YISE630WS01 Whirlpool Range - Instructions

It turns out that the 6" and 8" burners we actually broken and the infinite switch for the 8" burner was not working properly. These we very simple replacements. You just need to note the numbers on the original burners to make sure that you use the same numbers on the bottom of the burners so that they install in the same slots. The wires on the infinite switch match and this takes less than 5 minutes to remove the back of the stove top and the front switch handle. Simple replace the infinite switch and the burners and whoowhooo ,,.... the fix is done.

removed several screws, removed old controller, installed new controller buttoned back up works perfect

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

replaced control

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Philips head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.

I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted

For the Ikea Range isg650ws01, the repair was very easy.

Step 1) Slide the range away from the wall slowly, verifying occasionally to not strain the gas or electric lines

Step 2) Unplug the range

Step 3) There are 2 phillips heads screws holding the rear panel in place. Remove the two screws and remove the panel.

Step 4) The cooling fan is held in place with 2 phillips head screws. Remove the screws and disconnect the electrical cord

Step 5) install the new cooling fan. The electrical plug can only be inserted one direction, so there shouldn't be a concern that you have the plug installed correctly. Match the original orientation of the fan in the unit. Re-install the 2 screws for the fan, and then install the rear cover. There are 2 slots that the panel needs to slide into in the bottom. Finish the install by installing the 2 screws you removed in to hold the rear panel. Plug the range back in and heat to 450°F to validate the repair.

removed 4 screws lifted off the face with switches replaced the bad switch and put the face plate back on. if you have any concerns just watch the video , part select has posted its great

i removed one screw that held the broken end cap in place, removed it and replaced it with the new end cap attaching it with the same screw.

installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

Removed old element, and easily popped in the new one.

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

easily pulled old seal out and push new seal in place simple and quick.