Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This splutch cam kit is a genuine replacement assembly designed for select Whirlpool, Maytag, and affiliated brand washing machines. It plays a critical role in the wash and spin cycles by engaging th...
This basket drive hub kit is a vital component in select washing machines, designed to connect the wash basket to the central drive shaft, enabling proper rotation during wash and spin cycles. It play...
This genuine OEM drive belt is designed to transfer power from the motor to the drum in select Whirlpool, Maytag, Kenmore, and other compatible washing machines. Operating at 115 volts and 60 Hz, the ...
This genuine OEM suspension rod kit is designed to support the inner tub of your washing machine and minimize vibrations during wash and spin cycles. If your washer has started making loud banging or ...
This is lid lock designed for use within various washing machines. This lid lock, also known as a latch assembly, is used to secure the lid of your washing machine during the washing cycle. If your wa...
This water inlet valve is for washers.
The water inlet valve controls the water flow into the washer.
Unplug the washer and shut off the water supply before installing this part. Wear work glove...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
This washing machine cleaner includes three time-release tablets designed to remove odor-causing residues, grime, and buildup from high-efficiency and top-load washing machines. The tablets work by cl...
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
$7.47
In Stock
Order now and your part arrives by May 9
Questions And Answers for WTW5000DW1
Ask our experts a question about this model and we'll get back to you as soon as possible!
138 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sandi
February 23, 2020
Washer is making a grinding sound and will not agitate or spin
For model number WTW5000DW1
Hello Sandi, thank you for your question. There are a few parts we would recommend checking to determine the issue. They are Drive Hub Kit Part Number: W10528947, Washer Drive Pulley Part Number: W10721967, Shift Actuator - 6 Pin Part Number: W10913953. If those parts are ok, the issue is probably the gearcase and transmission Part Number: W11035751. I hope this helps.
17 people found this helpful.
Did this question help you?
Thank you for voting!
Jeff
December 5, 2019
The washer will start and pump in water but will stop after about a minute. It won't continue to the wash cycle. If i open and close the lid the water will start pumping again but stop about 30 seconds to a minute later.
For model number WTW5000DW1
Hello Jeff, Thank you for the question. This could be an issue with a defective Door Lock, PartSelect Number PS12704713. This lid switch assembly is for a top load washer. The lid switch assembly detects if the washer lid is open or closed and prevents the washer from starting the cycle. Hope this helps!
Sensor light blinking off and on can not start a wash. Not draining water in washer.
For model number WTW5000DW1
Hi Mary, thank you for your question. When your appliance is not starting there are a few parts that you may want to check, however you could try and do a reset on your machine. Generally how to do that is unplug your appliance for 30 minutes and then plug it back in again. If the issue continues the first part to take a look at would be your door lock: PS12704713. If that part is fine then you may need to take a look at your switches or control board for being the issue. Good luck with your repair.
7 people found this helpful.
Did this question help you?
Thank you for voting!
PAUL
November 28, 2019
We had a power surge. Unit will not turn on. I there a fuseable link? Does the motor have a reset?
For model number WTW5000DW1
Hello Paul, Thank you for the question. Normally this indicates the control board PartSelect Number PS12114296 had shorted out by the surge and may need to be replaced. Hope this helps!
Starts to spin or agitate, then stops. Is this the transmission?
For model number WTW5000DW1
Hello, Thank you for your question. Here is some information on how to test the parts in the washer to determine if the issue is the agitator or the transmission: https://www.partselect.com/Repair/Washer/Not-Agitating/ . We hope this helps, good luck with this repair.
4 people found this helpful.
Did this question help you?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read moreand put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned
... Read more it back up and got caught up on laundry. good day when the washer is fixed.
