Models > 11042824203

11042824203 Kenmore Washer - Overview

Sections of the 11042824203

[Viewing 7 of 7]

Manuals & Care Guides for 11042824203

Click to download
Keep searches simple, eg. "belt" or "pump".
Washer Door Bellow – Part Number: WP8182119
Washer Door Bellow
★★★★★
★★★★★
(31)
PartSelect #: PS11744957
Manufacturer #: WP8182119
$217.66
  In Stock
Order within the next 5 hrs and your part ships today!
Drain Pump Kit – Part Number: 280187
Drain Pump Kit
★★★★★
★★★★★
(53)
PartSelect #: PS1485610
Manufacturer #: 280187
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.
$156.79
  On Order
Door Lock Latch – Part Number: WP8182634
Door Lock Latch
★★★★★
★★★★★
(23)
PartSelect #: PS11745016
Manufacturer #: WP8182634
This part is used on front load washers and includes the interlock switch assembly.
$123.15
  In Stock
Order within the next 5 hrs and your part ships today!
Water Inlet Valve – Part Number: WP8181694
Water Inlet Valve
★★★★★
★★★★★
(27)
PartSelect #: PS11744913
Manufacturer #: WP8181694
Used with some front load washers. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
$76.27
  In Stock
Order within the next 5 hrs and your part ships today!
Shock Absorber – Part Number: WP8182703
Shock Absorber
★★★★★
★★★★★
(2)
PartSelect #: PS11745030
Manufacturer #: WP8182703
Shock absorbers help keep the washer from vigorous shaking during its cycles. Sold individually.
$59.79
  In Stock
Order within the next 5 hrs and your part ships today!
Screw – Part Number: WP488729
Screw
★★★★★
★★★★★
(1)
PartSelect #: PS11742721
Manufacturer #: WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
$7.76
  In Stock
Order within the next 5 hrs and your part ships today!
Door Hook/Strike – Part Number: WP8181651
Door Hook/Strike
★★★★★
★★★★★
(6)
PartSelect #: PS11744910
Manufacturer #: WP8181651
Attaches to door lock mechanism.
$15.88
  In Stock
Order within the next 5 hrs and your part ships today!
Bellow to Outer Tub Clamp – Part Number: WP8182210
Bellow to Outer Tub Clamp
★★★★★
★★★★★
(5)
PartSelect #: PS11744959
Manufacturer #: WP8182210
Used to help hold your bellow in place on your washer.
$35.88
  In Stock
Order within the next 5 hrs and your part ships today!
Hose Clamp – Part Number: WP285655
Hose Clamp
★★★★★
★★★★★
(2)
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$8.79
  In Stock
Order within the next 5 hrs and your part ships today!
Flowmeter – Part Number: WPW10110225
Flowmeter
★★★★★
★★★★★
(10)
PartSelect #: PS11748313
Manufacturer #: WPW10110225
This part continually measures the amount of water entering the tub. It will make adjustments if too much or too little water is present.
$98.89
  In Stock
Order within the next 5 hrs and your part ships today!
Bellow Clamp – Part Number: W10902779
Bellow Clamp
★★★★★
★★★★★
(7)
PartSelect #: PS11765855
Manufacturer #: W10902779
This is the replacement bellow clamp for your washer. It approximately 16 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place on t...
$31.44
  In Stock
Order within the next 5 hrs and your part ships today!
Baffle Set – Part Number: 285976
Baffle Set
★★★★★
★★★★★
(6)
PartSelect #: PS970109
Manufacturer #: 285976
This set includes the 3 baffles ONLY.The screws are sold separately.
$76.85
  In Stock
Order within the next 5 hrs and your part ships today!

Questions And Answers for 11042824203

Be the first to ask our experts a question about this model!

Common Symptoms of the 11042824203

[Viewing 17 of 17]
Leaking
Fixed by
these parts
Show All
Will not drain
Fixed by
these parts
Show All
Will not stop filling with water
Fixed by
these parts
Show All
Lid or door won’t close
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Shakes and moves
Fixed by
these parts
Show All
Noisy
Fixed by
these parts
Show All
Will not fill with water
Fixed by
these parts
Show All
Lid or door will not open
Fixed by
these parts
Show All
Pumps but will not spin
Fixed by
these parts
Show All
Will not agitate
Fixed by
these parts
Show All
Marks left on clothes
Fixed by
these parts
Show All
No hot or cold water
Fixed by
these parts
Show All
Burning smell
Fixed by
these parts
Show All
Spins slowly
Fixed by
these parts
Show All
Door latch failure
Fixed by
these parts
Show All
Timer will not advance
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bellows were moldy, needed to replace
The first step is to remove the retainer ring that holds the outside of the bellow in place.
To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will find a spring streached about 3" connected to a small diameter wire (1mm.) that runs all the way around the outside portion of the bellow.
Use a small screwdriver or other to pull and pry the spring away from the rubber bellow. Be careful not to damage the spring or ring. Once you have grip on it, pull it carefully toward you then up and off of the bellow.

The front portion of the bellow is now free and can be peeled off. Start at any point and pull the rubber bellow in toward the opening of the washer, it comes off easily.
When you get to the detergent outlet on the upper left side, grab the plastic tube and carefully pull the bellow from around it. There is no adhesive or clamp holding this in place, just friction. Remove the rest of the front portion of the bellow.
Push as much of the bellow into the washer as possible to get it out of the way.

Once this is off comes the slightly tricky part. Look up at the top right portion of the bellow that is still attached. You may need to feel with your hand but you should be able to see it. You are looking for the screw/nut end of a giant hose clamp. This hose clamp goes around the entire bellow and the secures it to the portion that holds the basket.
This is where the stubby screw driver comes in handy. There is not nearly enough room for a standard one and a nut driver or wratchet are too big. The nut will be pointing down and will need to be replaced the same way.
Loosen the hose clamp almost all of the way, not necessary to have the hose clamp come completely apart.
You can now remove the entire hose clamp from around the bellow by pulling it forward.
You will need to remove the hose clamp from the washer. To do this, squeeze it in from the sides about 6", don't kink it. Push it down toward the floor between the basket and the metal front panel. You will now be able to remove it from the top of the opening and be able to pull the bottom portion out.
Pull the old bellow completely out, very easy to do.

Time to install the new bellow. Figure out which side goes in and which faces out. The big hint is that the water inlet is on the upper left side.
You will notice at the top of the bellow on the portion that goes inside of the washer, you will find a small triangular shaped tab about 1/4" high. This is your centering mark. This will be at the very top. If you keep this at the top, everything will line up perfectly.

Slip the bellow over the edge of the portion that holds the basket where you removed the old one. I started at the top and worked left so I could install the detergent inlet tube. Pull this through the bellow carefully. It doesn't take a lot of force.
As you are pressing the bellow on this lip, you will notice that there is a 1/2" high back stop all of the way around. This is great because as you press it on, there is a positive stop and you can't go further than necessary. Continue to press it in all of the way around.

Now it is time to install the Hose clamp. Un bend anything that might have bent on the clamp. With the nut at the top or top right with the nut facing down to the floor while holding it vertically, squish it slightly inward, put the bottom portion in first then the top portion. Orient is as it was when you took it off. Slide it around the bellow. You will feel a positive stop.
Grab the stubby screwdriver and tighten down the hose clamp. I did about a medium force when tightening. It doesn't take a lot of force.

Now it is time to pull the remaining part of the bellow out of the basket and fit it into place. Press it around the outside portion of the opening so it hooks over the lip. This w
Parts Used:
Washer Door Bellow
  • Franck from Annandale, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
354 of 378 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not drain ,F02 and SUD code displaying
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the pump, using the water vac to catch the water as it leaked out.
(5) I removed the wiring to the motor.
(6) I removed the screw that holds the pump in place with a Torx T-20 socket.
(7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ).
(8) I tested the pump and found it would run but was making a lot of noise and running slow.
(9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4).
Don Kramer
Wichita, Kansas
Parts Used:
Drain Pump Kit
  • Donald from Wichita, KS
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Socket set
225 of 231 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
front load washer latch replacement
1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. reverse order to finish.
Parts Used:
Door Lock Latch
  • James from Vilonia, AR
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
190 of 222 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!