. I cut the new wire in half (about 6 inches.) Connect the two wires, twist and used 2 wire nuts. Tie wrap the wire to the wire harness. Mount the new fan (three screws)
Screw the back panel back on.
Mount the new Read more...
PartSelect Number PS395284
Manufacturer Part Number 833697
This condenser fan motor kit is designed for use with refrigerators. This fan draws air through the condenser coils and over the compressor. It does this with the goal of cooling the warm refrigerant before it enters the evaporator. When your fan or fan motor is not working your refrigerator will not cool properly. This is a 2-Watt, 115 Volt motor that rotates the fan in a counter clockwise direction. This kit includes the hardware needed for installation, and a set of instructions. Before you begin any repair work make sure to unplug your appliance.
Fixes these symptoms
- Freezer section too warm
- Fridge and Freezer are too warm
- Fridge runs too long
- See more...
Installation Instructions
Tom from Franklin, WI
Sometimes the condenser fan would start causing the refrigerator to overheat.
Unplug the appliance.Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire about two inches from the fan.
Cut and strip the new wire. I cut the new wire in half (about 6 inches.) Connect the two wires, twist and used 2 wire nuts. Tie wrap the wire to the wire harness. Mount the new fan (three screws)
Screw the back panel back on.
Mount the new Read more...
Your Price
$50.30
In Stock
Refrigerator Evaporator Fan Motor
PartSelect Number PS11749890
Manufacturer Part Number WPW10189703
This is a 60 Hertz, 120-volt evaporator fan motor for your refrigerator. This part is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. The most common reason for needing to replace the motor is if the temperature in your freezer and fridge are inconsistent, or there is no air circulating at all. You will need a quarter inch nut driver and a pair of needle nose pliers for this repair. Note: This motor uses 2 brackets, which are sold separately.
Fixes these symptoms
- Freezer not defrosting
- Freezer section too warm
- Fridge and Freezer are too warm
- See more...
Installation Instructions
Brian from Smock, PA
Fridge was warm. No air circulating at all. Food was spoiling Fridge was just over 1 year old
First I removed the two screws that secure the guard in bottom back of the freezer and removed it . Next I removed the two screws that secure the guard on the back wall of the freezer and removed it. There are three wires connected to the motor, I unplugged those and removed the two screws that secure the motor and removed it. I swapped the grommets, blade and support bracket from the old motor. I put it back together in reverse steps and its working great. My mother-in-law can,t stop thanking me ! I saved her at least $400 to buy a new fridge. Thank You, Brian Miner
Read more...