ZIR301NBRAII General Electric Refrigerator - Instructions

I went on Google to get GE Tech Manual. But really, undid screws for back plate; Dismounted (1 screw) Water Solenoid assembly; disconnected 3 water hoses into solenoid; unplug two power connectors. Then reversed the process with new Water Solenoid...works great!

Followed the instructions from your site and they were perfect. Unfortunatly that wasn't the problem. It still doesn't work.

per the video - took off panel, remove the existing part, and replaced.

Since the mechanisms were in the freezer icemaker area, we deduced it was the fan motor. Ordered that from your store and it was delivered to our door in two days. Great service.

The part was replaced and our refrigerator has been quiet for the first time since we moved in almost four years ago and the refrigerator was new.

I watched the video instruction and it was very easy to replace. took me less than 30 minutes.

After gaining access to the back of the refrigerator. I shut off the water valve and pulled the electrical power plug. I removed 6 screws from the access panel. I then removed 1 screw holding the water valve. I disconnected the electrical connectors. Disconnected the water inlet tubing with an adjustable wrench. I removed the water to the door and water to the ice maker by pushing in on the collar which released the tubing. I discarded the old valve and installed it in reverse order. Did not fix the problem. My next guess is the control module.

replaced double outlet water valve. Valve works as it should. Shipping was much quicker than I expected.

watched your video,went to work

removed rear cover of Frig, found valve was cracked and leaking water. turned off water and ordered new valve. After receiving new valve, Removal and installation took about 15 minutes. Pretty easy, a no brainer.

Unplugged fridge, and turned off water supply. Removed cover from back of fridge, followed the plastic tube down to water valve.
I unbolted the mount holding water valve in place, removed the input tubing on top by unscrewing nut. I made a note of which outbound plastic tubing went to water dispenser, and which one went to icemaker, and which side of the water valve they plugged into, and then cut the tubing very close to the old valve.
I slid the tubing into the new water valve, and I felt it lock into place, very easy. Attached the input water line and tightened the nut.
Reattached the water valve mount to the body of the fridge, replaced cover, turned water valve back on and checked for leaks (there were none).
Plugged in fridge, tested dispenser, everything worked just fine. No leaks.

1. Remove back cover from frig
2. Remove Double Outlet Water valve from frame
3. Place towel under valve, remove supply line to filter
4. Cut black and clear lines next to valve, ensure a smooth cut
5. Slide new connectors onto lines, press lines into valve firmly, make sure they slide in all the way
6. Slide connectors into valve locking into place
7. Re-connect filter supply line and re-connect valve to frame making sure lines are in the proper place
8. Replace back cover of frig, do not over tighten screws

I turned the water off at wall. Then I removed 6 nuts removing the back cover. Removed one nut to remove the outlet water valve. Disconnected two bottom hoses and put them on the new unit. Removed top hose and installed on new unit.
When I removed the top hose water did spill out.
I had to rush to connect it to the new unit .

Easy repair. Diagnosis was tricky - this website and popular mechanics article helped me to narrow down the problem to the solenoid water valve.
Unscrewed the left side of the back panel and unscrewed old water valve from its bracket. The steel inlet hose was easy to disconnect, as were the two electrical socket connectors. The two outlet water hoses to the refrigerator were a little trickier. You need to cut them with a blade, and insert them into the new valve, which has teeth to hold them in place. Once I figured that out, the rest was easy. I remounted the bracket, and then tested the water flow successfully. Great website, thanks for the help!

Removed food from Freezer, Unplugged refrigerator. Removed light bulb cover and ligt bulb. Unplugged and removed Ice maker and motor. Removed air duct cover from motor. Unplugged and removed evaporator housing and fan. Pulled fan blade off. Unscrewed brackets from fan motor, removed dust cap from top of motor and grommet from bottom. New motor came with 6 pin connector and four pins for evaporator fan motor. Cut the harness grommet to separate the light bulb wiring from the evaporator motor's. Pushed the the old light bulb pins (red and orange) from old connector and push them in to the new fan motor connector. Reversed the process and no more noise

Removed back lower panel, removed valve, ordered part on internet, cleaned motor and back of fridge. Most time spent was waiting for delivery of ordered part. Part received and installed in 15 minutes after reviewing instructional video included in my email verifying my order, fridge pushed back into place, waited for ice maker to refill.....DONE. So easy. Thanks guys. Job well done.