ZIR301NBRAII General Electric Refrigerator - Instructions

Unscrew the mounting screw and cut the tubes as close as you can to the valve. You cannot reuse the valve as the self sealing lock washers will be destroyed once you take out the tubes. Push the newly cut tubes into the new self sealing new valves and remount. Easy Peasy!

pullee refrigerator out to get to back un pluged power took off back cover unscrewed one screw to loosen water valve unscrew water inlet line ther are two water lines in back of water valve i cut them as close to water valve as i could push the water lines that i cut off into water valve makin sure in the rigfht place they are quick disquinect just push in and ther on screwed water valve back on connected water inlet line replaced back cover pluged in power pushed refrigerator back in and was done it had to run for a little while to get the air out then worked fine

turn water off to ice maker,unplugged refrigerator, took back panel off took old part off and put new part on

Just put on, part was great. Will buy parts again from this company.

Shut off water supply and unplugges refrigerator. Took of bottom panel on back of refrigerator. Discontected power plug and water lines from old water valve, removed water valve. Put in new water valve and reconnected water lines and power plug. Plugged refrigerator back in, turned on water supply and checked for leaks. Put cover back on. (It's also a good opportunity to clean out the dust and dirt under the fridge and around the motor and condensor)

I shut the water supply and took off the rear panel.
One screw released the valve. Pulled off water lines(3) and electrical connectors and installed all on new valve. Screwed the valve and the panel back and turned on the water supply. Prior instructions on website helped. Part came in two days. This part should have never failed. Looks like the housing is two parts glued together. Glue failed after 7 years. G.E. should cover this. My warranty expired after 5 years. M.K. Boca Raton,Fl.

Unplugged fridge, shut off water supply. Removed bottom back panel of the fridge and carefully vacuumed up all the dust. Located the water valve to the left of the compressor. It is attached to the side of the fridge by a metal bracket. Remove the screw from bracket and lift up on the whole assembly. Now I removed the electrical connectors and pushed in on the quick release tabs to pull out water lines. When installing water lines to new valve be sure to push them all the way in. The water lines are marked so you will know how far they must go in. Attached electrical connectors and remounted whole assembly back to the side of the refrigerator. Turned on water supply and plugged fridge back in. Checked water dispenser for proper operation and also checked water valve for leaks. Reattached the back cover to the fridge and that was it.

1)turn off water supply to appliance 2)disconnect appliance from power supply. 3)remove grill. 4)remove valve retaining fastener. 5)disconnect two wiring devices. 6) depress retaining devise at each water line to disconnect. note: if the lines do not releace, use utility knife to cut lines as close to unit as possible. 7)attach new valve in reverse order.

It was very simple. Pull the fridge back (unplug and turn off water), remove the cardboard backing and disconnect/unhook the current water valve and reverse the process to connect the new.

Followed instructions others posted. No need to cut any water lines, just push the white collar on the new valve, pull out line and do the same to install lines. Only issue was inlet line leaked after initial installation. It was leaking above the connection, so teflon tape wasn't the answer. Answer was to hold the line in exactly the routing place it was before removing.
It took a few days for ice machine to return to normal (as in making ice in quantity), but works like a champ now.

very simple repair.....push two hoses into compression fittings on the bottom, plug two wire harnesses into the back, and put a screw into the front to attach to the refridgerator frame. After that, just turn water back on and plug it in. Ran great.

Part also came in quicker than expected......which was a definate plus.

turn off water remove back cover remove 1 screw holding water valve use wrench to remove main water line input push up holders on bottom of selinoids pull both output lines loose disconnect two electrical plugs reinstall new valve in reverse order

Removed back panel. Cut the water lines and replaced the double outlet water valve. The only issue was the long period of time until the water flowed from the outlet. Be prepared to wait, it will take some time for the water to flow.

After confirming that a frozen water line was not my issue, I confidently bought this item and installed it within minutes after receiving it! It is easy to install - just close the connection to your refrigerator, open the rear lower panel, disconnect the water tubings and electrical connectors. Reverse that - you have the installation. Plug the refrigerator back on, turn the water back on for the refrigerator - and observe for any leaks. If no leaks - try dispensing water. Working great for me! My refrigerator's model is a GE, model # zfsb26dnass.

I was unplug the electrical,closed the water line.replaced old water outlet with the new one;and there work fine.Thanks