
Water Inlet Valve - Hot
$
17.64
In Stock



Get this part fast. Average delivery time via standard shipping: 1.8 days.
PartSelect Number PS3527427
Manufacturer Part Number 5220FR2006H
Manufactured by
LG
Product Description
Water Inlet Valve - Hot Specifications
The hot water inlet valve on your washing machine controls the water flow into the washer. This inlet valve has a standard hose fitting inlet and one water outlet. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test your valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 3 inches long x 3 inches wide.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Leaking | Will not stop filling with water | Will not fill with water | No hot or cold water
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
LG, Kenmore.
Part# 5220FR2006H replaces these:
AP4441935, 1268123, 5220FR2006H, 5220FR2006H, 5220FR2006L, 5220FR2006Q
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jim
August 3, 2018
My front load LG washer ,at the end of a cycle the water will start to run and won't stop until i turn the cold water valve to off pos.
For model number Wm0642hw

Hi Jim, Thank you for the email. This sounds like an issue with the Water In let valve. If the valve is stuck open and defective it will allow water to flow through after the cycle ends. Hope this helps!
15 people found this helpful.
Was this helpful?
Thank you for voting!
Gerry
October 28, 2017
Water start to fill up the soap despener with those short blast of water that fill the cup about 3 times and then it stops and water stops going in the cup.So the soap is still left in the dispenser. The tub still fill with water. I can hear it going in
For model number WM2455HW

Hi Gerry,
Thank you for your inquiry. There are some parts that you will need to check to see which one is causing the issue. You will need to check the pressure switch, the water inlet valve, the detergent box assembly and softener cap. I hope this helps. Thank you and have a great day!
12 people found this helpful.
Was this helpful?
Thank you for voting!
Grey
October 7, 2017
What about the cold side. Our washer keeps filling when unplugged and will stop when you turn the cold side off. You don't have to touch the hot shut off. Yes I did check to make sure washer hoses were hooked up correctly.
For model number WM2487HRM

Hi Gary, Thank you for the question. It sounds like the water inlet valve is stuck open on the cold side and is letting water through. To fix this the Inlet Valve Assembly,PartSelect Number PS3527431 will need to be replaced.Hope this helps!
10 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Dasha
February 22, 2018
Hello, the water sometimes flows into the washing machine and sometimes doesn't. This happens with both hot water and cold water. When the water doesn't flow it gives the error message ie, which according to the manual means not enough water pressure. We have excellent water pressure. Why would it be working sometimes and not other? Is this most likely an electrical current issue or defective pump (or something else)?
For model number WM3431HW

Hi Dasha,
Thank you for your question. If you are having an issue with water flowing into the washer, the issue is likely with the water inlet valve and it will need to be replaced. I hope this helps. Thank you and have a great day!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Richard
January 6, 2018
Is the install for hot and cold inlet valve the same install?
For model number WM2016CW

Hello Richard, Thank you for your inquiry. There are installation videos available for both parts on our website. It appears the installation process is similar for both, but since the cold water valve has different solenoids, we would recommend watching the videos for both. I have included the links. Hope this helps!
https://www.partselect.com/PS11728995-LG-5220FR2075L-Water-Inlet-Valve-Cold.htm?SourceCode=4&SearchTerm=WM2016CW&ModelNum=WM2016CW#RepairVideo
https://www.partselect.com/PS3527427-LG-5220FR2006H-Water-Inlet-Valve-Hot.htm?SourceCode=4&SearchTerm=WM2016CW&ModelNum=WM2016CW#RepairVideo
3 people found this helpful.
Was this helpful?
Thank you for voting!
Connie
February 7, 2019
How do i change the inlet filter video?
For model number Wm3488h

Hello Connie, Thank you for the question. Here is a link to the video on youtube. It is also posted on the site. Hope this helps!
https://www.youtube.com/watch?v=MMq7jHIAKZo
3 people found this helpful.
Was this helpful?
Thank you for voting!
Rob
November 20, 2019
No matter the setting machine only dispenses cold water. What part would you think needs replacing?
For model number kenmore 600

Hi Rob, thank you for your question. It is likely you would need to replace your water valve if you are not getting hot water to your appliance. If you would like to test the part the valve can be tested with a multi meter and should be reading between 500 - 1500 ohms of resistance. I hope that helps. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Lisa
October 29, 2019
Based on the troubleshooting info, i think that my inlet valve on my cold water line is defective. Is it a seperate part for the cold and hot water valve, or will the same valve work on both?
For model number WM0642HW!

Hello Lisa, Thank you for the question. The PartSelect Number PS3527429 is for the Cold water and the PartSelect Number PS3527427 is the Hot water. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Christine
May 19, 2019
No hot water filling machine. Confirmed water is hot from wall supply. Replaced hot water inlet valve. Still no hot water filling machine. What else could it be and what should i try next? Thanks.
For model number WM3670HVA

Hi Christine, thank you for your question. If you have replaced the valve and you are still having the issue, then it is likely your electronic control board that is the problem. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Michael
October 31, 2019
My cold water continues to fill even when the machine is off. The hot water does not. Will the valve replacement for hot water fit on the cold water side too?
For model number WM2501HWA

Hello Michael, Thank you for the question. This sounds like the cold water side of the valve is defective so the valve will need to be replaced. Hope this helps!
Was this helpful?
Thank you for voting!
Part Videos
Replacing your LG Washer Water Inlet Valve - Hot
Customer Repair Stories
Average Repair Rating: 4.3 / 5.0, 18 reviews.
What's this?
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Water continued to fill into the drum slowly after the load was done.
Watched a you tube video and followed the instructions. Even had my 11 and 13 yo old help and do most of the work. Very easy to fix both hot and cold inlet at the same time. Didn't know which one was causing the problem so I decided to replace both.
-
Khanh from CHICAGO, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
-
28 of 30 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water was filling continues even the machine was unplugged
I did repaired while looking at video at your site .thanks to your team ..
-
Sanjay from HOLTSVILLE, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
-
Parts Used:5220FR2006H
16 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water was filling the tub when washer was not in use.
I followed the video and my repair went just like the expert showed on the video. The hardest part was pulling the washer away from the wall and getting enough elbow room to be able to work on the washer. I will definitely come back to this site for my next appliance repair.
-
Stephen from BONITA SPGS, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
-
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace leaky water valve
Very simple. Watched video.
Pulled the washer out to get behind it.
Turned off water supply, unplugged it.
Unscrewed the screwesholding the top in place, slid top back, lifted it off.
Used pliers to open the clamps holding the pipes to the valve - one at a time. And fitted the pipes to new valve, one at a time.
SOME WATER REMAINS IN THESE PIPES, SO PUT A TOWEL UNDERNEATH TO CATCH IT.
Removed the electrical connectors one at a time and fitted them to the new valve one at a time.
Did same to the hot valve - not leaking but decided to replace it before it did leak.
Reattached water supply hoses and electric plug.
Tested the washer cycle to make sure no leaks.
Put top back on and pushed washer back to wall.
Apart from the testing, the whole job took 25 minutes.
The parts arrived on Day 2 after the order.
VERY PLEASED WITH EVERYTHING!
Pulled the washer out to get behind it.
Turned off water supply, unplugged it.
Unscrewed the screwesholding the top in place, slid top back, lifted it off.
Used pliers to open the clamps holding the pipes to the valve - one at a time. And fitted the pipes to new valve, one at a time.
SOME WATER REMAINS IN THESE PIPES, SO PUT A TOWEL UNDERNEATH TO CATCH IT.
Removed the electrical connectors one at a time and fitted them to the new valve one at a time.
Did same to the hot valve - not leaking but decided to replace it before it did leak.
Reattached water supply hoses and electric plug.
Tested the washer cycle to make sure no leaks.
Put top back on and pushed washer back to wall.
Apart from the testing, the whole job took 25 minutes.
The parts arrived on Day 2 after the order.
VERY PLEASED WITH EVERYTHING!
-
JOHN from LOVELAND, CO
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
-
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
w/d repeatedly fills with water during warm or hot loads
E. Z. hardest part (which isn't hard) was moving the appliance to reach the back, then putting the appliance back into place. the actual repair (swapping out valve) took less time than that to do.
-
kevin from WASHINGTON, DC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
-
Parts Used:5220FR2006H
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking on the floor under the washer.
Unplug the washer! Turn off the HOT water valve. Remove the hot water hose at the connection on the back of the washer. Remove the two Phillips head screws holding the top of the washer. Slide the lid toward the rear until you feel it disengage, then lift it off, setting it aside.
Unplug the electrical connector on top of the hot water valve (just pulls off).using pliers compress the hose clamp, slide it away from the hot water valve and pull the hose off the valve fitting(it will have some water remaining so lift it up and secure it to the brace above the hoses).
Remove the two phillips head screws that hold the valve in place. Pull the valve toward the front of the washer to remove it and compare it to the new valve.
To install the new valve, reverse all steps insuring tight water hose clamp and electrical connection. Install hot water hose, plug it in and turn on water. Test run and check for leaks. Unplug it and reinstall top.
Unplug the electrical connector on top of the hot water valve (just pulls off).using pliers compress the hose clamp, slide it away from the hot water valve and pull the hose off the valve fitting(it will have some water remaining so lift it up and secure it to the brace above the hoses).
Remove the two phillips head screws that hold the valve in place. Pull the valve toward the front of the washer to remove it and compare it to the new valve.
To install the new valve, reverse all steps insuring tight water hose clamp and electrical connection. Install hot water hose, plug it in and turn on water. Test run and check for leaks. Unplug it and reinstall top.
-
Danny from OAK HILLS, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
-
Parts Used:5220FR2006H
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water was slowly filling up in washer tub, after I would wash clothes 2 or 3 days later there would be water standing in the washing machine.
I looked this problem up on YouTube like I do with everything, I saw a video from this site.. so I ordered what I needed from the website. The parts came in I unpluged the washer from the wall very important, I literally removed 6 Philips head screws and unclipped the wires from the parts and removed the hoses with the pliers, hoses have squeeze clamps. Put in New parts put hoses back on wiring back on and I was done.. it took me a total of maybe 10 minutes.. NO MORE WATER standing in the washer.. Thank you!! I would recommend you add a video for the Inlet Valve Assembly like you have for the hot inlet valve though...
-
Jack from SAN ANTONIO, TX
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
-
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would not fill
Used Youtube to look for a set of repair instructions. From start to end 35 min.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
-
Jesse from CARNEGIE, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
-
Parts Used:5220FR2006H
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hard water scale rendered the valves inoperable
Watched a YouTube video on valve replacement. Then when I knew what to expect, the repair job was a breeze.
-
John from ORR, MN
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
-
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hot water valve was leaking
After I watched the repair video for the part, it was a snap. It went exactly as the video described the steps. Hardest part was moving the washer to get behind it.
-
Rick from KERRVILLE, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
-
Parts Used:5220FR2006H
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Filter By Rating:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Richard S - 11 days ago

fast shipping exact fit easy install
I had a IE code and decided to replace the hot water intake valve first. Everything in the house that had hot water pass through it, seemed to have problems so in my situation I chose this part first. I have not had the time to try it yet install was 5 minutes. I will follow up with the results. Thank you
Jurgen B - 25 days ago

Home repair.
Exactly the part I needed. Arrived quickly. Very satisfied.
Luis C - 27 days ago

Easy repair!
Fast shipping, perfect fit and great quality part.
Thanks!
Rick F - January 15, 2021

Easy repair, part is working great
The part came quickly. I watched the video for making the repair. The repair took hardly any time. Hardest part was moving the washer. I had no idea leaking could occur from this valve. It took me a while to determine where the leak was coming from. I put the new part in and looked for water on the floor after a few washes. No leaking. This part and my time probably saved me $150. I am so glad I found this company and website.
Tracy W - January 14, 2021

Fix it Man
After taking off the top of our washer it was easy to diagnose the issue. This part is what I needed and washer is running again like new.
Melannie G - December 4, 2020

Excellent web site-you make a repair easy.
Part worked great. Easy repair. Went shopping for a new washer because our LG was leaking water. Removed a few screws to look for the leak, and easily saw it was the hot water inlet valve. Your company made finding the part very fast and convenient. Thanks for saving me $1,000 on a new washer.
Rogelio R Q - November 30, 2020

Hot water valve doesnt leak anymore.
Part was good quality & install was quick & easy. Watching video helped a lot.
Carolyn D - November 23, 2020

Easy repair. Worked as intended.
Part was quickly received and washer is up and running.
Paul K - November 13, 2020

Easy and quick
Hot water valve was received quickly and the how to videos made it simple! Thanks
Susan H - November 12, 2020

Right part, wrong problem
The part got here quickly but apparently it was not the problem. Hot water goes in to the hot inlet valve & still hot when it comes out in the hose but no hot water gets to the tub! If anyone knows how to fix this, please tell me.
Model Cross Reference
This part works with the following models:
PartSelect Number: PS3527427
Manufacturer Part Number: 5220FR2006H
Manufacturer Part Number: 5220FR2006H
Brand
Model Number
Description
