EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
Back
Back
Back
Keep typing for more specific results...
Keep typing for more specific results...
Models > TX518VE > Instructions

TX518VE (P1322502W E) Amana Refrigerator - Instructions

All Instructions for the TX518VE
91 - 105 of 129
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
chipped the support post while cleaning fridge.
removed 2 crisper drawers. took off glass self. lifted frame and removed broken support post and replaced with new one. popped glass shelf and 2 drawers back in place. done in under 5 minutes.
Parts Used:
Crisper Drawer Cover Support Post
  • Nancy J. from Chepachet, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Leaking at fill tube
Removed fill tube and replaced it with new.
Parts Used:
Refrigerator Ice Maker Fill Tube Refrigerator Plastic Tube Insert
  • Jana from McKinney, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broke the arm off the food compartment rocker switch
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Parts Used:
Refrigerator Door Switch
  • David from St. Pete Beach, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Both light bulbs had been replaced, but lights did not turn on.
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Parts Used:
Refrigerator Door Switch
  • Richard from Arlington, MA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Had to completely remove the ice maker in order to install the replacement part
Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.
Parts Used:
Refrigerator Water Fill Cup & Bearing
  • Leonard W from Roseburg, OR
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Part Where Ice Maker Arm Fit In Broke Off
Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect
Parts Used:
Refrigerator Water Fill Cup & Bearing
  • Yvonne from Worthington, IA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Fridge door was opening too far / banging wall
took the fridge door off, took off old part that didn't work, replaced with new metal door stop (small part). Perfect-o problem solved with a $5 part! Customer Service here was AWESOME! THANK YOU! WILL SHOP HERE AGAIN.
Parts Used:
STOP-DOOR (STAKE$ PIN)
  • Dave from Harwich Port, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Switch didn't work
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Parts Used:
Refrigerator Door Switch
  • Don from Laramie, WY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
broken water fill cup
empty frezzer take door off unplug wires going to ice maker unscrew/bolt icemaker replace door take motor cover off ice maker remove screws on motor replace ice cup and put every thing back together
Parts Used:
Refrigerator Water Fill Cup & Bearing
  • augustine from cedar rapids, IA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
No Ice do to water fill cup & bearing was damaged
took off the ice maker, unscrewed the body, replace icemaker shut-off arm, water fill cup & bearing, reconnected the unit & have ice now, Thank you PartSelect
Parts Used:
Ice Maker Shutoff Arm Refrigerator Water Fill Cup & Bearing
  • Joseph from Kings Park, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ordered ejector arm.
No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.
Parts Used:
Refrigerator Ejector Arm
  • Joyce from Springfield, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
light switch sticking
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.
Parts Used:
Refrigerator Door Switch
  • Paula from Rush, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
exchange of defective light rocker switch
1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch
Parts Used:
Refrigerator Door Switch
  • Steve from River Edge, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Light in the refrigerator didn't work
I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.
Parts Used:
Refrigerator Door Switch
  • Anthony from Fairport, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Light switch went bad
Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th
Parts Used:
Refrigerator Door Switch
  • Joseph T. from Morgantown, WV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the TX518VE
91 - 105 of 129