XDF400PSN2SS General Electric Dishwasher - Instructions

The installation is fairly straightforward, basically one plug in electrical connection and two plumbing connections. The smaller of the two plumbing connections can be tricky because of the hose clamp... The original clamps are one time use crimp style. The replacements are standard hose clamps, which means the section where the tension mechanism is, is a bit wider than the clamp itself... This can cause the rubber collar on the dishwasher to slide off/separate from the pump part itself when tightening the hose clamp. If you are careful and align things just right, it will work like a charm. The best advice I have is to take your time and make sure the connections are snug without being too tight, otherwise it could leak and/or something else could break.

just bolted on the new one and hooked up the hose

Took old valve assembly off and replaced with new assenbly

1. Turn off the water.
2. Turn off the power to the dishwasher.
3. Pulled out the dishwasher.
4. Tilted it forward and to the side with a bowl to collect the water at the bottom.
5. Carefully laid the dishwasher on its side
6. Removed the existing pump. Make note of its orientation before removing (maybe take a picture). Disconnect the wire and loosen the 2 pipe clamps used to attach the pump. The pipe clamps were not the adjustable, reusable kind but the replacement part came with several.
7. Put the new pipe clamps on the hoses (the supply and discharge side) so they're in place.
8. Installed the replacement pump by pushing it on to the supply then the discharge hoses.
9. Move the clamps into place and tighten.
10. Reconnect the power wire.
11. Stand the dishwasher up.
12. Turn on the power and water.
13. Run a quick test to make sure it's working and doesn't leak.
14. Push it back in to place and reattach it to the cabinets.

Started by removing dishwasher, including disconnecting power, water and drain line. Then turned washer on back. Electrical connector to old wash pump was a little tricky to remove as the release tab isn’t straightforward, I used a tiny screwdriver and jiggled it around till it came loose. The factory hose clamps (2) are crimped on, but if you can find the tail end you can work them loose with a screwdriver by prying the tail up from the body of the clamp. Once you have the electrical connector and the two clamps removed, the pump comes of easily with a twisting motion. The new wash motor came with new clamps (2 extra). When sliding the rubber boots on the new pump in place, it will require a twisting motion to position it correctly, make sure (I didn’t and had to go through the whole process twice) that the rubber boot is not folded under on the bottom where it’s hard to see. Tighten clamps carefully and don’t over tighten. Plug in electrical connector and you’re ready to reinstall dishwasher.

Unplugged power.
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.

It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pump and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.

Took it out of the box and set rollers on track
rolled in place ALL DONE

Twist counter clockwise to remove clockwise to install

My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine

Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

the design of this part is easy to break when closing the top rack.

there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher

the part broke when closing the rack [a dish too tall hit it]

it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel

Release DW from cabinet and pull out, Unplug power.
Remove kick plate and unplug door cable.
Open door about 6 inches and using socket back out 2 bolts at bottom of door corners.
Pull door up off hinges about 4 inches and slide old gasket out and install new gasket in place.
Reset door on hinges and reinstall bolts.
Plug door cable in and reattach kick plate and plug power cable in.
Push DW back in place and attach to cabinet and adjust kick plate

Got the seal, read the reviews to see how to do it, Take out the two bottom screws ,easy enough. pull the door up ,pull out seal replace new one. Easy enough, but know one said don't pull the door up too high , I did, could not get it back down to save my soul. Needles to say had to buy a new dishwasher. that sucked have the new seal gasket if anybody needs one