XAV13PRBWW Maytag Washer - Instructions

I unplugged the machine, tipped it back slightly and rested in on a gallon paint can. I inspected the under side and manually advanced the fan belt to hear if I could hear the noise at the water pump. The pump pulley and shaft was worn and there were metal shavins (small) on surface of pulley.

Then I removed the belt from the pulley, rested the machine back to normal position, removed front panel (two sheet metal screws on inside top), removed the water pump hoses (htere is water int he hose & pump assembly so you will get some water on floor.

Then I removed the pump and ordered a new one. The installation was the reverse, machine works like new and the washer tub spins better than ever during the final rinse and spin, since the worn water pump was binding and stressing the machine.

Thanks to Part Select - Your website is awesome and your service instructions and user advice gave me the confidence to do the repair myself. I saved $150 - $250 for the repair.

I found the mostly likely parts to fix my problem on the website... that washer would not start, stating the lid switch assembly fixed the problem 66% of the time. I used an ohmmeter to test the switch and could not find any continuity. Replacing the switch took less than 5 minutes. Easy.

Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos

Part Select data showed that over 60% of the time, this issue of the washer shaking was due to broken support springs for the tub and over 30% of the time, it was a worn/broken snubber ring. So, I initially purchased the six springs and snubber ($30 total) from this site and completed both of those repairs. I leveled the washer securely and tested it again. However, the washer still had the issue of shaking during the spin cycle with no improvement. So, I then researched again for this issue and parts recommended were a lower bearing kit or transmission. Since the transmission replacement was $429, that wasn't worth trying. So, for the $52 lower bearing kit, I ordered it from along with a new belt ($22) (even though the existing belt didn't show any signs of significant wear, but I changed it anyway). The new bearing kit was installed and the washer is now operating like new. I used the current videos on the website for replacing the parts that I ordered, and they were perfect step by step instructions. It made the repair very simple for anyone with any sense of do-it yourself ability and with minimum, ordinary tools. So, for approximately $110 for parts and doing the repair myself, the washer is like new again. Thank you!!!!

Followed the great instructions on your video

Repaitmr was simple. Followed video instructions from web site. Problem I ordered wrong motor so it just blew my plugs fuse. Also needed pump. Changed motor to old motor installed new pump. Machine works great.

raised the top of the washer to get at the front panel screws. Removed the front panel. Removed the cracked hose and installed the new one. Reinstalled the front and top panels.

Removed front panel by releasing spring clips with putty knife and removed two screws with a ratchet and 5/16” socket. Removed rear access cover with a ratchet and 5/16” socket. Removed and replaced tub to pump hose. Loosened clamps on each end of hose with channel locks.
Re installed rear access cover and front panel.

I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!

Removed the front panel with a screw driver, removed the old bumpers with a pair of pliers, replaced the bumpers and replaced the panel. All was very simple and took no time. The video on your website was most helpful. Thanks

I watched video, couldn’t believe how easy to replace

After receiving the new part, I lifted the lid making sure it was level, then simply pushing the new pin in the lid hole, then pushing the whole thing back toward the corner of the lid until it clicked in.

I popped out the hinge pins, popped outthe busshings, popped out the cam. time less than 10 minutes, pressed in the limit cam, pressed in the bushings, pressed in the hinge pins. time about 5 minutes. the most important thing is my wife is extremely happy. I'm happy the parts fit perfectly.
also the parts arrived in 2 days.

Unhooked the macine pulled out for easy access .removed drive belt rear cover plate ,vaccumed remaining water out thru drain hose with wet and dry vac. Removed hose clamps and hoses .removed the three hex screws holding the pump to the base plate. The removed the old pump , Installed the new pump hoses access plate and belt . Hooked the machine up . Worked perfect.











the

Removed screws that held the control panel to the cabinet, found wiring diagram. Found I wasn't getting voltage past the lid switch when the lid was closed. Went to Partselect.com, entered model number, quickly found detailed diagram showing switch with price and availability. I ordered switch, received in 2 days. I disconnected the wiring harness from the old switch, I popped the old switch out, installed the new switch, reconnected the wiring harness and closed the control panel. I tried the washer and it worked right away. Saved at least $100 by not having to call repair man. Very happy with Partselect.com, will definately use again!