All Installation Instructions for Whirlpool Range YWFC150M0EB2

Bottom door trim was rusted

Removed oven door and the 3 screws holding the bottom door trim. Attached new trim piece and reinstalled oven door. Entire job took less than 5 minutes.

Parts Used:

Range Trim Lower (White)

Timothy from Terre Haute, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

11 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Oven light would not work--faulty socket

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Parts Used:

SOCKT-LITE

Delores from Warren, MN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

10 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Purchased home but stove had no broiler pan.

Purchased 2 piece broiler pan from this site

Parts Used:

2 Piece Broiler Pan

Raymond from BLOOMINGTON, MN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

16 of 31 people found this instruction helpful.

Was this instruction helpful to you?

Oven wasn't preheating to temperature

Repair of oven sensor easy to install; however, product did not resolve the problem. Returned new sensor and awaiting refund (2 weeks passed so far).

Parts Used:

Oven Sensor

Margaret from WALDORF, MD
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

8 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Both right and left side trims were broken.

Ordered both parts using the excellent breakdown illustrations of the door. Received the parts along with video instructions on how to repair.

Parts Used:

Side Trim

Side Trim - Right Hand Side

A D from HOUSTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Burner would randomly overheat on any setting (Bad Control Switch)

1) Unplug stove.
2) Remove back cover of the stove held in place by 8 screws (4 short ones for the upper holes and 4 longer ones for the lower holes.).
3) Remove the knob from the switch that you are replacing to expose
the switch mounting screws (2 screws).
4) Remove the screws.
5) Go to the rear of the stove and extract the defective switch.
6) You will see 2 plastic plugs going into/onto the switch. Remove the
plugs. MAKE SURE YOU ARE UNPLUGGED FROM THE
Wall OUTLET!! A small flat blade may be needed to separate the
plugs from switch.
7) Attach the plugs to the new switch (there is only one way to do it.
you wont get them confused and put on wrong.
8) Put the new switch where the defective one was.
9) Come to the front of the stove and put your two screws in and
replace the knob.
10) Replace the back cover,
11) Plug in and test burner.

Parts Used:

Infinite Control Switch, 6"

Infinite Switch - 8 Inch

Mark P from CORP CHRISTI, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

The 8-inch burner only heated on high regardless of the temperature setting dialed in.

Unplugged stove from electrical outlet. Pulled temperature control dial off by hand. Remove screws to top back stove panel with Phillips screwdriver. Removed top stove back panel. Unscrewed broken infinity switch from stove. Unclipped wiring harness to broken switch by prying loose with flat head screw driver. Reclipped wiring harness to new switch. Screwed replacement switch back onto stove. Reattached back panel with screws.

Parts Used:

Infinite Switch - 8 Inch

Reginald from PLAINFIELD, IN
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

light bulb in water ice freezer door went bad

I didn't. Don't know how to get to light bulb to change it for this specific model

Parts Used:

Light Bulb - 40W

Carl from RIVERSIDE, CA
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers

8 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Replace aged Drip bowls

Lift and remove heat elements
Lift and remove Drip bowls

Replace Drip bowls and heat elements

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

ROBERT E. from GLENDALE, CA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Generic drip bowls in the stores did not fit

Very easy remove the burner and instill the drip bowls

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Elaine from BROAD BROOK, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Loose terminal caused block to overheat and break

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Parts Used:

Range Main Power Terminal Block

Dana from Black Mountain, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

6 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Oven sensor was not regulating heat set for oven

Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too

Parts Used:

Oven Sensor

Linda from SAINT CLOUD, MN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

I broke a piece of the trim and had to replace it

took the handle off, replaces the side trim piece and replaced the handle. Very simple!

Parts Used:

Side Trim - Right Hand Side

Gregg from SOUTH BEND, IN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

bottom piece of range rusty

took old one off and installed new one used electrical tape to hold glass from sliding.Unscrewed moulding and installed new one

Parts Used:

Range Trim Lower (White)

Bruno from LE ROY, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

My drawer did not line up

Putting the drawer glides on was easy. My range drawer did not have any glides on so my drawer would fall out. The drawer glides popped right on the drawer. The glides for the track were easy to screw into the body of the range. I had to bend the tracks up a little on each side with a pair of pliers. One glide would go onto the track and the other one would go on top of the track. After bending them a little I was able to push them onto the track.at the same time.

Parts Used: