WT4870CW LG Washer - Instructions

I first fixed the stator coil by repairing the cut coil spots at 2 location using solder and with a bit of equivalent wires to extend with heat shrink sleeving to extend over the iron core. Next, I assembled the new coupling in the new coupling assembly with a bit grease around cogs. Wached few videos to see orientation since mine was broken assembly and wasn't certain how it sits inside. Once oriented and seated right, I wiggled to sit in properly over the stator cog..I felt the stator cogs with coupling locked to the shaft. After that I secured the main nut and connected the appliance. All worked perfectly after that. Thanks for sending the ordered parts. Now the washing machine is strong and solid in its agitation.

raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new leg was a breeze.

unplugged machine, turned off water valves. Moved machine away from the wall. Disconnected supply lines. Removed cover housing water valve assembly.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turned on water supply valves. Done.

Tried to remove adjitator but it was stuck. Could not find any professional method of pulling it. There must be some type of puller,

Since the old pulsator had actually come off during a wash cycle, I was able to place the new one on easily. Tightened the screw with a socket. Then placed the new cap on. Before placing the new pulsator on, I was able to clean all the mold and hard deposits off the mechanism under the pulsator. The hard deposits were also scrapped from the pulsator holding (where the screw goes) which may have caused the problem to begin with.

Very close to the installation video online at Parts Select. Removed the back panel, unclipped the hose from the inner fitting and replaced with the rear hose. Why it didn;t leak on the inside is interesting as there was no clip on the at the inner fitting.
The one difference from the existing install video online was that I didn't have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).

Tried everything and could not get it out I just use mesh bags for washing at this time, but LG washing machine is the worst I have ever had

Very simple repair after watching YouTube video on how to complete repair.

I HAD A CHAT WITH LG EXPLAINED THE PROBLEM . SAID IT WAS THE WATER SHUT OFF VALUE. V EVEN SENT THE PAGE WITH PART# TO ORDER ONLINE.

LOVE LG CHAT!!!

The old dispenser is removed by slightly raising the front as you pull it out of the housing slot. To install the new dispenser, keep the front slightly tilted up and insert the new dispenser into the housing alot

The problem ended up being the pump motor which discharges water from the washer. I figured out this was the problem after trying several things. I determined the motor was fine when it was empty. With the unit turned off, if you can rotate the tube with a quick spin and it lights up, probably this is OK. Then I tried to run it again and it went about 1/2 way through the cycle and stopped and started humming again. So I started emptying out the water, which I noticed was about 5 gallons which is way too much. so once empty, I took the pump off by turning unit on side. There are two hoses with hose clamps, and a few screws. Be careful to mark which wire plugs onto which side of the pump. One is brown and one is black. If you take the pump housing off, with the 3 screws, you should be able to pull the motor apart. Mine had water and scum from the wash in it, which was a dead give away that it was the problem.

Once i got the parts I removed the top so I could get to the hangers. I removed the broken parts and replaced them with the replacement parts and rehung the tub and replaced the top.