Electronic Control Board W10756692 | Official Whirlpool Part | Fast Shipping | PartSelect
Electronic Control Board – Part Number: W10756692
( Grid squares measure 1x1 inch )
Electronic Control Board – Part Number: W10756692 Electronic Control Board – Part Number: W10756692 Electronic Control Board – Part Number: W10756692 https://partselectcom.azureedge.net/Schematics/Maytag/OSFPJUUG.gif

Electronic Control Board

PartSelect Number PS10064572

Manufacturer Part Number W10756692

Manufactured by Whirlpool

Product Description

Electronic Control Board Specifications

This part helps with the tumble and spin cycle. If your motor won't run in either the wash or rinse cycle or if the fuse on the board is blown, then you have to replace this part. The fuse is not sold separately. NOTE: Motor is sold separately.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Pumps but will not spin | Will Not Start

This part works with the following products:

Washer.

This part works with the following brands:

Kenmore, Whirlpool, KitchenAid, Maytag.

Part # W10756692 replaces these:

8181693, 8181693R, 8182679, 8182705, 8182706, AP5956390.
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
6 questions answered by our experts.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer Repair Stories
Average Repair Rating: 3.6 / 5.0, 3 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bradley from Red Wing, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
W10756692
My washer would not always finsh the cycle (most of the time it would run between 2 and 30 minutes) and then the time display would flash and the washer would shut down and beep. An f06 fault code flashed in the display.
First I removed the screws and the plastic slide clips to remove the back plate. I then went to the lower right of the washer and found the motor control unit. It has about four plus going into it. The front inside mount of the control unit has a clip on it that must be pushed so you can pull the unit free of the bottom of the machine. Once the control unit was free I flipped open the plug cover with a screwdriver which just snaps over the plugs. I then removed the plugs from the unit carefully so I didn't break them. It was a tight work space and I had to pop out some of the clips that hold the wire harness in place to get some slack in the wires. I then pushed up on the washing drum which gave me enough room to slide to old unit out and get the new one in. Then just reconnect the plugs, plug cover, snap the unit back into place, refit and wire harness clips that where removed, and place the back panel of the machine back on. I tested mine before putting the back panel on and it completely solved the problem. Note that there are 2 control units in this machine 1. motor control and 2. the central control located behind the display. I was told it could have been either one of them, but after some research I chose the motor control unit since it seemed to be a problem with the tachometer sensor which is read through the motor control unit.
87 of 96 people found this instruction helpful.
Was this instruction helpful to you?
Christina from Englewood, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Parts Used:
W10756692
error F 11. Mashine would not run
removed screws on front control panel. found info sheet. read that this part was correct. replaced the motor control unit tho saw no damage on old unit and it works fine now.
26 of 35 people found this instruction helpful.
Was this instruction helpful to you?
Brent from Normandy Park, WA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Parts Used:
W10756692
Motor Control Board faulted.
I read the instructions once and then started. It was easy but did take an hour to do the entire job.
18 of 29 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
1 Review
5
out of 5
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS10064572
Manufacturer Part Number: W10756692
Brand
Model Number
Description
Kenmore
11042822200
Washer
Kenmore
11042822201
Washer
Kenmore
11042822202
Washer
Kenmore
11042822203
Washer
Kenmore
11042824200
Washer
Kenmore
11042824201
Washer
Kenmore
11042824202
Washer
Kenmore
11042824203
Washer
Kenmore
11042826200
Washer
Kenmore
11042826201
Washer
Kenmore
11042832200
Washer
Kenmore
11042832201
Washer - Kenmore Washing Machine
Kenmore
11042834200
Washer
Kenmore
11042834201
Washer
Kenmore
11042836200
Washer
Kenmore
11042836201
Washer
Kenmore
11042922200
Washer
Kenmore
11042922201
Washer
Kenmore
11042922202
Washer
Kenmore
11042922203
Washer
Kenmore
11042924200
Washer - Kenmore Washing Machine
Kenmore
11042924201
Washer
Kenmore
11042924202
Washer
Kenmore
11042924203
Washer
Kenmore
11042926200
Washer
Kenmore
11042926201
Washer
Kenmore
11042926202
Washer
Kenmore
11042926203
Washer
Kenmore
11042926220
Washer - WASHER
Kenmore
11042932200
Washer