EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

79640441900 Kenmore Washer - Overview

Diagrams for 79640441900

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing Machine Drain Pump – Part Number: 4681EA2001T
$61.55
In Stock
Washing Machine Drain Pump
★★★★★
★★★★★
(315)
Part #4681EA2001T
The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small flat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse order -- taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.
Water Inlet Valve - Hot – Part Number: 5220FR2006H
$37.35
In Stock
Water Inlet Valve - Hot
★★★★★
★★★★★
(94)
Part #5220FR2006H
Hot water enters the washer through this single solenoid inlet valve, which opens when the control calls for hot water and closes when filling stops. It connects the household hot water supply to the internal fill system, regulating flow during selected wash cycles. A faulty valve may prevent hot water from entering, cause slow filling, or allow water to seep into the tub while the washer is off. Replacing a damaged valve helps restore controlled filling and proper shutoff of the hot water supply. This is an OEM part sourced directly from the manufacturer.
Rear Tub Gasket – Part Number: 4036ER2004A
$36.25
In Stock
Rear Tub Gasket
★★★★★
★★★★★
(15)
Part #4036ER2004A
Protecting the tub bearings from wash water, this rear tub shaft seal forms a barrier around the rotating drum shaft. The rubber seal fits into the rear outer tub and helps keep water and detergent away from the bearing area while the drum turns. A worn, torn, or hardened seal may allow leaks near the rear of the tub and expose the bearings to moisture. Replacing a damaged seal restores the barrier needed to contain wash water and protect the drive shaft bearing area. This is an OEM part sourced directly from the manufacturer.
Tub-to-Pump Drain Hose – Part Number: 4738ER1002A
$66.13
In Stock
Tub-to-Pump Drain Hose
★★★★★
★★★★★
(16)
Part #4738ER1002A
Water leaves the washer tub through this flexible tub-to-pump drain hose before reaching the drain pump housing. Its corrugated bellows section bends with tub movement, helping maintain the connection during washing and spinning. Cracks, punctures, or worn folds may allow water to leak beneath the appliance, while a collapsed section can restrict drainage. Replacing a damaged hose restores the enclosed path between the tub and pump, helping water drain properly while accommodating movement between the suspended tub and the pump assembly. This is an OEM part sourced directly from the manufacturer.
Door Lock Assembly – Part Number: EBF49827801
$82.45
In Stock
Door Lock Assembly
★★★★★
★★★★★
(29)
Part #EBF49827801
Secure door locking allows a front load washer to begin and complete its cycles. This door lock and switch assembly holds the door closed during operation and reports its status to the main control board. A failed lock or internal switch may prevent a cycle from starting, trigger a door fault message, or keep the door from unlocking after the cycle ends. Replacing a faulty assembly helps restore reliable locking and status feedback, supporting controlled access to the drum during washing and spinning. This is an OEM part sourced directly from the manufacturer.
SENSOR ASSEMBLY – Part Number: 6501KW2002B
$58.25
In Stock
SENSOR ASSEMBLY
★★★★★
★★★★★
(25)
Part #6501KW2002B
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer pumps but will not spin or agitate, you may have a damaged sensor assembly. This part is sold individually, and is an OEM part sourced directly from the manufacturer. Be sure to shut off the power to your washer before you begin this repair.
Washer Gasket – Part Number: 4036ER4001B
$24.67
In Stock
Washer Gasket
★★★★★
★★★★★
(7)
Part #4036ER4001B
This is a seal for a washer tub. It creates a seal between the front and rear halves of the washer tub to prevent the appliance from leaking. If you notice leakage between the two sections of the tub, you may need to replace this part. Seals can get dry and brittle over time which compromises the integrity of the part and may cause your appliance to leak. This is a genuine replacement part sourced from the original manufacturer. You will need to disassemble the outer panels of the washer to access the tub seal.
Detergent Dispenser – Part Number: 3891ER2003A
$25.83
In Stock
Detergent Dispenser
★★★★★
★★★★★
(20)
Part #3891ER2003A
Liquid detergent stays contained in this removable dispenser cup until water flushes it into the washer during the wash cycle. The blue plastic insert sits inside the main detergent drawer and can be lifted out for cleaning. Cracks, damaged edges, or a missing cup may prevent liquid detergent from being held properly before dispensing. Replacing a damaged insert restores the container used for liquid detergent in the dispenser drawer. Its removable design also makes it easier to rinse away residue that collects with regular use. This is an OEM part sourced directly from the manufacturer.
Washer Hose with Bellows – Part Number: 4738ER1004B
$43.95
In Stock
Washer Hose with Bellows
★★★★★
★★★★★
(12)
Part #4738ER1004B
Water and detergent travel from the dispenser into the washer tub through this flexible rubber dispenser hose. Its bellows folds allow the hose to flex as the tub moves during operation, helping maintain the connection between the dispenser and tub. Cracks, tears, or worn sections may allow water to drip inside the cabinet, especially during filling. Replacing a damaged hose restores the enclosed path that carries the detergent mixture into the wash tub and helps prevent leaks from the hose body. This is an OEM part sourced directly from the manufacturer.
Washer Tub Bearing, Rear – Part Number: 4280EN4001F
$72.00
In Stock
Washer Tub Bearing, Rear
Part #4280EN4001F
Inlet Valve Assembly – Part Number: 5220FR2008F
$141.56
In Stock
Inlet Valve Assembly
★★★★★
★★★★★
(22)
Part #5220FR2008F
Cold water is directed through this washer inlet valve to supply the tub and dispenser during selected cycle stages. Four solenoid coils control separate outlets, opening when the washer requests water and closing when filling stops. A cracked housing or failed valve mechanism may cause leaks, slow filling, or water seeping into the drum while the machine is off. Replacing a faulty assembly helps restore controlled cold water delivery and proper shutoff, supporting normal filling and flushing of laundry products from the dispenser. This is an OEM part sourced directly from the manufacturer.
MOTOR ASSEMBLY,AC,PUMP – Part Number: EAU61383518
$121.09
In Stock
MOTOR ASSEMBLY,AC,PUMP
★★★★★
★★★★★
(3)
Part #EAU61383518
On a washer, this part is used for circulating the water. On a dishwasher, it is used for draining the water during operation. If you notice your appliance is not draining properly, the circulation pump motor may need to be replaced. If this part is for your washer, you may notice your clothes are not cleaning properly. In your washer, to access this part you will need to remove the entire front panel. The circulation pump is 120 volts and 30 watts. The part is white in color and is sold individually. This OEM part comes directly from the manufacturer.

Manuals & Care Guides for 79640441900

Click to download

Questions And Answers for 79640441900

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Carl - For model number 79640441900
July 4, 2023
FE message came on —- water wouldn’t stop coming into the washer
Chris Boyle Profile
Hi Carl, thank you for the inquiry. Based on our research, FE error code indicates that the water is overflowing or leaking. We would recommend checking the water inlet valve assembly, part number PS3527431. It controls the water flow into the washer. We hope this helps!
$141.56
In Stock
Inlet Valve Assembly
2 people found this instruction helpful.
Was this helpful?
Thank you for voting!
Robert - For model number 79640441900
August 21, 2023
Won’t spin, is noisy like gears slipping. Error code OE
Chris Boyle Profile
Hello Robert, thank you for asking. According to our research, the OE error code indicates the washing machine is unable to drain the water used during the wash cycle. We would recommend checking the drain hose to ensure that it is not clogged. If it does not help, you may need to replace the drain pump, part number PS3579318, to resolve the issue. We hope this helps!
$61.55
In Stock
Washing Machine Drain Pump
Was this helpful?
Thank you for voting!
Time Gargan - For model number 79640441900
April 10, 2026
LE error comes on after appliance guy replaced it. Now it is worse than before no water fills up but just a loud noise. Then LE error . Before it would fill up water make loud noise go for a bit stop LE error code.
Chris Boyle Profile
Hello Time, thank you for reaching out. The LE error code indicates a locked drive motor error. Reset the appliance first, if this does not work, check the wire harness connections on the motor and the hall sensor (tachometer). Repair any wiring failures. If the wiring connections are fine, replace the hall sensor, part number PS16556422. We hope this information helps!
$58.25
In Stock
SENSOR ASSEMBLY
Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the 79640441900

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing maching wouldn't drain
592 of 761 people found this instruction helpful.
  • Jorge from Apple Valley, CA
  • Easy
  • 1- 2 hours
  • Screw drivers
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer cam e apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Was this helpful?
Thank you for voting!
LE Error Message and won't spin drum properly
255 of 339 people found this instruction helpful.
  • Mark from Harrisburg, PA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
Was this helpful?
Thank you for voting!
noisy operation, sometimes did not drain, gave OE code
60 of 81 people found this instruction helpful.
  • Michael from RALEIGH, NC
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
Was this helpful?
Thank you for voting!