YE20FN2 Magic Chef Dryer - Instructions

Step 1. Read all the comments about how to do this job in this forum. (i found them very useful)

Step 2. Read the directions that come with the dryer (they helped a lot)

Step 3. Don't forget to disconnect the power cord before reattaching the door switch wires (oucH! ) or doing anything with your dryer.

Removed the two screws holding in the Filter and removed the filter.

Removed the two screws holding the front onto the dryer.

Put the belt over the drum and proped the drum up.

Reseated the tension spring and pully in the proper slot. (On my machine it is the position closest to the motor).

Reassembled the dryer in the reverse order.

-Took top of by prying with screwdriver.
-2 screws and door wire to take off front panel.
-proped drum with 4X4 piece of wood.
-looped belt around drum where the mark for the old belt was.
-looped belt through tensioner and pulled with the screwdriver over the motors drive shaft.
-manually spun drum to make sure everything was right.
-put panels back on and was done.

You cant go wrong with the included directions and belt diagram. this is the first repair I've done of any kind that went flawless.

I watch the video and played it again while I was working.
I am a 54 year young woman and I did it.

Removed the two screws at the back that hold the top of the dryer. Then I pried off the top at the front by inserting a screwdriver into the front to remove the top from the clips. Then I tilted up the top like a car hood.

I removed the two screws inside that held the front on and lifted the front off. Because of the wires attached to the front, I made sure to turn the front aside without pulling on the wires. After removing the broken belt, I put the replacement belt over the front of the drum, lifting the drum a little. Then I threaded the belt over the drive and around the tension wheel per a diagram I found on the web.

While I had the front off, I removed the lint trap and cleaned out probably decades worth of lint.

Then I replaced all the parts in reverse order, plugged it in and had a working dryer!

I pried the top of the dryer with a screw driver and then lifted the top of the dryer, I then removed the two screws "with a nutdriver" that held the door in place and then removed the door and drum. I then got the new belt and placed the belt over the drum and positioned the belt through the idler arm and then on the motor pulley. I had to hold the door and drum to lock the bottom of the dryer door to the dryer and then made sure the rear drum seal was in place and the belt did not slip off the motor pulley

The dryer was not difficult to repair. The diagram that came with the belt made the repair easy. The repair part came in a very timely manner.

Watched a video and went to town taking it apart. I stuck a pop can under the barrel to hold it up while I worked on pulleys. My dryer does not have a plastic pulley but a metal tension bar with a hole in the middle. Ran upstairs and watched a different video with my set up and all was good. 5 min of work 5 min watching Youtube and 5 min cleaning all the lint out of the machine. I am actually glad the old belt broke because some of the lint was in a clump and had scorch marks on it. I took the shop vac to every part of the cabinet and shoved it down the lint trap sleeve also.

Removed broken filter, used screwdriver to clear out some old lint in the intake and inserted new filter. New filter fits and works as described.

Buy the part the site provide a video on how to do it and was very helpful thanks

Watched the video on the site and it was spot-on! Super-easy, took like 10 minutes to replace the belt. Thanks!

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

Screwed the new “$40” dollar light bulb back into the recessed socket. The new bulb is much smaller that the original bulb and much harder to get fingers into small area where the bulb went. After several try’s, I got it in.

Needed a belt. Only snag was for me was re-installing front panel (door)

Raise the top and then remove two screws to remove front. Once the front was removed on this Maytag model it was not necessary to remove the dryer drum. I simply lifted the drum slightly and slid the belt around the drum to position the belt. I then pressed the tension arm toward the drum and fed the belt around the drive pulley and tension pulley. I spun the drum a few turns by hand to insure that the belt was aligned properly. Then replaced the front cover and the top. Turned on the dryer to test and job was completed. Thanks to your video and prompt parts delivery the job was a snap. My wife didn't even have time to get mad.