Models > 11014202300

11014202300 Kenmore Washer - Overview

Sections of the 11014202300

[Viewing 9 of 9]
Keep searches simple, eg. "belt" or "pump".
Direct Drive Motor Coupling – Part Number: 285753A
Direct Drive Motor Coupling
★★★★★
★★★★★
(158)
PartSelect #: PS1485646
Manufacturer #: 285753A
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft....
$27.04
  In Stock
Direct Drive Water Pump – Part Number: WP3363394
Direct Drive Water Pump
★★★★★
★★★★★
(93)
PartSelect #: PS11741239
Manufacturer #: WP3363394
The direct drive drain pump (Whirlpool Direct Drive Washer Pump, Drain Pump, Washer Drain Pump, Water Pump) removes water from the washer during the drain cycle without the use of a belt. The pump is ...
$56.18
  In Stock
Suspension Spring – Part Number: WP63907
Suspension Spring
★★★★★
★★★★★
(26)
PartSelect #: PS11743345
Manufacturer #: WP63907
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down or has stretched out and lost its spring, it could c...
$4.80
  In Stock
Lid Switch – Part Number: 3949247V
Lid Switch
★★★★★
★★★★★
(78)
PartSelect #: PS11722098
Manufacturer #: 3949247V
This switch (Lid Switch Assembly With Leads, Washer Lid Switch, Lid Switch Assembly, Washer Lid Switch) tells the washing machine that the lid is closed, which allows the wash cycle to begin. The lid ...
$46.73
  In Stock
Water Inlet Valve with Mounting Bracket – Part Number: 285805
Water Inlet Valve with Mounting Bracket
★★★★★
★★★★★
(127)
PartSelect #: PS334646
Manufacturer #: 285805
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There...
$38.76
  In Stock
Clutch Assembly – Part Number: 285785
Clutch Assembly
★★★★★
★★★★★
(68)
PartSelect #: PS334641
Manufacturer #: 285785
A clutch assembly (Clutch, Washer Clutch) is found in your washing machine and is responsible for spinning the basket during the spin cycle. The clutch lining can wear over time. If the clutch lining ...
$48.49
  In Stock
Agitator Bolt – Part Number: WP358237
Agitator Bolt
★★★★★
★★★★★
(9)
PartSelect #: PS11741866
Manufacturer #: WP358237
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
$7.48
  In Stock
Tub Spring – Part Number: WPW10250667
Tub Spring
★★★★★
★★★★★
(16)
PartSelect #: PS11751118
Manufacturer #: WPW10250667
This tub spring is also known as suspension spring, balance spring, or counterweight spring. It is sold individually. The function of the part is to counterbalance the weight of the motor on the front...
$7.48
  In Stock
Screw, 8/18 x 3/8 – Part Number: WP90767
Screw, 8/18 x 3/8
★★★★★
★★★★★
(2)
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$7.76
  In Stock
Tub Wear Pads - Package of 3 – Part Number: 285744
Tub Wear Pads - Package of 3
★★★★★
★★★★★
(8)
PartSelect #: PS334620
Manufacturer #: 285744
This package of pads contains three tub wear pads.
$15.50
  In Stock
Hose Clamp – Part Number: WP596669
Hose Clamp
★★★★★
★★★★★
(1)
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$7.76
  In Stock
Foot, Front - Single – Part Number: WPW10001130
Foot, Front - Single
★★★★★
★★★★★
(2)
PartSelect #: PS11747965
Manufacturer #: WPW10001130
The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is imp...
$7.48
  In Stock

Questions And Answers for 11014202300

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

1 question answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Carl
    August 4, 2021
    My washer spun but clothes were still damp and now switch does not activate to wash, would this be a switch problem or something else, what should i check? Water does run into the machine but it won't engage to wash or rince or anything. Help, clothes piling up.Thank you.
    For model number 11014202300
    Hello Carl, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is Water Level Pressure Switch PartSelect Number PS3408138. First open the control panel, and check the plastic tube coming from the water level valve. It may be clogged or corroded which means it should be changed out.

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Related Parts:

      Common Symptoms of the 11014202300

      [Viewing 20 of 20]
      Leaking
      Fixed by
      these parts
      Show All
      Pumps but will not spin
      Fixed by
      these parts
      Show All
      Will not agitate
      Fixed by
      these parts
      Show All
      Shakes and moves
      Fixed by
      these parts
      Show All
      Will not drain
      Fixed by
      these parts
      Show All
      Noisy
      Fixed by
      these parts
      Show All
      Spins slowly
      Fixed by
      these parts
      Show All
      Will not stop filling with water
      Fixed by
      these parts
      Show All
      No hot or cold water
      Fixed by
      these parts
      Show All
      Will Not Start
      Fixed by
      these parts
      Show All
      Timer will not advance
      Fixed by
      these parts
      Show All
      Will not fill with water
      Fixed by
      these parts
      Show All
      Burning smell
      Fixed by
      these parts
      Show All
      Leaks water
      Fixed by
      these parts
      Show All
      Fills and drains at the same time
      Fixed by
      these parts
      Show All
      Lid or door will not open
      Fixed by
      these parts
      Show All
      Touchpad does not respond
      Fixed by
      these parts
      Show All
      Lid or door won’t close
      Fixed by
      these parts
      Show All
      Not draining
      Fixed by
      these parts
      Show All
      Marks left on clothes
      Fixed by
      these parts
      Show All
      Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
      No movement from Basket & agitator
      The job looked intimidating but turned out to be very easy.
      First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
      The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
      One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
      Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
      Parts Used:
      Direct Drive Motor Coupling
      • Jeff from Wayne, NJ
      • Difficulty Level:
        Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Pliers, Screw drivers, Socket set
      1044 of 1108 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Washer stopped mid cycle
      1. Unplug washer.
      2. Remove screws at control panel end caps.
      3. Flip control panel back to expose wiring.
      4. Detach lid switch wiring harness from control panel.
      5. Use screwdriver to pry the 2 brass clips holding the back panel of the washer to the front and sides piece.
      6. Tilt the front/sides piece over to expose lid switch.
      7. Use nutdriver to detach ground wire.
      8. Use screwdriver to remove 2 screws holding lid switch in place.
      9. Install new lid switch. Make sure wiring harness piece is facing the right direction.
      10. Put washer back together in same order it was disassembled. Make sure front/sides piece connects to the clips at the bottom.
      Parts Used:
      Lid Switch
      • Travis from Pearland, TX
      • Difficulty Level:
        Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Screw drivers
      1014 of 1038 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      The lid switch had broken on my washing machine; the machine would not run.
      First I unplugged the washing machine. Then I removed the two screws that hold the top console in place; these are located in back of the main console (where the dials are). Once removed, the entire console swivels back, exposing the wires underneath. I unplugged the wiring harness that was connected to the washing machine top flat surface. I then removed the two s-shaped brackets with a screwdriver by prying underneath. This allowed me to remove the main sheet metal frame around the washing machine. The lid switch assembly is located under the top console. I simply removed it and replaced with the new assembly and put it back together. A snap!
      Parts Used:
      Lid Switch
      • Dennis from Evans City, PA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Screw drivers, Socket set
      574 of 600 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!