WLP83200 Whirlpool Range - Instructions

removed the screws that secured the lower element. Disconnected the old element from wire contacts. Inserted the new element into the wire contacts.

This job replacing the was so easy, it took about ten min,to do it thanks

looked it up on line how to change it. before I ordered part, to see how much of a job it was. was real simple to change, had no problem. also part select sent the correct part. Job went well

Opened the range surface, changed the large surface element. One of the wire was different to unplug. Need someone else to hold the panel. It was not a tough job.

Removed top of stove replaced heating element ,piece of cake.

I was able to remove the door by opening it partially and lifting it up while jiggling it. Once off, I laid it with the inside up on a table and the screws along the bottom facing outward so I could access them easily. I removed the various screws and porcelain covers and sides feel of easily. The inside panel lifted off exposing the inner glass and frame. The screws and clips had to be sprayed with penetrating oil to remove them. The frame lifted off and the cracked glass was removed. I was careful to wipe away all the fluid used to loosen the frame clips. Assembly was the reverse of this being careful to let pieces fit nicely without force. It would have cost me $39 to have the repair performed assuming I could get the door off. A Phillip's head screwdriver was not adequate to remove the frame clips. You needed a correctly-fitting square drive.

I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in

I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!

Removed the element by using a basic screw driver...two screws. Detached the slip on wire attachments (don't know what they are called). Re-attached new element and screws. Very simple. I was hoping elements were a little cheaper, but I was impressed with the speed that Part Select delivered my new element. I'll use them again.

Step 1. Always ensure appliance is unpluged from power source. 2 Remove oven door by open slighly and lift up be sure your hands are up from hinges they can snap back and injure fingers. 3. Have a cover on a flat surface and have a diagram of oven door, 4. Remove bottom screws and slide out top glass and side rails. 5 Remove top cover and insulation over glass. Beware of any jagged glass. 6. Incert new glass. 7. Be sure when replacing insulation and cover that cover in under tabs to ensure glass is firmly held in place repeat steps in reverse order. Took just 20 minutes to repair. I used a small electric screw driver.

Although I put 15-30 mins for repair, most of that was taking it apart only to have to put it back until I got the right part. It can be done in 15min or less. FIRST: UNPLUG THE RANGE or Shut the circuit breaker OFF. Remove two screws (1/4" nut driver) on the front lower edge of the cooktop. These are seen once you opent the top oven door. Lift up the top and pull out about two inches and disconnect the multiwire plug in connector. Lift the top off the range and place it upside down on a flat surface (talbe or counter) protected with a towel. Unplug the sliding connectors from the burner unit noticing the correct placement. Remvoe the two tabs (#2 phillips screwdriver) on either side of the burner unit noting location. Take the time to clean up all debris with a vacuum or soft cloth. Install the new burner, connect the two tabs, plug in the connectors, return the top to the range, plug in the multiwire plug, secure the two screws and plug the range back in and start cooking!

Remove power from appliance, verify power is off. loosen two side screws that hold cook top to counter top. Gently push appliance up from bottom, everything from now on is done gently !. every component is very fragile. hope you have enough room to move cook top to side, if not, have help to hold it for you. #2 screwdriver, remove screws on all sides, two front, 3 sides, 3 in back. Note placement of connected wires in the affected element. # 2 screwdriver remove one screw on bar holding set of elements, lift and loosen metal spring and remove element, ply wires off with pliers. ( I suggest you clean inside cook top if needed) Note place of springs(Numbers) and remove to place on new element. reverse order to complete.

The part came in 2 days even though I chose the least expensive shipping method. The hardest part was unscrewing the old screws that held the old bake element in place. We soaked them in WD40, and after a while were able to unscrew them. The new element slid in place and works just fine.

Open oven door and remove two screews with 5/16 nutdriver to remove hole top of stove.Just lift up gently on front of top and pull toward you and when about 4 inch clearance on back of top you will see where all the wires connect ,press the side tabs of this big connector and it will release very easy to remove the top.Place top on bath towell upside down on countertop and remove 4 screws and 2 clips on the bad burner with the same 5/16 nut driver and remove the three wires and reinstall the same way then reinstall the top on the stove in the same order.Very Easy Job

pulled door up and out. Disassembled door. removed old glass and rope gasket. installed new glass and gasket.