WRX735SDBH00 Whirlpool Refrigerator - Instructions

Easy fix, it's right in the back of the fridge under a cover that just clips in, a piece of foam, and two screws. The hardest part is getting the clips free without breaking them. After replacement it's silent instead of making a grinding noise regularly.

Remove back cover
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.

This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Truth is, this took a couple hours of cursing, but that was due to poor information and no prior experience. I imagine the next one would take 20 minutes. The issues are these: videos tell you to use a putty knife to pry the old switch out. That is harder than it seems because each switch has a plastic spring that pops open to hold the switch on, and you can't access the spring when the switch is installed. So it is important to use the knife on the side of the switch (left or right of spring -- look at the new switch), and back and forth until the switch is worked out. Then it can get worse. The new switch has to plug in electrically before it can be installed mechanically. In my case, with the switch on the fridge wall rather than the top, the outlet for the plug was encased in foam insullation. That gives the appearance that the plug was fixed, immovable, which makes it impossible to plug it in electrically before the switch is in place, and of course once it is in place you can't then plug it in. The problem here was poor instructions. Just scrape out a lot of the foam around the plug and you find that the plug is really not fixed, but attached to reasonably long wires that allow you to plug it in with the switch a couple inches from the wall, and then insert the switch. None of the online instructions tell you this about the wires.

The old cover was off and I just slid the replacement part that I got from you'll, it just slid in place and snapped close. Perfect fit. Thanks guys

Simple. Just put it on the racks provided in the fridge. The part fit perfectly and took literally 5 seconds to put it on.

I safely unplugged the power from the refrigerator first before starting the repair. I then had to remove the bottom access panel which is secured with hex head screws, then disconnected the two plugs from the two failed parts that connects to the appliance compressor. After installing the replacement parts and returning power back to the refrigerator I buttoned up the access panel and I waited at least three hours to turn the cooling system back on. This allows the coolant in the compressor to settle. The two replacements parts fixed the cooling system.

Removed old shelf and installed new shelf. No tools required

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Pulled the whole assembly out and unscrewed the Ice maker and old wire harness loose. pulled one wire at a time loose and put the new one in place one wire at a time so not to get them wrong. Then the ground wire I cut and stripped and used a wire nut to connect the two green wires together. Otherwise you would have to take more things off to get to the 1/4 nut on the ground wire. Then put the three screws back in the ice maker bottom.Slid it back in place and plugged in the new wire harness. And put the plastic cover back in place to cover the wires. You can also look on U-Tube to see how it is done. They just do not show the new harness I was sent. I guess the ice maker I got fit other models.

I ordered the wrong part for my refrigerator. The refund processed easily. However, the email that I was promised with return instructions has not been sent. I have asked several times about how to return this part and total silence from partselect. I'm ready to throw this replacement bin in the trash.

Open and remove door by loosening two screws on both sides of the door. Lift up and away the door.place the door on flat surface, grab and lift up on seal pulling out of reach. Clean track, alone seal on food before pressing in place. Check to make sure seal is set in place. Install door job done.

Let the ice in the freezer melt while installing P trap drain tube

you tube video was most helpful. after getting new part and disassembling old ice maker, you have to change out the wiring harness. Reinstall ice maker, don't worry about the timing of the unit as it will do this itself, may take 10 hours to produce ice, mine took about 2 hours to go through its' cycles and give me ice. It is running great

Access back of unit, lower left corner. Remove wire capacitor retention clip. Unplug cold capacitor, plug in replacement, reinstall wire retention clip, test.