Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
JOHN Z - September 18, 2022
Verified Purchase
Great Part! Fixed the problem.
After doing some research on-line, this part had a 99% rating of being the cause for my dishwasher not to turn on. I do not have a multi-voltmeter to perform the required testing that is shown on You Tube to confirm that this ,in fact, the part failure. I liked my odds so I purchased the product. Other than a mistake in the You Tube video which showed that you had to release a small tab with a screwdriver to remove this part (actually was held in place by a phillips screw),the part was easy to install. Once I turned the power back on, the dishwasher started to work in it's cycle when the part had failed. Has been working properly for over 3 weeks and is quiet just as it was when first purchased.
★★★★★
★★★★★
Denise S - August 7, 2020
Verified Purchase
Finally washer is working!
It worked and my washer is up and running. The repair told us it was the mother board,which was wrong and the we traced back to this part. Very happy!
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
No power to dishwasher. Confirmed that outlet had power coming out.
Turn off circuit breaker. Turn off water at shutoff valve usually located under sink. Disconnect water line from dishwasher. Disconnect wires for the power feed from cord, Marked corresponding wires upon removal for re-installation. Remove 2 mounting screws that secure dishwasher to counter. Slide dishwasher out from counter and turn upsi
... Read morede down. Use a blanket to prevent scratching of surfaces. Locate component on the back portion of the dishwasher. Unplug 2 wiring harnesses. My part was held on by 2 phillip screws. One in front, the other in the back along the leg bracket support. Once removed, reverse the order of removal. The i a You Tube video you can locate fr this removal. They said that you needed to release a clip to get the part out. Mine had a screw holding it on the back side. This difference cause about an extra 1/2 hour before I was able to figure out that there was NO clip that was being shown on the video. After that, The replacement went smoothly and we were having the dishes washed later that day.
Read less
JOHN from FORT MYERS, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
7 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Douglas
September 1, 2017
Will not power on,I checked noise filter seems fine! 120v going in 120v coming out
For model number WM3455HS
Hi Douglas,
Thank you for the question. The locker switch assembly may be defective. The locker switch assembly is a part for your washing machine and tells the washer that the door is closed and locked into place. If the switch has shorted out and not locking, it is no longer delivering the message to the machine and it will not latch into place. If you find that your door will not close, open, or start, it is more than likely an issue with the locker switch assembly. The switch is located behind the front panel. You will need to remove the gasket to reach the switch.
Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Devon
January 14, 2019
Dishwasher has three light bar on screen but won't start its an LG
For model number LDS5540ST
Hello Devon, Thank you for the question. I suggest testing the switches on the door lock, PartSelect Number PS5574492. If the switches can not recognize the door is closed it will not allow it to start. Hope this helps, good luck with this repair!
The lights on the top do not come on when pressed. There is 110 going to the unit. What do I need to check?
For model number LDT99656BD
Hello Jim, thank you for your question. We have researched your model and found that the most likely fix to your problem is to change the noise filter, part number PS3528920. If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
1 person found this helpful.
Was this helpful?
Thank you for voting!
DONALD
April 7, 2023
On/Off button works sometimes and but mostly it doesn't no matter how many times it is pushed. All other switches work as advertised.
For model number wm2140cw
Hello Donald, thank you for contacting us. Based on our research, if the on/off button is not working, you may need to check the display power control board, part number PS3623244, to fix the issue. Before replacing the control board you may need to check whether the start button is properly pressed or not. We hope this solves your problem!
I am having trouble with my washer/dryer combo unit. It started with the machine randomly turning on and off during spin cycle. Found wires chaffed and shorting on metal, repaired. Machine ran for 3 separate wash cycles after last cycle machine found not turning on. Found fuse on main board blown. Replaced board machine ran two more wash cycles, failed to turn on after last cycle, fuse blown again. Checked for shorted wires and components, things appear good.
Any recommendations on what direction I should proceed.
For model number WM3987HW
Hello Jeremiah, thank you for your inquiry. You may need to check the noise filter, part number PS3528920. If it is faulty, then you may need to replace it to fix the issue. We hope this solves your problem!
Was this helpful?
Thank you for voting!
Greg
March 23, 2024
Machine trips GFI during pump cycle. Is my pump bad?
For model number LDF9810ST
Hi Greg, thank you for your inquiry. Based on our research, the issue is with drain pump, part number PS16223509. You may need to replace the drain pump to fix the issue. Glad to be of assistance!
No power to unit. Wife said she smelled something burning and dishwasher shut down before she came out to investigate. Control panel or noise filter?
For model number LDF7774ST
Hello Scott, thank you for writing. We recommend checking to see if anything had fallen on the heating element PS7788065 like food debris or a plastic item. If the burning smelled " electrical" then it may be Electronic Control PS11710963. We hope this helps.
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Washer","title":"Washer","url":"/Washer-Parts.htm"},{"position":2,"name":"Circuit Board or Touch Pad","title":"Circuit Board or Touch Pad","url":"/Washer-Circuit-Boards-and-Touch-Pads.htm"},{"position":3,"name":"6201EC1006T","title":"6201EC1006T","url":""}]
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
