Quick Question!

Have you ever purchased from PartSelect.com before?

11741149-1-S-Whirlpool-WP33313541-Tumbler Seal
11741149-1-S-Whirlpool-WP33313541-Tumbler Seal 11741149-2-S-Whirlpool-WP33313541-Tumbler Seal 11741149-3-S-Whirlpool-WP33313541-Tumbler Seal https://partselectcom.azureedge.net/Schematics/Maytag/36054.gif

Tumbler Seal

Your Price

Order within the next 11 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11741149
Manufacturer Part Number WP33313541
Manufactured by Whirlpool

The tumbler seal can be used for the front or rear. Sold individually.

This part works with the following brands: Maytag.

This part works with the following products: Dryer, Washer Dryer Combo.

This part fixes the following symptoms:

  • Noisy.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.3 / 5.0, 2 reviews What's this?
1-2 of 2

27 of 33 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers
Customer: Jim from Los Angeles, CA

Drum rubbing metal to metal on front support

1. Unplugged dryer, removed front (2 phillips screws near bottom) set aside with wires attached
2. Removed front support (4 hex head screws)
3. Drilled out pop-rivets, discarded old glides (why didn't Maytag use rollers?)
4. Riveted new glides in place.
5. (Oops!) trimmed cork pads, smeared with glue, shoved under glides, held down until firm
6. Removed drum (pushed belt back to groove, pulled drum off rollers, lifted belt off drum, worked drum out) Left belt on pulley and tension wheel as pattern when I replace it.
7. Scraped old gasket felt off back chassis and front support
8a. Folded gasket lengthwise and glued into front support channel with fold on outside diameter. It was too short.
8b. (Oops! Why didn't this come with instructions?) Pulled it out, reversed it and replaced it with fold to inside diameter. It fit. Glued ends together.
9. Glued other felt gasket into back chassis. (Good ventilation needed here!)
10. Replaced rollers. (This did have instructions, despite being easy. I didn't use any grease. Experience as a locksmith says don't lube anything that isn't sealed from dust. I also vacuumed out 15 years of dust.)
11. Replaced belt. (The old one looked fine, but I was advised to do the belt and rollers along with the glides.) The grooves touch the drive pulley, the flat goes around the tensioner, and the belt exiting to the left seems like it will rub the pulley, but it doesn't once the drum is installed.
12. Turn the drum around (Nice, it's symmetrical!) and work it back in.
13. Lift the belt around the drum edge (I used bull clips to hold it in place.)
14. Check the belt on the pulleys, move the drum in more, take off clips, move the belt to the groove.
15. put the drum on the rollers, lift the belt out of the groove, and spin the drum a little while watching the pulleys to check it.
16. Screw the front support back in place.
17. Screwed the front on and plugged it in.
It works!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

12 of 13 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers
Customer: Kerry from South Ozone Park, NY

Scraping sounds from drum; dirt marks and ripps on clothes.

Removed top screws and the front cover.
Removed lint filter harness/air vent assembly (two screws inside dryer tumbler, 6-7 screws along vent assembly).
Removed front dryer tumbler sealer panel (2 screws on each side).
Scraped off old felt sealer with screwdriver.
Drilled out remnants of old rivets.
Replaced gliders with cork underneath.
Riveted gliders into position.
Used mighty putty to fill the cut metal around the top of the sealer panel (resulting from the dryer tumbler rubbing without proper gliders).
Glued new felt sealer around tumbler sealer panel.
Reassembled the entire unit in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-2 of 2

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11741149
Manufacturer Part Number: WP33313541
Brand Model Number Description
MaytagDE106Dryer - Electric
MaytagDE107Dryer - Electric
MaytagDE110Dryer - Electric
MaytagDE18CADryer - Electric
MaytagDE18CMDryer - Electric
MaytagDE18CSDryer - Electric
MaytagDE18CTDryer - Electric
MaytagDE19CADryer - Electric
MaytagDE19CDDryer - Electric
MaytagDE19CSDryer - Electric
MaytagDE19CTDryer - Electric
MaytagDE210Dryer - Electric
MaytagDE212Dryer - Residential
MaytagDE21CADryer - Electric
MaytagDE21CMDryer - Electric
MaytagDE21CSDryer - Electric
MaytagDE21CTDryer - Electric
MaytagDE22CADryer - Electric
MaytagDE22CSDryer - Electric
MaytagDE22CTDryer - Electric
MaytagDE23CDDryer - Electric
MaytagDE303Dryer - Residential
MaytagDE308Dryer - Electric
MaytagDE309Dryer - Electric
MaytagDE312Dryer - Residential
MaytagDE313Dryer - Residential
MaytagDE382Dryer - Electric
MaytagDE408Dryer - Electric
MaytagDE409Dryer - Residential
MaytagDE410Dryer - Residential