Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11010502991

11010502991 Kenmore Washer - Overview

Get Parts and Repair Help for 11010502991

If you know the washer repair part you need, you can browse the list of all parts on the 11010502991, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 11010502991 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.80

Agitator Directional Cogs

Agitator directional cogs, otherwise known as dog ears, come in a package of four and are generally found in washers where the motor is connected directly to the washer. The agitat...

Order within the next 6 hrs and your part ships today!
$11.77

Direct Drive Motor Coupling

The direct drive motor coupling, also known as a coupling kit, is a newer version of the part and is used in your washer. The piece includes new metal sleeves that have been added in order to strengthen the part. This part works between the transmission and the motor; it is only used on direct drive washers with no belt. In order to replace this part, you will need a flat blade screw driver, a quarter inch nut driver, and a Phillips screw driver. Before making this repair remember to disconnect the power supply, and both fill hoses.

Order within the next 6 hrs and your part ships today!
$2.84

Suspension Spring

The suspension is meant to support the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down, or perhaps has stretched ou...

Order within the next 6 hrs and your part ships today!
$28.33

Direct Drive Water Pump

This direct drive water pump, also known as washing machine drain pump or washer drain pump, is manufactured for washing machines that do not have belts. This is a genuine Whirlpool part with two ports for water to pass through, a large one and a smaller one, that will need replacing if the washer has a defective pump. Tools needed are slip joint pliers, a flat blade screw driver, and a putty knife. Sandpaper might also be needed to remove rust from internal parts to install the new pump. The washer will have to be disconnected from power and tilted on its back.

Order within the next 6 hrs and your part ships today!
$44.29

Clutch Assembly

A clutch assembly is found in your washing machine and is responsible for spinning the basket during the spin cycle. A worn-down clutch can lead to a slower spin which can lead to ...

Order within the next 6 hrs and your part ships today!
$27.50

Lid Switch

This is a lid switch for a washing machine. The pin on the lid pushes on the lever of the lid switch to tell the washing machine that the lid is closed, which allows the wash cycle to begin. The washer will not spin if the machine senses the lid is open. The tools youll need for this repair are a Phillips screwdriver and 5/16 nut driver. Be sure to disconnect the power supply and fill hoses from the appliance. When reinstalling the harness, take notice of the flat edges on the plastic terminal; they should face towards the front of the washer. This is a genuine OEM part.

Order within the next 6 hrs and your part ships today!
$30.63

Water Inlet Valve with Mounting Bracket

The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-color...

Order within the next 6 hrs and your part ships today!
$3.56

Tub Spring

This tub spring is also known as suspension spring, balance spring, or counterweight spring. It is sold individually. The function of the part is to counterbalance the weight of the motor on the front of the front-load washer so the washer tub sits straight and even during the spin cycle. You may need to replace the spring if tub is sitting tilted forward. A broken spring will result in the tub being off-balance during the spin cycle which can cause further damage to washer parts. It is recommended to check all suspension springs as they often wear at the same rate. Tools needed for repair are a Phillips screw driver, flat blade screw driver, and a pair of pliers.

Order within the next 6 hrs and your part ships today!
$3.64

Thrust Spacer

This is a genuine OEM thrust spacer for your washer, and is also commonly known as a retainer ring. The spacer is about 2.5 inches in diameter, is made of plastic, and is white in ...

Order within the next 6 hrs and your part ships today!
$4.63

Screw & Washer (5/16-24 x 1)

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

Order within the next 6 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer stopped mid cycle

  • Customer: Travis from Pearland, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 948 of 971 people found this instruction helpful
1. Unplug washer.
2. Remove screws at control panel end caps.
3. Flip control panel back to expose wiring.
4. Detach lid switch wiring harness from control panel.
5. Use screwdriver to pry the 2 brass clips holding the back panel of the washer to the front and sides piece.
6. Tilt the front/sides piece over to expose lid switch.
read more

No movement from Basket & agitator

  • Customer: Jeff from Wayne, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 936 of 993 people found this instruction helpful
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor co... read more

Replace Water Pump Coupling

  • Customer: RICHARD from PHILA, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 774 of 827 people found this instruction helpful
Removed casing tip over washer disconnected water pump. Disconnected motor then replace coupling then reassemble motor then replaced water pump. read more