All Installation Instructions for Estate Range TGS325VQ1

oven would not completely heat up, only heating to about 150 degrees Temp.

contracted a repair service person

Parts Used:

Range Bake Igniter

Isaac from MATTESON, IL
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Paint peeling from strip

removed 3 screws holding the strip and replaced with new strip

Parts Used:

Range Trim Lower (White)

Myron from Punta Gorda, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

oven handle broke

new handle arrived black for white oven - screws did NOT fit new handle- glass came off the door when removing old handle

Parts Used:

Range Door Handle

Jim from CAMDENTON, MO
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Stove would not light due to faulty electronic ignighter

Very easy repair, simply remove old ignighter and install new one. Take pictures if you need help remembering where everything goes.

Parts Used:

Range Bake Igniter

Victor from SAINT PETERS, MO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven would not maintain Heating

Following details from the installation video, after removing the main gas line and the two output lines I removed the four screws that removed the valve but found it was easier to remove and install the new one if I first removed the oven burner(it made for lining up the valve nozzle to the burner easier) from the inside, 3 wires attach on the side towards the stove taking one wire from the old valve and putting it on the new valve in the same place. Everything went back together just fine, I did have some problem with tightening one of the two gas lines for the output and found I just had to keep tightening it a little until there were no bubbles appearing when I applied soapy water to the connections, other than that it was very straight forward.

Parts Used:

Range Gas Valve

Cheryl from WEST JORDAN, UT
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Didn’t work

Took out old one but electric hook up fell in the hole had to fish it out also dropped a screw in the hole could’ve find it used a different one

Parts Used:

Range Bake Igniter

James E. from WAYNE, MI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Followup Repair to Install Door Trim

I had to unscrew the handle from the door as well as take out the front glass, put the trim in place (Thank God for the bottom placement nipples on each trimpiece), hold everything together after aligning all the pieces in place while I screwed the handle back on. The reason I was replacing the trim in the first place was that it is fragile plastic that had broken on both sides when I replaced one inner glass piece that had broken.

Parts Used:

Door Trim

Range Trim Side (Biscuit Right Hand

John from Madison, WI
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

last oven bottom was ruined by melted and burnt plastic

took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.

Parts Used:

Range Interior Bottom Oven Panel

Dennis from Missouri Valley, IA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Gas oven interment lighting. Pan was cracked and out of shape.

Loosen top two rear screws from the top pan. Remove top pan
Remove 2 front screws from bottom pan. Remove bottom pan. Reverse order.
Replace both pans.

Parts Used:

BAFFL-BRNR

Teddy from PRAIRIEVILLE, LA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

the oven temperature was not working right. I installed a new oven sensor. Works get now

Watch the video...

Parts Used:

Oven Sensor

Rosalind from APOLLO, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

temp level uneven

after watching the video, installed the temp sensor. Super easy

Parts Used:

Oven Sensor

Paul from HARMONY, MN
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Control knob broken

Slipped the old one off and slipped the new one on. Could not have been simplier.

Parts Used:

Range Control Knob

Ann from BROOKLYN, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Removed handle on oven door to remove front glass to clean when it slipped out of my hands.

To replace, the front glass slides into two holders on the bottom and three groves in the handle, then two screws to attach handle in place on the door.

Parts Used: