YGY398LXPQ02 Whirlpool Range - Instructions

OMG you have no idea how grateful I am. My husband and I watched your how-to-video and decided that it looked pretty easy for us to replace on our own. We saved close to $200 between the flat fee for a service call plus labor. Thank you very much. We were also pleased how fast our part was shipped to us.

Visited PartSelect.com and ordered the element. Talked to a really sweet lady who assisted me at the company by ordering the part. Received the part and my husband cut off the electricity to the stove, took off the old element, got the sockets and after pushing on the new element, and he screwed the screws back on, cut on the electricity and we cut the stove on and it was ready to go. VERY, VERY SIMPLE TO REPAIR.

After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.

I did exactly what your instruction video showed. The most important thing to remember is to TURN THE POWER OFF FIRST.

Remove top oven door,remove two hex head screws located underneath cook top at the front on both sides,slid the range top forward approx. three(3) inches to obtain access needed to unplug the wiring harness, located behind the vertical part of the cook top,removed the cook top,placing it on a padded table with the glass side down,disconnected the three (3)wire spades and unscrewed three screws anchoring heating element to the cook top frame, replaced defective heating assembly with new. Repeated above steps noted above,in reverse order. And yes, all work was done after power was shut off at power panels dedicated oven circuit.

unscrew 3 screws under the control panel and pull that away from the glass top making sure the wires don't come apart from the connectors. care fully slide the glass forward and replace the burner which was the easy part. DO NOT try to test without making sure that none of the burner are touching the metal surface!!!!!!!! it will trip your breaker. But now we have a range with 4 burner after a year THANKS

Had to screw off old terminal block & screw on new one

Removed oven from the wall. Take off back panel. Removed thermal overload thermostat. Replaced with new part and works great.

I watched a video on line about how to do the baking element. I did not want to take the door off so it made it more difficult to get to the back where the connections are located. The broiler element has screws holding it up where the over element is resting on the bottom. The video said that you should test the conductivity but I did not have the object needed to do that. It was supposed to solve 99% of the problem to just replace it. When it was removed, I could see that it had a hole blown out on the coil. Problem solved without a repairman needed which would have cost alot more and I still would have needed this part.

I did some research on blogs and identified the thermal fuse as likely culprit. Ordered part from PartSelect.com, but had to call the 800 number because the parts diagram doesn't show this fuse, just the thermostat. The fuse is located on the back of the oven, so it must be removed from the cabinet, but that wasn't a huge project. There are a bunch of sheet metal screws holding the top and back covers that must be removed. The fuse is held on by two screws and has two wire connections. Getting the stove out and disassembling is the hard part, but not really difficult if you take your time. I used a foot stool that was about the same height as the bottom of the oven and just slid the oven out on a piece of cardboard. Make sure you turn the power off before starting.

Disconnect the power.took the cooktop off the range. Turned it over. Removed the underside plate. Disconnected the bad element. Pluged inthe new element. Replaced the under plate. Reconnected the range to the stovetop .put cooktop in place. Reattached screws. Turned on power. Worked perfectly.

Turned off the power/ unscrewed the oven from the cabinet and slid it out took the back off the oven and the part was right there. What I would like to know is why this happens so frequently? This is the 2nd time and it always happens after the self cleaning is done.

First turn off breakers for cooktop. Reached undereneath the cooktop and pushed it out and set on the counter. (1) unscrewed the frame holding the glass and removed it. (2) pulled glass off. (3) Unhooked the burned out element after identifying wire connections so I could connect the new element correctly. (4) Put the glass back on the frame. (5) Placed the frame over the glass and screwed it back to to frame. (6) Moved cooktop back into place. (7) Turned breakers back on and turned element on and it was operational. It was a very easy job.

Removed trim strip from each side of oven, removed one screw from each side hat held oven in place and slid oven out of wall. Finally found the thermostat located on the back side of the oven after removing the sheet metal on back. replaced the thermostat and reversed the procedure. Only difficult part was locating the thermostat. I thought it was on top, when in fact it was on the back. Pretty easy, really, and saved some cash in the process.

I was able to convince a local mechanic that he could do this after watching it done four times. The most difficult part was unscrewing and taking out the oven to get to the back. He suggested since this has happened everytime I used the self-cleaning feature, that I cut a hole in the wall for easier access (tongue-in-cheek). The most difficult part was dealing with the extended warranty service plan - this is covered, but they could not find a technician to do this. Then I found out they don't pay mileage so who would want to come out to a rural ND ranch to repair an oven?