Frigidaire/Frigidaire_Thumb/DJH3SCBD.gif
See part F37 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Temperature Sensor

★★★★★
★★★★★
4 Reviews
$ 27.35   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11758156
Manufacturer Part Number 5304504897
Manufactured by Frigidaire
Troubleshooting
This part fixes the following symptoms:
Oven is too hot | Oven not heating evenly | Little to no heat when baking | Element will not heat
This part works with the following products:
Range, Wall Oven, Microwave Oven Combo, Microwave.
This part works with the following products:
Frigidaire, Kenmore, Electrolux, Uni.
Part# 5304504897 replaces these:
AP6025829, 318562500
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

14 questions answered by our experts.
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Cyndy
August 22, 2019
Oven only heats to about 150 when using roast or bake i can see the glow from heat source (it is a gas range) but will not heat up. I can turn on broil and it heats up but can’t control temperature
For model number FPGH3077RFB
Hi Cyndy, Thank you for your question. Thank you for your question. If the oven is not heating correctly, then the issue is likely with the oven sensor, sometimes called the oven thermostat, and you will need to check it with a multimeter. When testing the sensor with a multimeter, the sensor should be tested at room temperature and it should be unplugged from the oven. You will need to measure the resistance between the two prongs at the end of the sensor connector. Replace the oven sensor if the reading is less than 900 Ohms or more than 1200 Ohms. I hope this helps. Thank you and have a great day! I hope this helps. Thank you and have a great day!

7 people found this helpful.

Was this helpful?
Thank you for voting!
Sandra
November 27, 2017
I have tried all your % of problem parts on your website to get my oven to get hot, and nothing has helped, could this part below help? Any suggestions?
For model number FGES3045KFE
Hi Sandra, Thank you for the question. If both elements in the oven are not working at all, I suggest replacing the Control Board,Part Number: PS2368652. If the elements turn on but are not getting hot enough, then replacing the sensor should fix the issue. Hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Bee
November 19, 2018
F10 is displayed when oven warms up.. is it the sensor
For model number 79040292410
Hello Bee, Thank you for the question. The F10 fault code on your Kenmore oven indicates that the oven has overheated and the most common part replaced is the Temperature Sensor, PartSelect Number: PS11758156. If the sensor did not fix the issue, you may need to replace the control board, Part Number: PS11757779. Thank you for your inquiry, good luck with this repair!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Karen
February 12, 2018
This part at sears is 147.03 dollars. Do you think it is the same part?
For model number 79097313412
Hi Karen, Thank you for the question. Yes, this is the same part. We may order a bigger stock in so we get a better discount on the item, this reflects in the savings we pass onto our customers! Hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Loal
February 20, 2019
Hi, my wife ran the self clean on our double wall oven, did one then the other right after, the next day the lower did not work and the upper did , i shut off the breaker and pulled out and made sure the thermal switch was good, looked good, when i powered up it switched the lower worked and the upper did not, would it be the circuit board? Sounds electrical, any idea
For model number Kenmore ,fget3065pfd
Hello Loal, Thank you for contacting us. There are a few parts that could cause this issue in your appliance. First I would say test your elements with a multi meter to see if they are working correctly or not. They should be reading between 0 - 50 ohms to be working correctly. The other part you should check would be your oven temperature sensor. That can also be tested with a multi meter and should be reading between 1000 - 1100 ohms. If those three parts are fine however, then the issue may be in your control board. I hope that helps. Good luck with your repair

2 people found this helpful.

Was this helpful?
Thank you for voting!
Dale
July 31, 2019
On my Electrolux wall unit, must i replace the temperature sensor from the back side of the unit or can i replace it from the front, by reaching into the oven compartment?
For model number EW30EW55GS7
Hi Dale, thank you for your question. There are two ways to do the installation. From the front: https://www.youtube.com/watch?v=hFZlbgMNZAc. And from the back: https://www.youtube.com/watch?v=yTDerTiSW4Y. I hope that helps. Good luck with your repair.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Amy
December 17, 2018
My oven takes a long time to light. Sometimes it does, and it gets up to temperature, but is slow in doing so. Sometimes it doesn't get up to temperature at all. The broiler works fine, but the bake and convection settings do this. Usually if i go through the preheat button, it heats up but it is slow. Do you think i need the temperature sensor or the ignitor? Would a failing ignitor work sometimes and not all the time?
Hi Amy, Thank you for your question. If the oven is not heating correctly, then the issue is likely with the oven sensor, sometimes called the oven thermostat, and you will need to check it with a multimeter. When testing the sensor with a multimeter, the sensor should be tested at room temperature and it should be unplugged from the oven. You will need to measure the resistance between the two prongs at the end of the sensor connector. Replace the oven sensor if the reading is less than 900 Ohms or more than 1200 Ohms. I hope this helps. Thank you and have a great day!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Karen
February 12, 2018
Can you explain to me how to teh temperature sensor probe. Do i test it from inside the oven or somehow through the back?
Hi Karen, Thank you for your question. If the oven is not heating correctly, then the issue is likely with the oven sensor, sometimes called the oven thermostat, and you will need to check with a multimeter. An oven thermostat is a switch that opens and closes in response to the temperature it senses. It is typically found in the control panel, where a liquid-filled temperature-sensing bulb senses and maintains the internal oven temperature by cycling heat on and off. Before repairs or testing can begin you must disconnect the electricity at the fuse panel, at the circuit breaker panel, or by pulling the plug. Make sure the power is off before proceeding. A jolt from 220 volts can be fatal, use caution! Access the oven thermostat, which is located in different places depending on the make and model: On freestanding ranges, access the thermostat by removing the screws that hold the back panel in place at both ends. On models with front-loading controls, remove the panel and tilt it for access. Be careful not to let the wires disconnect from their components. Some built-in models have a removable backsplash. Lift the backsplash, rest it on the cook top and remove the screws from the backsplash, which holds the rear panel. On wall ovens or eye-level ranges, access the control panel by opening the door and removing the screws that secure it. The screws may be under the exhaust hood or below the control panel. If the control panel is hinged, simply tilt it towards you. On some models both the rear and front control panels must be removed. The screws may be found on the trim and occasionally the trim must be removed. When testing the thermostat switch contacts for continuity, refer to the wiring diagram and remove only those wires being tested - and only one pair at a time. Test switch contact terminals as per your wiring diagram. If the switch lacks continuity at any of the contact terminal points then the entire thermostat switch needs to be replaced. Adjusting the thermostat: Test the oven temperature by placing the tester in the oven's center and leaving it for 30 minutes at 350 degrees. Record the minimum and maximum temperatures of three cycles, then add those figures together, divide the result by six and you have the oven's average temperature. If the average temperature is more than 25 degrees off, try calibrating the thermostat by following your appliance manual instructions for thermostat calibration. Normally, thermostats are calibrated by pulling the oven's thermostat knob off, turning the knob over and adjusting the calibration ring on the back. If your oven doesn't have a calibration ring you may need to replace the thermostat. To remove the thermostat: Disconnect the capillary tube and push it through the back oven wall, being careful not to break the flammable capillary tube wire. Remove the screws that secure the thermostat to the control panel and gently pull the thermostat out, leaving the wires in place. To install a new thermostat, reverse the disassembly procedures (Step 7 above), transferring the wires individually from the old unit to the new. I hope this helps. Thank you and have a great day!

Was this helpful?
Thank you for voting!
Dale
July 31, 2019
I encountered an f10 code error (beeping too) during the end of the self-clean cycle. I shut off the breaker to the oven for several minutes. I then turned the breaker back on which cleared the code error and beeping. I turned the oven on and set and started the oven for a baking cycle at 350 degrees - it would not heat up (oven cavity cold to the touch).Will the temperature sensor correct this problem?
For model number EW30EW55GS7
Hi Dale, thank you for your question. There are a few parts that could cause this issue in your appliance. First I would say test your elements with a multi meter to see if they are working correctly or not. They should be reading between 0 - 50 ohms to be working correctly. The other part you should check would be your oven temperature sensor. That can also be tested with a multi meter and should be reading between 1000 - 1100 ohms. If those three parts are fine however, then the issue may be in your control board. I hope that helps. Good luck with your repair.

Was this helpful?
Thank you for voting!
Lori
March 26, 2019
A paper plate went on fire in my Frigidaire microwave, i have no display.I was told that it was probably a temperature sensor. do you agree? and what is involved to replace? thank you , lori
For model number Fgmv175qfa
Hi Lori, Thank you for your question. Most paper plates can be used in the microwave as long as they are microwave safe. You should consult your manual to verify the types of paper plates that you can use and when you buy paper plates check the packaging to see if they are microwave safe. If the display is not working, you will check the touchpad, the electronic control board, the wiring connections between them, the door switches and the fuse. I hope this helps. Thank you and have a great day!

Was this helpful?
Thank you for voting!
Customer Repair Stories
 Average Repair Rating: 4.5 / 5.0, 2 reviews. What's this?
    Sort by:
    Sorry, we couldn't find any existing installation instruction that matched.
    Both oven bake and broil elements lost power suddenly at the same time.
    Installation of the temparature sensor, one of the technician recommended parts took no time, just two screws and a snap off/snap on part. It did not fix the problem. I then replaced the main control panel, which requires more work, but didn't solce the ussue either. I then replaced the thermal fuse, which wasn't mentioned by tech support, and required much more disassebly of the top panels of the stove, with still no fix to the problem. I am waiting to replace the thermostat heat sensor unit, the only other part in the circuit controlling power supply, requiring removal of the stove top again,
    • Alexander from DELMAR, NY
    • Difficulty Level:
      Really Easy
    • Total Repair Time:
      30 - 60 mins
    • Tools:
    • Parts Used:
      5304504897
    4 of 5 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Top oven overheating
    Have a double wall oven and the top oven would not shut off or broiler part would stay on and burn tops of food. Since bottom oven was not having any issues felt like it could
    Not be control panel so decided to try the temp sensor. Since replacing oven has worked properly.
    • Ronald from NEVADA, MO
    • Difficulty Level:
      Very Easy
    • Total Repair Time:
      Less than 15 mins
    • Tools:
      Screw drivers
    • Parts Used:
      5304504897
    1 person found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      4 Reviews
      5.0
      Filter By Rating:
      • 5 Stars
        4
      • 4 Stars
        0
      • 3 Stars
        0
      • 2 Stars
        0
      • 1 Star
        0
        Sort by:
        Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
          Model Cross Reference
          This part works with the following models:
          PartSelect Number: PS11758156
          Manufacturer Part Number: 5304504897
          Brand
          Model Number
          Description
          Kenmore
          79030522802
          Wall Oven - WALL OVEN
          Kenmore
          79030529802
          Wall Oven - WALL OVEN
          Kenmore
          79030552803
          Wall Oven - GAS WALLOVEN
          Kenmore
          79030553801
          Wall Oven - GAS WALLOVEN
          Kenmore
          79030553803
          Wall Oven - GAS WALLOVEN
          Kenmore
          79030554803
          Wall Oven - GAS WALLOVEN
          Kenmore
          79030559803
          Wall Oven - GAS WALLOVEN
          Kenmore
          79031032804
          Range
          Kenmore
          79031033803
          Range
          Kenmore
          79031033804
          Range
          Kenmore
          79031039804
          Range
          Kenmore
          79031042803
          Range
          Kenmore
          79031042805
          Range
          Kenmore
          79031043805
          Range
          Kenmore
          79031049805
          Range
          Kenmore
          79031053000
          Range
          Kenmore
          79031062100
          Range
          Kenmore
          79031063100
          Range
          Kenmore
          79031069100
          Range
          Kenmore
          79031073100
          Range
          Kenmore
          79032602310
          Range - GAS RANGE
          Kenmore
          79032602311
          Range - GAS RANGE
          Kenmore
          79032602312
          Range - GAS RANGE
          Kenmore
          79032602313
          Range - GAS RANGE
          Kenmore
          79032602314
          Range - GAS RANGE
          Kenmore
          79032602315
          Range - GAS RANGE
          Kenmore
          79032602316
          Range - GAS RANGE
          Kenmore
          79032602317
          Range - GAS RANGE
          Kenmore
          79032603310
          Range - GAS RANGE
          Kenmore
          79032603312
          Range - GAS RANGE

          Get in touch, we're here to help!

          Open until 10PM EST

          Contact Customer Service