Gearcase 3360629 | Official Whirlpool Part | Fast Shipping | PartSelect
Gearcase – Part Number: 3360629
Gearcase – Part Number: 3360629 Gearcase – Part Number: 3360629 https://partselectcom.azureedge.net/Schematics/Maytag/FITJMEDJ.gif

Gearcase

Product Description

Gearcase Specifications

This is used in your direct drive washer that has a neutral drain.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Pumps but will not spin | Will not agitate | Noisy

This part works with the following products:

Washer, Washer Dryer Combo.

This part works with the following brands:

Whirlpool, Kenmore, KitchenAid, Roper, Maytag, Estate, Inglis, Crosley, Amana, Admiral, Magic Chef.

Part # 3360629 replaces these:

285312, 285362, 3349296, 3360629, 3360629R, 3360630, 388763, 389244, 389246, 3949609, 423, 62534, 62570, 62621, 62680, 63320, 63563, 63910, 8532118, 8546456... Show More
Questions and Answers
Ask our experts a question on this part and we'll respond as soon as we can.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Part Videos

Replacing your Whirlpool Washer Gearcase

Customer Repair Stories
Average Repair Rating: 2.1 / 5.0, 5 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Troy from Storm Lake, IA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Parts Used:
285753A, 3360629
Tub wouldn't turn, but motor would allow it to drain.
I took the two screws for the control panel out and tilted it up and back. Then remove the two metal clips which held the outer panel to the back panel. After disconnecting the power and water I tipped the washer on its back. I had to remove two clips to take the water pump off of the motor, then removed the two screws and clips which held in the motor. After removing the motor, I found the coupler was bad. To remove the gearcase, I took out the softener dispenser and removed one bolt to take out the agitator. Under the agitator was a clip. Three bolts held the gearcase to the frame. After removing them, the gearcase pulled straight out the bottom. Replacement was just a reverse process, with the addition of a light coat of grease to the gearcase shaft.
98 of 123 people found this instruction helpful.
Was this instruction helpful to you?
Francis from Ann Arbor, MI
Difficulty Level:
Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Parts Used:
3360629, 285785
Drum and agitator did not turn and machine squealed.
As best described in the clutch DIYs, removed the enclosure, unclipped the water pump, motor and elec. harness to check the coupling. The bushing separated from the plastic fingers which caused the squealing. Checked the gearbox and it turned for a limited amount before jamming. Ordered new gearcase and clutch (since it was over 10 yrs. old.), and a coupling. (Gearcase comes with half a coupling, so check if req'd for motor shaft.)
For ease of removing and re-installing the motor it is best the machine lays on its back. This way the grommets and coupling can be easily aligned on the face-plate without having to manually support the weight of the motor. In the tub, unsnap two agitator caps. The inner one has no tabs to break so pry and pull on the "ears". Use 7/16" socket wrench with extension to unscrew the bolt holding agitator to gear shaft end. Assuming the motor and face-plate are still off, unscrew the three screws holding the gearcase in place and slide it out. Before installing the new clutch onto the new gear shaft, slide the plastic thrust spacer? (in kit but not shown in any instructions) down the shaft, observing which is the correct side. Check for correct clutch spring, as per instructions. Slide clutch, open side up, down the shaft. Instal wire retainer (this can be tricky) and circlip. if the brake assembly slid down while sliding out the gear shaft, squeeze its spring with a pipe wrench and push it back up (with rubber mallet). The clutch kit comes with a plastic pawl? which mounts under the brake and mates with the clutch. If the locating pins for the old part are broken off, drill them out of their holes so the new part fits snug. Insert the gear shaft up the brake sleeve into the agitator so their splines mate. Screw gear case to its mounts, agitator to shaft end (not too tight here) and snap on caps. Screw on face-plate, replace coupling on motor shaft (if req'd.), set motor on face-plate, aligning the coupling and checking the grommets fit in their holes. Instal motor holding clips (with screws), mount water pump with its holding clips, and wire harnesses. Stand up machine and replace enclosure, back panel and hoses.
Replacing the gearcase was easy. Because of space limitations, removing and replacing the enclosure, etc. was a b**** that took most of my time. And watch the lid doesn't fall on your fingers!
73 of 260 people found this instruction helpful.
Was this instruction helpful to you?
david from Monroe, MI
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Parts Used:
3360629
The washer wouldn't spin or agitate.
Frist I disconnected the water lines and power cord. Then I leaned the washer back against the wall. Removed the 2 pump retainers and then the pump. Next removed the 2 screws from the motor retainers and pulled off the retainers and motor. Then removed the 3 bolts from the Gear case. Then removed the cap from the top of the agitator with a flat screw driver. Then removed the bolt from the top of the gear shaft. and removed the auger and agitator assembly. Then removed the gear case from the washer. Next removed the slip ring and then the clutch from the top of the gear case. Next removed the 1/4" screws from cover of gear case and removed the cover. Found the top gear bad. Ordered the new gear and pinion kit. Couldn't find any part #'s to match what PartSelect had. Ordered the gear that they should that fit most washers. The pics they had up looked the same as the one that was bad. Had the new gear in 3 days put it back together and it still wouldn't work right. Took it apart again and looked at it and found a small clip on the bottom side of the gear was upside down. Fliped it over put the gear back in and ran the washer with the gear case out and it worked. Put it back together again. And learned a good lesson always watch how you take things apart for when it's time to put it back together!
43 of 46 people found this instruction helpful.
Was this instruction helpful to you?
John from Upper Montclair, NJ
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Wrench (Adjustable), Wrench set
Parts Used:
3360629, 285811
Some of the teeth on the gears within the gear case stripped. And also, some of the agitator clutch parts were warped (they were plastic).
I'm not the one who actually did the repair, so I can't give you a blow-by-blow description. But my friend did the actual repair (I found and ordered the parts from your web site).

There was one almost insurmountable problem, however. The three-pin cog that connects the new gear case to the rest of the washing machine was changed.......the cross-section of each of the cogs was not round.....but teardrop shaped. I ordered the correct gear case, based upon the model number of the machine, but apparently somewhere down the years Whilrlpool must have changed the cog profile design.

So, the man who did the repair simply got out a metal mill file and filed down each of the cogs so that they were round. It wasn't perfect, but it worked.
41 of 49 people found this instruction helpful.
Was this instruction helpful to you?
Aaron from Lake Mills, WI
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Socket set
Parts Used:
3360629
The spin gear was striped.
I had to take the motor and transmission out. They are one piece. Removed the clutch, take off trans. cover, remove a snap ring, take the striped gear off, and put the new one on. Then put put everything back on the way it came off.
17 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
6 Reviews
4.7
out of 5
Filter By Rating:
  • 5 Stars
    5
  • 4 Stars
    0
  • 3 Stars
    1
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS341974
Manufacturer Part Number: 3360629
Brand
Model Number
Description
Kenmore
106.82872600
Washer - Kenmore Washing Machine Model 106.82872600 (10682872600, 106 82872600) Parts
Kenmore
110.1050299
Washer - Kenmore Washing Machine Model 110.1050299 (1101050299, 110 1050299) Parts
Kenmore
110.2071299
Washer - Kenmore Washing Machine Model 110.2071299 (1102071299, 110 2071299) Parts
Kenmore
110.2086299
Washer - Kenmore Washing Machine Model 110.2086299 (1102086299, 110 2086299) Parts
Kenmore
110.2087299
Washer - Kenmore Washing Machine Model 110.2087299 (1102087299, 110 2087299) Parts
Kenmore
110.2371220
Washer - Kenmore Washing Machine Model 110.2371220 (1102371220, 110 2371220) Parts
Kenmore
110.26058590
Washer - Kenmore Washing Machine Model 110.26058590 (11026058590, 110 26058590) Parts
Kenmore
110.2690290
Washer - Kenmore Washing Machine Model 110.2690290 (1102690290, 110 2690290) Parts
Kenmore
110.26902962
Washer - Kenmore Washing Machine Model 110.26902962 (11026902962, 110 26902962) Parts
Kenmore
110.2882790
Washer - Kenmore Washing Machine Model 110.2882790 (1102882790, 110 2882790) Parts
Kenmore
110.29601690
Washer - Kenmore Washing Machine Model 110.29601690 (11029601690, 110 29601690) Parts
Kenmore
110.29802891
Washer - Kenmore Washing Machine Model 110.29802891 (11029802891, 110 29802891) Parts
Kenmore
110.828918100
Washer - Kenmore Washing Machine Model 110.828918100 (110828918100, 110 828918100) Parts
Kenmore
110.828918110
Washer - Kenmore Washing Machine Model 110.828918110 (110828918110, 110 828918110) Parts
Kenmore
110.828918120
Washer - Kenmore Washing Machine Model 110.828918120 (110828918120, 110 828918120) Parts
Kenmore
110.828918130
Washer - Kenmore Washing Machine Model 110.828918130 (110828918130, 110 828918130) Parts
Kenmore
110.92093320
Washer - Kenmore Washing Machine Model 110.92093320 (11092093320, 110 92093320) Parts
Kenmore
110.92093720
Washer - Kenmore Washing Machine Model 110.92093720 (11092093720, 110 92093720) Parts
Kenmore
110.92293510
Washer - Kenmore Washing Machine Model 110.92293510 (11092293510, 110 92293510) Parts
Kenmore
110.92570200
Washer - Kenmore Washing Machine Model 110.92570200 (11092570200, 110 92570200) Parts
Kenmore
110.9281100
Washer - Kenmore Washing Machine Model 110.9281100 (1109281100, 110 9281100) Parts
Kenmore
110.98762790
Washer Dryer Combo - Kenmore Washer/Dryer Combo Model 110.98762790 (11098762790, 110 98762790) Parts
Kenmore
110.9975820
Washer Dryer Combo - Kenmore Washer/Dryer Combo Model 110.9975820 (1109975820, 110 9975820) Parts
Kenmore
110088732791
Washer Dryer Combo
Kenmore
11010202000
Washer
Kenmore
11010202001
Washer
Kenmore
11010502990
Washer
Kenmore
11010502991
Washer
Kenmore
11010852990
Washer
Kenmore
11010852991
Washer