Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
temperature not accurate after 3 1/2 years of happy usage
Opened up the back of the stove. Unpluged the sensor. Replaced the sensor. Replace the back of the stove.
The sensor that has been replaced is not what is expected. After reading all of the instructions for adjusting the temperatures, the only temp that stays steady is when we first turn on the oven to 350 degrees. That stays steady but when I turn it to 400 it slowly goes up to 425 degrees.
mice had made nests in the insulation wrap in the range
I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.
This is not the best design. You'll need to have an extra set of hands to hold the trim pieces in place. Remember the glass is positioned outside [on top of]the trim pieces. Be careful as the trim pieces are rather brittle and can be hard to locate in their proper position. Position glass in the holding tabs at the bottom, hold glass against the trim pieces and gently position door handle over glass and trim.The handle holds everything together. No instructions are shipped w/ parts.
Replaced igniter and also DSI/direct spark igniter did not fix problem. Called out repairman turned out to be bad gas valve. Replaced that part , now stove works fine.
After reading many forums found that this error happens when trying to clean the oven and there is a failure in the latch motor to lock the oven door. It was suggested 1st to just tunr the breaker off to the over wait and then turn it back on to see if the error would clear by itself. If not then you'll have to do what I did and buy a new Latch Motor and replace it. Fairly easy to do: ) Move oven to get to the back panel ) Disconnect oven from power ) Remove the 8 screws to get the back panel off ) REmove the Latch motor screws (2) and remove the motor after twisting to get the latch rod off ) Put in new latch motor by 1st putting the latch rod in the motor assembly ) Screw the new motor in place ) Replace back panel ) Power on Oven DONE!
Socket Lite come with clips attached to the outside of the housing. After you unhook the 3 lead wires that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you snap in the new unit. Attach the 3 wire leads, put a oven bulb in the socket end, and the install the light cover
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Since no instructions are provided with the part and not having seen the oven with the glass door in place, the major problem was figuring out how things went together. The top handle MUST be removed and the bottom trim need not be (although I had already done so). After removing the top handle the glass slips into the bottom trim easily, but the edges set ON TOP of the side plastic trims (left and right), not under the edge as it would appear if you have never seen the original door in place. Properly positioning the glass door then lets the top handle slip back on and the two screws replaced to hold it all to gether. Another pair of hands helps hold it all together until the top handle is fixed back in place. It's quite simple in reality, and instructions would have made it so.
Google the error code that the range was displaying and found others with the same symptoms. Then found several people that had fixed the problem by replacing the oven sensor. I then ordered the sensor and replaced it, which fixed the problem.
We removed the door from oven assembly and laying it flat on the bench removed the stainless steel cover from the rest of the door. Removing the shattered pieces of safety glass was done heating and scraping off vinyl tape.(difficult.)Caution! Do not allow any pieces of glass get under the stainless steel cover, it will leave ugly scratches! We purchased double sided vinyl tape 1/2" wide, 1/16" thick and aluminum "Flue tape" (600 deg. F) 1 1/2" wide from local hardware store to replace the original ones in their previous location. Fitting the new glass on sticky tape has to be done accurately. (no problem). Assembling it was little tricky but still within the ability of a do-it-selfers. We wondered if we should not put the rough side of the glass facing in or out. The original was with the smooth side out so that what we did. If any additional scraping of accumulated grease is needed especially on the inside glass, it requires more disassembly, but we would strongly suggest doing it (we did), while it is all opened. To our surprise the glass arrived by Fed Ex within 24 hours of ordering and now our Whirlpool is gleaming like new again. The cost of this product with shipping/handling by PartsSelect was much lower than ordering it from the other "original" source. Thank you! Sincerely Fred T.
part did not fix the problem, may be gas regulater ,well if you are changing this part,not to bad .remove the knobs bottom screws and two side screws front cover flips up and off ,the ignition control is in front of you right side ,remove the one screw that is looking at and everything slides out .i turned off the gas and elec and removed the gas line and carefully laid the stove on it back.made it easier ,good luck
Inside brass liner in socket came out when bulb was removed. Apparently had welded itself to the base of the bulb
Removed oven from wall unit and took the back off. Removed the old socket assembly by depressing the ears and forcing unit into the oven. The electrical wires were easily removed since they are spade connections and slip off. They also are different sizes so that there is no chance of erroneously putting them back in an incorrect order. The new unit simply slips in from the front and snaps into place. The most difficult part of the entire process is removing the old unit. A little "friendly persuasion" is required to get the old unit out.
The web site was easy to navagate and locate the correct part. The part was in stock and shipped the next day and was delivered in 3 or 4 days. All total the replanement was less than a week. The replacement was easy except it took a second person to hold the glass in place while i threaded the hold down screws fron underneath. I could not hold the glass and thread the small screws with just my two hands, plus having to thread the screws from the bottom was more difficult, but all in all it was simple and now we have a new unbroken glass front oven door.